Turbo compressor map

compressor mapturbo mapcompressor efficiency mapsurge linechoke line

A turbo compressor map is a chart of a compressor's performance, plotting pressure ratio against air mass flow. It shows the surge limit, the choke limit, lines of constant shaft speed and efficiency islands, so you can check whether an engine's airflow needs fall where the compressor works well.1

How it works

The vertical axis is pressure ratio

Absolute outlet pressure divided by absolute inlet pressure. The horizontal axis is mass flow, usually in lb/min or kg/s. Garrett stresses using absolute pressure, so a boost gauge reading must be added to atmospheric pressure.1

The surge line is the left boundary. To its left, flow is too low for the pressure ratio and becomes unstable, with fluttering boost and heavy thrust loading on the bearings. Garrett describes ported shroud housings that move this line left.1

The choke line is the right boundary. Garrett typically defines it where efficiency falls below 58 percent. Speed lines crowd together near it, so turbo speed rises quickly and overspeed becomes likely.1

Efficiency islands are rings of constant adiabatic efficiency. The smallest central island is the peak. Lower efficiency means more compressor work turns into heat, raising outlet temperature and load on the intercooler.12

Outlet temperature follows from pressure ratio and efficiency. Ideal compression raises absolute temperature by the factor PR^((γ−1)/γ), with γ about 1.4 for air, and the actual rise is that ideal rise divided by compressor efficiency. Higher ratios and lower efficiency both mean hotter charge air.32

In tuning

To use a map, estimate the engine's required airflow and pressure ratio at several rpm points, then plot them.

Points should run right of surge, left of choke and through the efficient middle. Garrett gives a rough rule of 9.5 to 10.5 flywheel hp per lb/min for turbocharged gasoline engines.1

Include inlet losses and altitude. Garrett's example shows how a 1 psi (0.07 bar) filter restriction raises pressure ratio, and how the same boost at 5,000 ft (1,524 m) altitude means a much higher ratio than at sea level.1

Maps come from the turbo manufacturer for a specific compressor wheel and housing, measured under standard inlet conditions. Treat them as the maker's data, and match the exact wheel and trim when reading one.Medium1

Formula and worked example

PR = (P_boost + P_atm) / (P_atm − ΔP_inlet)
PR
compressor pressure ratio
P_boost
gauge boost pressure at the compressor outletpsi or bar
P_atm
absolute atmospheric pressurepsi or bar
ΔP_inlet
pressure loss before the compressor (air filter and ducting)psi or bar
1

Try it

psi
ft
psi
psi

Result

Pressure ratio2.29 :1
Ambient pressure14.70 psi
Manifold absolute pressure29.4 psi

Planning estimate from the formula below, not a measurement.

Open the full turbo pressure ratio calculator →

Myths vs facts

Myth Boost pressure equals pressure ratio.

Fact Pressure ratio uses absolute pressures at outlet and inlet. 15 psi of boost is about 2.0, not 15, and it rises with altitude and inlet restriction.1

Myth A bigger turbo is always better.

Fact An oversized compressor can operate in or near surge at low engine flow and spools later. The right size puts the engine's points in the efficient middle.1

Frequently asked

How do you read a turbo compressor map?

Find the engine's pressure ratio on the vertical axis and its mass airflow on the horizontal axis. The point shows turbo speed from the nearby speed lines and efficiency from the island it falls in. It should sit right of the surge line, left of the choke line and as near the central efficiency island as possible.1

What is pressure ratio on a compressor map?

Pressure ratio is absolute compressor outlet pressure divided by absolute inlet pressure. Add atmospheric pressure to gauge boost and subtract any inlet restriction from the inlet side. At sea level with 12 psi of boost and no inlet loss, Garrett calculates 26.7 / 14.7, about 1.82.1

What is the surge line?

The surge line is the left-hand limit of the map. To its left, airflow is too low for the pressure ratio and flow through the compressor becomes unstable. It shows up as fluttering boost and barking. Garrett warns continued surge causes heavy thrust loading and premature turbo failure.1

What is the choke line?

The choke line is the right-hand limit, where the compressor cannot flow more air efficiently. Garrett typically defines it as the point where efficiency falls below 58 percent. Beyond it, turbo speed climbs rapidly toward overspeed, so a larger compressor is needed for that flow.1

How do I pick a turbo from a compressor map?

Set a power target, estimate mass airflow and pressure ratio at several engine speeds, and plot those points. Choose a compressor whose map keeps all points between surge and choke, with the main operating range near peak efficiency. Then check turbine sizing and spool, which the compressor map does not show.1

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Turbo Tech 103 (Expert): compressor maps · Garrett Motion · vendor-doc · retrieved 2026-10-25
  2. Turbocharger · Wikipedia · reference · retrieved 2026-10-25
  3. Internal Combustion Engine Fundamentals, 2nd edition (J. B. Heywood) · McGraw-Hill Education · book · retrieved 2026-10-25