Compressor choke

choke linechoke flowstonewallcompressor choke lineturbo choke

Compressor choke is the maximum-flow limit of a turbocharger compressor, shown as the choke line on the right-hand edge of the compressor map. Near choke, efficiency falls steeply and extra flow needs much more wheel speed, so outlet temperature rises and the turbo risks overspeed. It signals a compressor too small for the airflow.123

How it works

Every compressor wheel has a flow it cannot exceed at a given speed, set by how much air its inducer and passages can pass.

Approaching that limit, gas velocities approach sonic conditions in the narrowest passages and flow stops responding to lower outlet pressure. This is the same physics as choked flow in a nozzle.Medium23

Garrett draws the choke line as the right-hand boundary of its compressor maps and typically defines it where efficiency drops below 58%. Other makers use different efficiency or slope criteria, so choke lines on maps from different suppliers are not strictly comparable.1

Past the choke limit, turbo speed rises very quickly for little extra flow, and Garrett warns that overspeed becomes very likely. Low efficiency also means much hotter outlet air, which loads the intercooler and reduces knock margin.14

In tuning

Plot operating points at high engine speed on the compressor map.

Garrett's worked example shows a compressor whose high-rpm points fall beyond the choke line, which it describes as clearly too small. Raising boost on such a turbo adds heat and shaft speed faster than it adds air.1

Altitude moves the operating point toward choke. Lower inlet pressure means a higher pressure ratio and higher wheel speed for the same manifold pressure, so a turbo near its limit at sea level can overspeed at altitude unless boost is reduced.Medium15

Try it

psi
ft
psi
psi

Result

Pressure ratio2.29 :1
Ambient pressure14.70 psi
Manifold absolute pressure29.4 psi

Planning estimate from the formula below, not a measurement.

Open the full turbo pressure ratio calculator →

Myths vs facts

Myth More boost always means more airflow from the same turbo.

Fact Near choke, the compressor cannot pass much more mass flow regardless of shaft speed. Turning the boost up mostly raises outlet temperature and turbo speed.13

Myth Choke and surge are two names for the same problem.

Fact They are opposite limits. Surge is the low-flow instability on the left of the map; choke is the maximum-flow limit on the right.1

Frequently asked

What is the choke line on a compressor map?

It is the right-hand boundary of the map, marking the maximum flow the compressor can pass usefully at each pressure ratio. Garrett typically draws it where compressor efficiency falls below 58%. Operating points beyond it mean the compressor is too small for the engine's airflow at that speed.1

What happens when a turbo is too small?

At high engine speed the compressor runs into choke. Efficiency drops, outlet air gets much hotter and wheel speed climbs quickly, raising the risk of overspeed. Boost may hold, but power tapers off because air mass flow stops rising. Exhaust back pressure from a small turbine adds to the effect.16

What is the difference between surge and choke?

Surge is the low-flow limit on the left of a compressor map, where flow becomes unstable and reverses. Choke is the high-flow limit on the right, where the wheel cannot pass more air efficiently. A well-matched compressor keeps all operating points between the two, ideally in the higher-efficiency islands.1

Can compressor choke overspeed a turbo?

Yes. Beyond the choke line, turbo speed rises very quickly for little extra flow, and Garrett warns that overspeed is very likely. Running at altitude makes it worse because the pressure ratio for the same boost is higher. A turbo speed sensor or conservative boost targets protect against it.15

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Turbo Tech 103 (Expert): compressor mapping · Garrett Motion · vendor-doc · retrieved 2026-10-27
  2. Choked flow · Wikipedia · reference · retrieved 2026-10-27
  3. Centrifugal compressor · Wikipedia · reference · retrieved 2026-10-27
  4. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-27
  5. U.S. Standard Atmosphere, 1976 · NOAA / NASA / USAF (NASA Technical Reports Server) · standard · retrieved 2026-10-27
  6. Turbo Tech 101 (Basic): how a turbo system works · Garrett Motion · vendor-doc · retrieved 2026-10-27