Bosch · Potentiometer 0-5 V

Bosch 0 280 750 474 electronic throttle body (74 mm)

Bosch 0 280 750 474

Bosch 0 280 750 474 is a 74 mm electronic throttle body with dual potentiometer tracks, sold by Bosch Motorsport Australia for custom drive-by-wire builds with mating connector D 261 205 358-01. Bosch Motorsport's data sheet and pin-layout sheet do not cover a 74 mm bore, so its pinout here is unverified.Medium42

Key specifications

Measures: Throttle plate angle (two redundant tracks); motor-driven throttle actuator. Output: Potentiometer 0-5 V.

Bore74mm2.91 inSourced4
RedundancyDual potentiometer tracksSourced4
Mating connectorD 261 205 358-01Sourced4
Application
  • Generic and custom applications
  • Needs an electronic pedal and an ECU running throttle control
Sourced4
Connector pinoutUnverifiedNot in Bosch's pin-layout sheet, which skips the 74 mm bore; reseller pinouts are not used here.Researched, unverified
Flange and hole patternUnverifiedNot published in the Bosch documents cited.Researched, unverified
Sensor supply and output slopesUnverifiedBosch Motorsport's data sheet does not list a 74 mm body.Researched, unverified
Part numberMakerNote
0 280 750 474Bosch74 mm bore4

Pinout and connector

No pinout is shown: the maker or OEM does not publish one in a document we could cite. Identify pins with a meter before wiring.

Connector: Bosch 6-pin (AMP) throttle body connector; mating part D 261 205 358-014 Connector library

Terminals and seals: Sold with the mating housing by Bosch Motorsport; terminal numbers not listed on the pages cited.

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptConfigurable (generic input)Throttle tracks on AVI1/AVI2 (pins 17-18) with the pull-up off; motor on the H-bridge pins 21-22 of the ECU2. Concept hardware: the drive-by-wire path needs qualified-human review before release.Medium5
Haltech (Elite / Nexus)UnverifiedNot checked against a public Haltech document that names this throttle body. Confirm drive-by-wire support and the setup with Haltech before wiring.No public source
Link (G4X)UnverifiedNot checked against a public Link document that names this throttle body. Confirm drive-by-wire support and the setup with Link before wiring.No public source
MoTeC (M1)UnverifiedNot checked against a public MoTeC document that names this throttle body. Confirm drive-by-wire support and the setup with MoTeC before wiring.No public source
ECUMaster (EMU Black)UnverifiedNot checked against a public ECUMaster document that names this throttle body. Confirm drive-by-wire support and the setup with ECUMaster before wiring.No public source
AEM (Infinity)UnverifiedNot checked against a public AEM document that names this throttle body. Confirm drive-by-wire support and the setup with AEM before wiring.No public source
MaxxECUUnverifiedNot checked against a public MaxxECU document that names this throttle body. Confirm drive-by-wire support and the setup with MaxxECU before wiring.No public source
Holley (Terminator X / EFI)UnverifiedNot checked against a public Holley document that names this throttle body. Confirm drive-by-wire support and the setup with Holley before wiring.No public source

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Wiring and installation

The mating connector is the same part Bosch lists for its 32-82 mm range, but Bosch's pin order changes between bodies. Identify the motor pair with a meter (low resistance) before powering it.Medium42

Failure modes and checks

Throttle drives the wrong way at key-on

Likely cause Motor polarity reversed for this body

Check With the motor unplugged, confirm which pair is the motor and which pins move with the plate, then wire to the ECU's H-bridge.Low2

Limp idle with a throttle fault

Likely cause Track disagreement

Check Log both tracks through a slow sweep; they should move in opposite directions without steps.Low41

Frequently asked

What connector does Bosch 0 280 750 474 use?

Bosch Motorsport Australia lists mating connector D 261 205 358-01, a 6-pin housing.4

What is the pinout of the Bosch 74 mm throttle body?

Bosch's public pin-layout sheet does not include a 74 mm body, so we do not publish one. Bosch's other bores share the connector but not always the pin order.24

Does the Bosch 74 mm throttle body need a drive-by-wire ECU?

Yes. Bosch Motorsport Australia states it needs an electronic accelerator pedal and an ECU capable of electronic throttle control.4

Related

Use it with GAINS

Bosch 0 280 750 474 electronic throttle body (74 mm) on GAINS hardware

ECU2AVI1-AVI2 (TPS1/TPS2) + HB1/HB2 (motor)

Pins
On the ECU2 pin map
Pull-up
Off
Shielding
Not needed

Throttle tracks on AVI1/AVI2, motor on the H-bridge pins 21-22 (about 3 A continuous / 10 A peak, under review). DBW sensors never over CAN.Medium5

Drive-by-wire control is safety-relevant; the ECU2's DBW path needs qualified-human review before release.5

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.56

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

  1. Electronic Throttle Body data sheet 68749835 (51017995, 27 Jan 2026) · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-11-04
  2. Electronic Throttle Body Variations: pin layouts PDF 147514891 · Bosch Motorsport · vendor-doc · retrieved 2026-11-04
  3. ELECTRONIC THROTTLE BODY product page (downloads) · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  4. Electronic Throttle Body (74mm bore) 0 280 750 474 · Bosch Motorsport Australia (Robert Bosch Australia) · vendor-doc · retrieved 2026-11-04
  5. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  6. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)

Not yet indexed: more than 40% of specs unverified.