Engine: K20Z1 / K20Z3
Part of the Honda K-series family.
Modeled power and torque
Modelled estimate, not a dyno result.
Modeled estimate, not a dyno measurement. Real results vary with fuel, weather, dyno type and build.
Stock is anchored to the factory rating (197 hp at 7800 rpm, 139 lb-ft at 6200 rpm); the curve shape between peaks is modeled. Intake + exhaust + tune (pump fuel): Typical NA gains come mostly above mid-rpm.
K20Z1 / K20Z3 data
- Load sensing
- MAP speed-density
- O2 sensor
- A/F sensor upstream likely (unconfirmed); press states only exhaust oxygen content
- Closed loop
- closed loop at part load, open loop at high load (generic)
- Block
- aluminium
- Rods / pistons
- Not yet sourced
- Reported limit
- Very wide spread: rod vendor (Hybrid Racing) says ~250-300 whp on stock rods; forum reports of ~550-600 whp on stock K24 bottom ends (forum anecdote, low confidence)
- Factory
- Honda top-feed (Keihin/Denso family; maker not confirmed)
- Impedance
- high (saturated)
- Direct-fit upgrades
- 6 maker-listed
- Knock
- Honda 30530-PRC-003
- MAP / MAF
- Honda 37830-PNC-003
- O2 (upstream)
- Honda 36531-RRA-013 (replaces 36531-RRA-003)
Platform background
The RSX (Integra DC5 elsewhere) introduced the K-series to North America. The base car has the 160 hp K20A3 with a dual-stage intake and intake-only VTEC; the Type-S has the 200 hp K20A2 with VTEC on both cams switching above 5800 rpm and a 6-speed. A 2005-06 refresh brought the K20Z1. The RSX is the reference donor for most K-swaps: engine, PCM, harness, transmission and front subframe.
Factory ECU
- 2.0 L DOHC i-VTEC (K20A3), 160 hp @ 6500 rpm, 141 lb-ft @ 4000 rpm
- Intake-only VTEC, dual-stage intake manifold switching at 4600 rpm
- 2.0 L DOHC i-VTEC (K20A2), 200 hp @ 7400 rpm, 142 lb-ft @ 6000 rpm
- VTEC on intake and exhaust above 5800 rpm
Intake cam phasing over 50 degrees, controlled from cam position, ignition timing, exhaust O2 and throttle position
Sourced4Load sensing is reported as MAP-based speed-density with no MAF on the K20A2. Swapping an RSX PCM between cars needs the matching immobilizer or a calibration that addresses it.
Factory ECU: harness cross-reference
From the factory ECU each listed harness plugs into. The factory ECU is unplugged, not modified. Check the label and part number on your own ECU before ordering.
- ECU family
- Honda 37820-PRB (Type S) / 37820-PND (base) family
- Applies to
- Integra DC5 / RSX 2005-06; manual
- Not for
- automatic; multiplexed gauge/AC request features unsupported
Facelift 05-06 part numbers not confirmed; see for 02-04 family.
- ECU family
- Honda K-series (PRB)
- Applies to
- 2005-06 RSX manual
Single listing example.
Factory ECU pinout
Each connector face drawn from the OEM service manual's pin data, with every terminal's function and wire colour where the manual prints it.
Honda K-series ECM/PCM, 2005-06 Acura RSX (K20Z1 / K20A3)
The 2005-06 Acura RSX (K20Z1 Type S and K20A3 base) uses a Honda ECM (manual) or PCM (automatic) on the same five connector shells as 2002-04 cars, A (31P), B (24P), C (22P), D (17P) and E (31P), but with a re-assigned pinout. C and D are fitted on automatic cars only. 125 cavities in total.
2005-2006 · US · 5 connectors, 125 cavities · 88 terminals sourced
Looking into the ECU's connector. The harness plug seen from its wire side has the same layout.
How the OEM figure is oriented
The OEM figure is captioned 'Wire side of female terminals': the harness plug seen from the wire-entry side, lock boss up, terminal 1 at top left. That orientation matches looking into the ECM/PCM header, so the cells are stored as printed and tagged ecu-side; mirror horizontally for the plug's mating face.| Pin | Function | Type | Wire | Notes |
|---|---|---|---|---|
| 1 | Knock sensor (KS) | knock sensor signal | RED/BLU | |
| 2 | Power source, ignition switched (IGP2) | 12 V switched supply | YEL/BLK | |
| 3 | Power source, ignition switched (IGP1) | 12 V switched supply | YEL/BLK | |
| 4 | Power ground (PG2) | chassis ground | BLK | |
| 5 | Power ground (PG1) | chassis ground | BLK | |
| 6 | Camshaft position sensor B (CMPB) | cam position pulses | GRN | |
| 7 | Crankshaft position sensor (CKP) | crank position pulses | BLU | |
| 8 | Logic ground (LG2) | ECM logic ground | BRN/YEL | |
| 9 | Logic ground (LG1) | ECM logic ground | BRN/YEL | |
| 10 | A/F sensor heater control (AFSHTC) | low-side heater driver | BLK/WHT | |
| 11 | Intake manifold runner control solenoid valve (IMT / IMRC) | solenoid driver (switches at 4,700 rpm) | RED/BLU | K20A3 engine only (manual footnote). |
| 12 | Idle air control valve (IACV) | duty-controlled driver | BLK/RED | |
| 13 | Ignition coil No. 4 pulse (IGPLS4) | coil trigger pulse (coil-on-plug with igniter) | BRN | |
| 14 | Ignition coil No. 3 pulse (IGPLS3) | coil trigger pulse (coil-on-plug with igniter) | WHT/BLU | |
| 15 | Ignition coil No. 2 pulse (IGPLS2) | coil trigger pulse (coil-on-plug with igniter) | BLU/RED | |
| 16 | Ignition coil No. 1 pulse (IGPLS1) | coil trigger pulse (coil-on-plug with igniter) | YEL/GRN | |
| 18 | Output shaft (countershaft) speed sensor (NC) | speed pulses | BLU | Printed without an A/T footnote in the 2005-2006 table. |
| 19 | Camshaft position sensor A (CMPA) | cam position pulses | BLU/WHT | |
| 20 | Sensor 5 V supply (VCC2) | 5 V reference | YEL/BLU | |
| 21 | Sensor 5 V supply (VCC1) | 5 V reference | YEL/RED | |
| 23 | Sensor ground (SG2) | sensor ground | GRN/YEL | |
| 24 | Sensor ground (SG1) | sensor ground | GRN/WHT | |
| 28 | A/F (wideband) sensor 1, - side (AFS-) | A/F sensor cell signal | RED/YEL | |
| 29 | Throttle position sensor (TPS) | 0-5 V analog (about 0.5 V closed, 4.8 V wide open) | RED/BLK | |
| 30 | Manifold absolute pressure sensor (MAP) | 0-5 V analog (about 3.0 V key on, 1.0 V at idle) | GRN/RED | |
| 31 | A/F (wideband) sensor 1, + side (AFS+) | A/F sensor cell signal | RED |
Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.
