Sensor type · Potentiometer 0-5 V · Hall effect (digital)
Electronic throttle body
A drive-by-wire throttle body is an electronic throttle body (ETB): a DC motor opens the throttle plate against a return spring while two redundant position tracks report its angle. A typical body has six wires: motor plus and minus, sensor 5 V, sensor ground and two signals. It needs an ECU with electronic throttle control and an accelerator pedal module.124
Parts in the library
Support across ECUs
Across the 10 parts in this hub (2 with a maker-verified pinout). Open a part for the setup notes and sources.
Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.
How it works
Bosch describes a typical electronic throttle control system as three parts: the throttle body, an accelerator pedal module and an ECU with throttle control. The ECU turns pedal position into a target angle and drives the motor until the throttle sensors match it.13
The motor is driven in both directions from an H-bridge, a four-switch output stage that can reverse current. A return spring pulls the plate to a default opening when the motor is unpowered; Bosch states every one of its ETBs has this idle-air position, so the engine can limp home at a fast idle.Medium13
Two position sensors read the same shaft. On Bosch's bodies output I runs 0 to 5 V and output II 5 to 0 V over 0-90°, from a 5 ± 0.2 V supply. The ECU cross-checks them continuously and cuts throttle authority when they disagree.1
Types and variants
Bosch Motorsport lists 32-82 mm bores with redundant potentiometer tracks and 6-pin connectors. Pin order differs between bore sizes: the 46 and 52 mm bodies use mating connector D 261 205 356-01 and a different layout from the others (D 261 205 358-01).12
Factory bodies such as GM's 87 mm (12629992) and 90 mm (12605109) LS units and Ford's 2011-14 Coyote body are common swap parts. GM and Ford parts catalogs do not publish their pinouts or sensor element type.Medium657
K-series engines moved to drive-by-wire in some models, such as the 2006-08 Acura TSX body 16400-RBB-A01. Honda's catalog gives fitment but no pinout.Medium8
Wiring
Run both throttle tracks and the motor pair straight to the ECU that performs throttle control, never through CAN or another module. Use the ECU's own sensor 5 V and sensor ground, never chassis ground.Medium19
The motor pair carries several amps in both directions. Size the wire for the H-bridge's peak current and keep it away from the sensor tracks; Bosch rates its bodies for 6-16 V with a generator current below 10 A.Medium1
Never assume one pinout for a family. Bosch's own sheet swaps motor and sensor pins between bore sizes, and a reversed motor drives the plate the wrong way at power-up. Check pins against the maker's document for the exact part number.2
Common faults and checks
Likely cause The two position tracks disagree
Check Log both tracks while the ECU sweeps the throttle; on a Bosch body output I plus output II should stay near the 5 V supply.Medium1
Likely cause Motor wires reversed or the wrong pin map for that body
Check Compare each pin with the maker's pinout for that exact part number before powering the motor.Medium2
Likely cause Mounting stress or debris holding the plate
Check Remove power, check the plate returns to its rest opening by spring force alone, and check the mounting against the maker's notes.Medium1
Frequently asked
How does a drive-by-wire throttle body work?
The ECU reads the accelerator pedal, sets a target throttle angle and drives a DC motor on the throttle shaft until two position sensors report that angle. A spring returns the plate to a default opening if power is lost.Medium13
How many wires does a drive-by-wire throttle body have?
Usually six: motor plus, motor minus, sensor 5 V, sensor ground and two position signals. Bosch's motorsport bodies and GM's LS bodies use 6-pin connectors.Medium26
Can any ECU run a drive-by-wire throttle body?
No. The ECU needs a bidirectional motor driver (an H-bridge), two spare analog inputs for the throttle tracks, two for the pedal, and throttle-control software with plausibility checks. Bosch states its bodies connect directly to ECUs with that function.Medium13
What is the limp-home position on a throttle body?
The opening the return spring holds when the motor is off. Bosch says all of its electronic throttle bodies have this idle-air position, which lets the engine keep running slowly after a fault.1
Do drive-by-wire throttle body pinouts differ?
Yes, even within one maker's range. Bosch's 46 and 52 mm bodies put the sensor signals on pins 1 and 4 and the motor on pins 3 and 5, while its other bores use pins 1 and 4 for the motor.2
Related
Use it with GAINS
Electronic throttle body on GAINS hardware
Throttle sensors go on AVI1/AVI2 and pedal sensors on AVI3/AVI4; the throttle motor runs from HB1/HB2. DBW sensors are allowed only on AVI1-6, never on a flex pin or CAN.9
GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet. The DBW path needs qualified-human review before release.910
Concept Pre-release hardware. Pin assignments come from the current design documents and may change.
Sources
10 sources
- Electronic Throttle Body data sheet 68749835 (51017995, 27 Jan 2026) · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-11-04
- Electronic Throttle Body Variations: pin layouts PDF 147514891 · Bosch Motorsport · vendor-doc · retrieved 2026-11-04
- Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
- DR-525 Series Crate Engine Control System instruction sheet (kit 19354340) · Chevrolet Performance (GM) · oem · retrieved 2026-11-04
- 90mm LS3 throttle body, Genuine GM 12605109 / 19420707 / ACDelco 217-3153 · Michigan Motorsports (GM parts retailer) · vendor-doc · retrieved 2026-11-04
- 87mm throttle body, Genuine GM 12629992 / ACDelco 217-3151 · Michigan Motorsports (GM parts retailer) · vendor-doc · retrieved 2026-11-04
- Ford BR3Z-9E926-C Throttle Body And Motor Assembly · FordPartsGiant (Ford parts dealer) · oem · retrieved 2026-11-04
- Genuine Acura 16400-RBB-A01 Throttle Body, Electronic Control (GMA9A) · AutoPartsPrime (Honda/Acura parts dealer) · oem · retrieved 2026-11-04
- internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
- internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)

