Honda · Hall effect (digital)

Honda 37500-PNB-003 crank position sensor (K20Z)

Honda 37500-PNB-003

Honda 37500-PNB-003 (replacing 37500-PNA-003) is the crank position sensor Honda lists for the 2006-11 Civic Si K20Z3. Honda's parts catalog does not state the sensor technology, so confirm VR or Hall with a meter before configuring a standalone ECU input.4

Key specifications

Measures: Crank trigger wheel teeth. Output: Hall effect (digital).

Listed for2008Civic SiK20Z3Sourced4
Sensor technologyUnverifiedNot stated in the Honda catalog.Researched, unverified
Part numberMakerNote
37500-PNB-003HondaReplaces 37500-PNA-0034

Pinout and connector

No pinout is shown: the maker or OEM does not publish one in a document we could cite. Identify pins with a meter before wiring.

Connector not published. Browse the connector library

How it's calibrated

ECU-neutral: enter these values in whichever ECU you use. Nominal values without the maker's tolerance band.

Trigger setup

  • Trigger type: Hall effect (digital square wave).4
  • Trigger edge: not published by the maker. Confirm the edge your ECU uses with a scope or a timing light before running the engine.

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptTo be confirmedCRANK (pin 13) or CAM (pin 15) accept Hall in the concept, but the pull-up on these inputs is still an open item.Medium5
Haltech (Elite / Nexus)Configurable (generic input)Trigger or Home input in digital mode with the 5 V pull-up selected.Medium7
Link (G4X)Configurable (generic input)Trigger input; Link sells a Hall sensor kit listed for all Link ECUs.Medium8
MoTeC (M1)UnverifiedThe M150 page lists programmable digital inputs but does not name Hall trigger sensors.No public source
ECUMaster (EMU Black)Configurable (generic input)Trigger input (3: primary and 2 cams), Hall or VR selected in software.9
AEM (Infinity)Configurable (generic input)Crank or cam Hall input (10 kΩ pull-up to 12 V per AEM).10
MaxxECUConfigurable (generic input)Trigger input in digital mode, or an extra digital input for speed sensors.11
Holley (Terminator X / EFI)Configurable (generic input)Crank or cam input; Holley recommends Hall sensors.12

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

The maker does not publish a data sheet, drawing or CAD model for this part that we could find.

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Engines that use it

From the platform catalog's sensor table; check fitment against your engine code and model year.

Wiring and installation

Identify the type first: a two-pin sensor with a few hundred ohms across its pins is VR; a three-pin sensor needing a supply is Hall.Medium23

Failure modes and checks

No rpm

Likely cause Input type set wrong

Check Measure the sensor and set VR or Hall accordingly.Medium23

Crank code after timing chain work

Likely cause Connector unseated or air gap disturbed

Check Re-seat the sensor and check the connector.Low1

Frequently asked

What crank sensor does the 2006-11 Civic Si use?

Honda lists 37500-PNB-003, replacing 37500-PNA-003.4

Is the K20Z crank sensor VR or Hall?

Honda's catalog does not say. Measure it: VR sensors show coil resistance across two pins; Hall sensors need a supply.Medium42

Related

Use it with GAINS

Honda 37500-PNB-003 crank position sensor (K20Z) on GAINS hardware

ECU2CRANK (VR or Hall, single-ended, adaptive threshold)

Pins
On the ECU2 pin map
Pull-up
To be confirmed
Shielding
Shielded, drain at the ECU end only

Shielded cable, shield to sensor ground at the ECU end only. Hall pull-up arrangement to be confirmed in the schematic.Medium5

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.56

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

12 sources
  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. Inductive Speed Sensor IS-C data sheet · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  3. Speed Sensor Hall-Effect Mini-HA-P sealed data sheet 69875339 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  4. OEM sensor PNs (Honda Civic 2008/2012): 2008 Civic Si knock PRC-003, AF RRA-013, middle O2 RRA-004, crank PNB-003; 2012 Si knock R1A-A01, MAP RNA-A01, · hondapartsnow.com · oem · retrieved 2026-10-25
  5. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  6. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  7. Nexus R3 wiring diagram (HT-193000_WD) · Haltech · vendor-doc · retrieved 2026-10-27
  8. EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-10-27
  9. Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
  10. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-10-27
  11. HP / Dominator EFI wiring manual 199R10555 · Holley · vendor-doc · retrieved 2026-10-27

Not yet indexed: fewer than 3 FAQs; more than 40% of specs unverified.