Bosch · Potentiometer 0-5 V

Bosch 0 280 755 051 accelerator pedal module

Bosch 0 280 755 051

Bosch 0 280 755 051 is a universal accelerator pedal module for drive-by-wire builds. Bosch Motorsport Australia lists about 16° (~70 mm, 2.8 in) of travel, a firewall-mounted hanging design, redundant dual potentiometer outputs and a 6-pin Compact mating connector, F 005 X11 508.1

Key specifications

Measures: Accelerator pedal position (two redundant potentiometer tracks). Output: Potentiometer 0-5 V.

TravelAbout 16°~70 mm / 2.8 inSourced1
MountingFirewall-mounted, hangingSourced1
OutputsRedundant dual potentiometersSourced1
Mating connector6-pin Compact, F 005 X11 508Sourced1
Connector pinoutUnverifiedNot published on the Bosch page cited; reseller pinouts are not used here.Researched, unverified
Track slopesUnverifiedNot published on the Bosch page cited.Researched, unverified
Part numberMakerNote
0 280 755 051Bosch1

Pinout and connector

No pinout is shown: the maker or OEM does not publish one in a document we could cite. Identify pins with a meter before wiring.

Connector: Bosch 6-pin Compact; mating part F 005 X11 5081 Connector library

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptConfigurable (generic input)Pedal tracks on AVI3/AVI4 (pins 19-20) with the pull-up off, sensor 5 V on pin 28 and sensor ground on pin 29 of the ECU2. Concept hardware: the drive-by-wire path needs qualified-human review before release.Medium4
Haltech (Elite / Nexus)UnverifiedNot checked against a public Haltech document that names this pedal. Confirm drive-by-wire support and the setup with Haltech before wiring.No public source
Link (G4X)UnverifiedNot checked against a public Link document that names this pedal. Confirm drive-by-wire support and the setup with Link before wiring.No public source
MoTeC (M1)UnverifiedNot checked against a public MoTeC document that names this pedal. Confirm drive-by-wire support and the setup with MoTeC before wiring.No public source
ECUMaster (EMU Black)UnverifiedNot checked against a public ECUMaster document that names this pedal. Confirm drive-by-wire support and the setup with ECUMaster before wiring.No public source
AEM (Infinity)UnverifiedNot checked against a public AEM document that names this pedal. Confirm drive-by-wire support and the setup with AEM before wiring.No public source
MaxxECUUnverifiedNot checked against a public MaxxECU document that names this pedal. Confirm drive-by-wire support and the setup with MaxxECU before wiring.No public source
Holley (Terminator X / EFI)UnverifiedNot checked against a public Holley document that names this pedal. Confirm drive-by-wire support and the setup with Holley before wiring.No public source

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

The maker does not publish a data sheet, drawing or CAD model for this part that we could find.

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Wiring and installation

Bosch Motorsport Australia sells this pedal for ECUs that control electronic throttle bodies, alongside its 32-82 mm throttle bodies. Wire each potentiometer track to its own analog input.12

Keep each track's 5 V reference and ground separate where the ECU provides them, so one shorted circuit cannot take out both tracks.Medium3

Failure modes and checks

Throttle limited under full pedal

Likely cause Pedal tracks disagree (connector or worn track)

Check Log both tracks through a slow press; the relation between them should stay constant over the 16° of travel.Medium13

No throttle response at all

Likely cause Lost 5 V reference to the pedal

Check Measure each reference at the F 005 X11 508 connector with the key on.Medium13

Frequently asked

What connector does the Bosch 0 280 755 051 pedal use?

A 6-pin Compact connector; Bosch Motorsport Australia lists mating connector F 005 X11 508.1

How much travel does the Bosch accelerator pedal module have?

About 16°, roughly 70 mm (2.8 in) at the pedal, per Bosch Motorsport Australia.1

Is the Bosch pedal floor or firewall mounted?

Firewall mounted, with a hanging pedal arm.1

Related

Use it with GAINS

Bosch 0 280 755 051 accelerator pedal module on GAINS hardware

ECU2AVI3-AVI4 (drive-by-wire APP1/APP2)

Pins
On the ECU2 pin map
Pull-up
Off
Shielding
Not needed

Pedal tracks for drive-by-wire. DBW sensors are allowed only on AVI1-6, never on a flex pin or CAN.Medium4

Analog inputs AVI1-6 take 0-5 V sensors, thermistors or switches, each with a switchable pull-up. Sensor 5 V is pin 28 (250 mA shared) and sensor ground is pin 29.4

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.45

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

  1. Accelerator Pedal Module 0 280 755 051 · Bosch Motorsport Australia (Robert Bosch Australia) · vendor-doc · retrieved 2026-11-04
  2. Electronic Throttle Body (40mm bore) 0 280 750 149 · Bosch Motorsport Australia (Robert Bosch Australia) · vendor-doc · retrieved 2026-11-04
  3. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  4. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  5. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)