Pressure ratio (turbo compressor)

PRcompressor pressure ratioboost pressure ratioΠ_c

Pressure ratio is the absolute pressure at a turbo compressor's outlet divided by the absolute pressure at its inlet. It is the vertical axis of a compressor map and, with corrected mass flow, locates the operating point. Because it uses absolute pressures, the same gauge boost means a higher pressure ratio at altitude.123

How it works

Garrett defines pressure ratio as absolute outlet pressure divided by absolute inlet pressure.

Gauge boost must therefore have atmospheric pressure added before dividing. At sea level, 14.7 psi (1.013 bar) of boost is roughly a pressure ratio of 2.0.1

Outlet pressure is higher than manifold pressure because the intercooler and charge piping cause a pressure drop. Inlet pressure is lower than ambient because the air filter and intake tract cause a depression. Both raise the real pressure ratio above the simple boost-gauge figure, and Garrett's method includes them.14

Atmospheric pressure falls with altitude. The US Standard Atmosphere gives about 12.2 psi (84 kPa) at 5,000 ft (1,524 m), against 14.7 psi at sea level. Holding the same absolute manifold pressure at altitude therefore needs a higher pressure ratio and more turbo speed.31

Compressing air also heats it. For a given compressor efficiency, outlet temperature rises with pressure ratio, which is why higher boost places more demand on the intercooler and on knock control.21

In tuning

Use pressure ratio, not boost, when checking a turbo match.

Plot each target at several engine speeds on the compressor map, including real filter and intercooler losses, and check it stays between surge and choke at the altitudes the car will see.1

Targeting absolute manifold pressure keeps engine air mass more consistent across weather and altitude, but pushes the turbo harder up high. Many strategies cap pressure ratio or turbo speed with a barometric correction to protect the compressor.Medium43

Formula and worked example

PR = (P_boost + P_atm + ΔP_loss) / (P_atm − ΔP_inlet)
PR
compressor pressure ratio (dimensionless)
P_boost
manifold gauge boost pressurepsi or kPa
P_atm
local atmospheric pressurepsi or kPa
ΔP_loss
pressure drop between compressor outlet and manifold (intercooler, piping)psi or kPa
ΔP_inlet
pressure drop across the air filter and inlet tractpsi or kPa
1

Try it

psi
ft
psi
psi

Result

Pressure ratio2.29 :1
Ambient pressure14.70 psi
Manifold absolute pressure29.4 psi

Planning estimate from the formula below, not a measurement.

Open the full turbo pressure ratio calculator →

Myths vs facts

Myth Pressure ratio is just boost divided by 14.7.

Fact It is absolute outlet pressure over absolute inlet pressure. You must add atmospheric pressure to gauge boost and account for local altitude and system losses.1

Myth The same boost setting loads the turbo equally everywhere.

Fact At altitude, ambient pressure is lower, so the same absolute manifold pressure needs a higher pressure ratio and more turbo speed.31

Frequently asked

How do you calculate turbo pressure ratio?

Add atmospheric pressure to the gauge boost, add any pressure drop between compressor and manifold, then divide by the absolute pressure at the compressor inlet. At sea level with no losses, 20 psi boost gives (20 + 14.7) ÷ 14.7 = 2.36. Real systems run a little higher once intercooler and filter losses are included.1

Why does pressure ratio go up at altitude?

Atmospheric pressure falls as altitude rises, to about 12.2 psi at 5,000 ft in the US Standard Atmosphere. If the engine targets the same absolute manifold pressure, the compressor must multiply a lower inlet pressure by more, so pressure ratio and turbo speed rise. A turbo near its limit at sea level can overspeed at altitude.31

Why include intercooler pressure drop in pressure ratio?

The compressor has to make the manifold pressure plus whatever the intercooler and piping lose on the way. If the intercooler drops 2 psi, the compressor outlet is 2 psi higher than the manifold reading. Ignoring it places operating points too low on the compressor map and can hide a surge or choke problem.14

Is pressure ratio the same as boost?

No. Boost is usually gauge pressure above local atmosphere, in psi or bar. Pressure ratio is dimensionless and compares absolute outlet pressure with absolute inlet pressure. Compressor maps use pressure ratio because it describes the compressor's work independent of the weather and altitude where it runs.12

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Turbo Tech 103 (Expert): compressor mapping · Garrett Motion · vendor-doc · retrieved 2026-10-27
  2. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-27
  3. U.S. Standard Atmosphere, 1976 · NOAA / NASA / USAF (NASA Technical Reports Server) · standard · retrieved 2026-10-27
  4. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27