GM · Analog 0-5 V (ratiometric)

GM 12605109 90 mm drive-by-wire throttle body (LS3 / L99 / LS7)

GM 12605109GM 19420707GM 19540179ACDelco 217-3153

GM 12605109 is the 90 mm, 4-bolt drive-by-wire throttle body used on LS3, L99, LS7 and L76/L77 V8s. GM superseded it to 19420707 and then 19540179; ACDelco sells it as 217-3153. GM's catalog lists the 2009-13 Corvette, 2010-15 Camaro SS and Z/28, 2014-17 Chevrolet SS, 2011-17 Caprice PPV and 2009 Pontiac G8.Medium213

Key specifications

Measures: Throttle plate angle (redundant tracks); motor-driven throttle actuator. Output: Analog 0-5 V (ratiometric).

Bore90mm3.54 inSourced · medium3
Mounting
  • 4-bolt LS3-style flange
  • Suits 90-92 mm intake manifolds
Sourced · medium3
Supersession12605109 → 19420707 → 19540179Sourced12
GM descriptionBody, fuel injection air meterwith throttle actuatorSourced1
Connector pinoutUnverifiedGM's public parts catalog does not publish the pinout; reseller and forum pinouts are not used here.Researched, unverified
Sensor type and output slopesUnverifiedNot published in the GM parts data cited.Researched, unverified
Part numberMakerNote
12605109GM12
19420707GMReplaces 1260510923
19540179GMCurrent replacement for 19420707 / 1260510912
217-3153ACDelcoMedium3

Pinout and connector

No pinout is shown: the maker or OEM does not publish one in a document we could cite. Identify pins with a meter before wiring.

Connector not published. Browse the connector library

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptConfigurable (generic input)Throttle tracks on AVI1/AVI2 (pins 17-18) with the pull-up off; motor on the H-bridge pins 21-22 of the ECU2. Concept hardware: the drive-by-wire path needs qualified-human review before release.Medium6
Haltech (Elite / Nexus)UnverifiedNot checked against a public Haltech document that names this throttle body. Confirm drive-by-wire support and the setup with Haltech before wiring.No public source
Link (G4X)UnverifiedNot checked against a public Link document that names this throttle body. Confirm drive-by-wire support and the setup with Link before wiring.No public source
MoTeC (M1)UnverifiedNot checked against a public MoTeC document that names this throttle body. Confirm drive-by-wire support and the setup with MoTeC before wiring.No public source
ECUMaster (EMU Black)UnverifiedNot checked against a public ECUMaster document that names this throttle body. Confirm drive-by-wire support and the setup with ECUMaster before wiring.No public source
AEM (Infinity)UnverifiedNot checked against a public AEM document that names this throttle body. Confirm drive-by-wire support and the setup with AEM before wiring.No public source
MaxxECUUnverifiedNot checked against a public MaxxECU document that names this throttle body. Confirm drive-by-wire support and the setup with MaxxECU before wiring.No public source
Holley (Terminator X / EFI)UnverifiedNot checked against a public Holley document that names this throttle body. Confirm drive-by-wire support and the setup with Holley before wiring.No public source

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

The maker does not publish a data sheet, drawing or CAD model for this part that we could find.

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Engines that use it

From the platform catalog's sensor table; check fitment against your engine code and model year.

Wiring and installation

This is a drive-by-wire body: it needs an ECU with electronic throttle control and a matching accelerator pedal. GM's crate-engine controller instructions forbid altering the pedal or throttle wiring on its kits.Medium4

A GM parts retailer notes that pre-2008 drive-by-wire trucks need a wiring adapter to run this later body. Check your ECU's throttle-control support before swapping.Low3

Failure modes and checks

Reduced engine power after fitting

Likely cause Throttle tracks disagree or the ECU has not learned the new body

Check Log both throttle tracks and confirm they track smoothly; run the ECU's throttle relearn.Low5

Idle hunting after an intake swap

Likely cause Air leak at the throttle body seal

Check GM's dealer data calls for a new seal when the body is refitted; check the seal is seated.Low2

Frequently asked

What replaced GM 12605109?

GM superseded 12605109 to 19420707, and 19420707 to 19540179. ACDelco's number is 217-3153.123

What size is the LS3 throttle body?

90 mm (3.54 in), with a 4-bolt flange, per a GM parts retailer.Medium3

What cars came with the 12605109 throttle body?

GM's catalog for its successor 19420707 lists the 2009-13 Corvette, 2010-15 Camaro SS and Z/28, 2014-17 Chevrolet SS, 2011-17 Caprice PPV and 2009 Pontiac G8.2

Will an LS3 throttle body fit an older LS truck?

It bolts to LS3-style 4-bolt intakes. A GM parts retailer says 1999-2007 drive-by-wire trucks need a wiring adapter to run it; cable-throttle engines need a full drive-by-wire conversion.Low3

Related

Use it with GAINS

GM 12605109 90 mm drive-by-wire throttle body (LS3 / L99 / LS7) on GAINS hardware

ECU2AVI1-AVI2 (TPS1/TPS2) + HB1/HB2 (motor)

Pins
On the ECU2 pin map
Pull-up
Off
Shielding
Not needed

Throttle tracks on AVI1/AVI2, motor on the H-bridge pins 21-22 (about 3 A continuous / 10 A peak, under review). DBW sensors never over CAN.Medium6

Drive-by-wire control is safety-relevant; the ECU2's DBW path needs qualified-human review before release.6

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.67

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

  1. GM 12605109 Body, Fuel Injection Air Meter · GMPartsGiant (GM parts dealer) · oem · retrieved 2026-11-04
  2. GM 19420707 throttle body (replaces 12605109): fitment · ChevyPartsDeal (GM parts dealer) · oem · retrieved 2026-11-04
  3. 90mm LS3 throttle body, Genuine GM 12605109 / 19420707 / ACDelco 217-3153 · Michigan Motorsports (GM parts retailer) · vendor-doc · retrieved 2026-11-04
  4. DR-525 Series Crate Engine Control System instruction sheet (kit 19354340) · Chevrolet Performance (GM) · oem · retrieved 2026-11-04
  5. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  6. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  7. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)