GM · Analog 0-5 V (ratiometric)

GM 25832864 accelerator pedal (2007-11 GM full-size truck and SUV)

GM 25832864GM 15847349

GM 25832864 is the accelerator pedal with position sensor for 2007-11 GM full-size trucks and SUVs: Silverado and Sierra, Tahoe, Suburban, Yukon, Avalanche, Escalade and 2008-09 Hummer H2. It replaces 15847349. GM's dealer catalog gives fitment but not the pinout.1

Key specifications

Measures: Accelerator pedal position (redundant tracks). Output: Analog 0-5 V (ratiometric).

GM description
  • Pedal, accelerator pedal
  • Pedal travel sensor
Sourced1
Supersession15847349→ 25832864Sourced1
Shipping weight1.20lb0.5 kgDealer listing weight.Sourced · medium1
Connector and pinoutUnverifiedGM's public parts catalog does not publish the pedal pinout; reseller and forum pinouts are not used here.Researched, unverified
Track slopesUnverifiedNot published in the GM data cited.Researched, unverified
Part numberMakerNote
25832864GM1
15847349GMReplaced by 258328641

Pinout and connector

No pinout is shown: the maker or OEM does not publish one in a document we could cite. Identify pins with a meter before wiring.

Connector not published. Browse the connector library

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptConfigurable (generic input)Pedal tracks on AVI3/AVI4 (pins 19-20) with the pull-up off, sensor 5 V on pin 28 and sensor ground on pin 29 of the ECU2. Concept hardware: the drive-by-wire path needs qualified-human review before release.Medium3
Haltech (Elite / Nexus)UnverifiedNot checked against a public Haltech document that names this pedal. Confirm drive-by-wire support and the setup with Haltech before wiring.No public source
Link (G4X)UnverifiedNot checked against a public Link document that names this pedal. Confirm drive-by-wire support and the setup with Link before wiring.No public source
MoTeC (M1)UnverifiedNot checked against a public MoTeC document that names this pedal. Confirm drive-by-wire support and the setup with MoTeC before wiring.No public source
ECUMaster (EMU Black)UnverifiedNot checked against a public ECUMaster document that names this pedal. Confirm drive-by-wire support and the setup with ECUMaster before wiring.No public source
AEM (Infinity)UnverifiedNot checked against a public AEM document that names this pedal. Confirm drive-by-wire support and the setup with AEM before wiring.No public source
MaxxECUUnverifiedNot checked against a public MaxxECU document that names this pedal. Confirm drive-by-wire support and the setup with MaxxECU before wiring.No public source
Holley (Terminator X / EFI)UnverifiedNot checked against a public Holley document that names this pedal. Confirm drive-by-wire support and the setup with Holley before wiring.No public source

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

The maker does not publish a data sheet, drawing or CAD model for this part that we could find.

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Engines that use it

From the platform catalog's sensor table; check fitment against your engine code and model year.

Wiring and installation

The pedal is listed for gas V6 and V8 and 6.6 diesel trucks alike, so it is a widely available donor. Each pedal track needs its own analog input on the ECU that runs the throttle.Medium12

Keep each track's 5 V reference and ground separate where the ECU provides them, so one shorted circuit cannot take out both tracks.Medium2

Failure modes and checks

Throttle limited under full pedal

Likely cause Pedal tracks disagree (connector corrosion or worn track)

Check Log both pedal tracks through a slow press; the relation between them should stay constant.Medium2

No throttle response at all

Likely cause Lost 5 V reference to the pedal

Check Measure each reference at the pedal connector with the key on.Medium2

Frequently asked

What replaced GM 15847349?

25832864, per GM dealer catalog data.1

What trucks use GM pedal 25832864?

2007-11 Silverado and Sierra (including HD), Tahoe, Suburban, Yukon, Avalanche and Escalade, and 2008-09 Hummer H2, per GM's dealer catalog.1

Can a truck pedal be used in an LS swap?

Yes, if the ECU runs electronic throttle control and you have the pedal's pinout from GM service data. GM's parts catalog gives fitment only.Low12

Related

Use it with GAINS

GM 25832864 accelerator pedal (2007-11 GM full-size truck and SUV) on GAINS hardware

ECU2AVI3-AVI4 (drive-by-wire APP1/APP2)

Pins
On the ECU2 pin map
Pull-up
Off
Shielding
Not needed

Pedal tracks for drive-by-wire. DBW sensors are allowed only on AVI1-6, never on a flex pin or CAN.Medium3

Analog inputs AVI1-6 take 0-5 V sensors, thermistors or switches, each with a switchable pull-up. Sensor 5 V is pin 28 (250 mA shared) and sensor ground is pin 29.3

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.34

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

  1. GM 25832864 Pedal, Accelerator Pedal (Pedal Travel Sensor) · GMPartsGiant (GM parts dealer) · oem · retrieved 2026-11-04
  2. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  3. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  4. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)