Looking into the ECU's connector. The harness plug seen from its wire side has the same layout.
How the OEM figure is oriented
The OEM figure is captioned 'Wire side of female terminals': the harness plug seen from the wire-entry side, lock boss up, terminal 1 at top left. That orientation matches looking into the ECM/PCM header, so the cells are stored as printed and tagged ecu-side; mirror horizontally for the plug's mating face.| Pin | Function | Type | Wire | Notes |
|---|---|---|---|---|
| 1 | VTC oil control solenoid valve (VTC) | solenoid driver | BLU/WHT | |
| 2 | Injector No. 4 (INJ4) | low-side injector driver | YEL | |
| 3 | Injector No. 3 (INJ3) | low-side injector driver | BLU | |
| 4 | Injector No. 2 (INJ2) | low-side injector driver | RED | |
| 5 | Injector No. 1 (INJ1) | low-side injector driver | BRN | |
| 6 | VTEC solenoid valve (VTS, rocker arm oil control solenoid) | solenoid driver | GRN/YEL | |
| 8 | Engine coolant temperature sensor (ECT) | 0-5 V analog thermistor (about 0.5-4.8 V) | RED/WHT | |
| 10 | Alternator L signal (ALTL) | alternator lamp / L terminal input | WHT/BLU | |
| 11 | VTEC oil pressure switch (VTPSW, rocker arm oil pressure switch) | switch input | BLU/BLK | |
| 13 | Alternator FR signal (ALTF) | alternator field-duty input (0-5 V) | WHT/RED | |
| 17 | Intake air temperature sensor (IAT) | 0-5 V analog thermistor (about 0.5-4.8 V) | RED/YEL | |
| 18 | Alternator control (ALTC) | alternator control output | WHT/GRN | |
| 21 | EVAP canister purge valve (PCS) | duty-controlled solenoid driver | YEL/BLU | |
| 22 | Intake manifold runner control valve position sensor (IMTVPS / IMRCVPS) | 0-5 V analog (about 3.75 V below 4,700 rpm) | RED/YEL | K20A3 engine only (manual footnote). |
Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.
Looking into the ECU's connector. The harness plug seen from its wire side has the same layout.
How the OEM figure is oriented
The OEM figure is captioned 'Wire side of female terminals': the harness plug seen from the wire-entry side, lock boss up, terminal 1 at top left. That orientation matches looking into the ECM/PCM header, so the cells are stored as printed and tagged ecu-side; mirror horizontally for the plug's mating face.| Pin | Function | Type | Wire | Notes |
|---|---|---|---|---|
| 1 | A/T clutch pressure control solenoid valve A (LSA) | current-controlled solenoid driver | RED/BLK | A/T PCM only (connector heading footnote). |
| 2 | Shift solenoid valve C (SHC) | solenoid driver | GRN | A/T PCM only (connector heading footnote). |
| 3 | Shift solenoid valve E (SHE) | solenoid driver | YEL | A/T PCM only (connector heading footnote). |
| 4 | Shift solenoid valve B (SHB) | solenoid driver | GRN/WHT | A/T PCM only (connector heading footnote). |
| 5 | Shift solenoid valve D (SHD) | solenoid driver | GRN/RED | A/T PCM only (connector heading footnote). |
| 6 | Shift solenoid valve A (SHA) | solenoid driver | BLU/BLK | A/T PCM only (connector heading footnote). |
| 7 | A/T clutch pressure control solenoid valve C (LSC) | current-controlled solenoid driver | BLU/YEL | A/T PCM only (connector heading footnote). |
| 9 | Transmission range switch D3 position (ATPD3) | switch input (0 V in D3) | RED | A/T PCM only (connector heading footnote). |
| 10 | 3rd clutch oil pressure switch (OP3SW) | switch input | BLU/WHT | A/T PCM only (connector heading footnote). |
| 12 | Transmission range switch R position (ATPRVS) | switch input (0 V in R) | RED/WHT | A/T PCM only (connector heading footnote). |
| 13 | 2nd clutch oil pressure switch (OP2SW) | switch input | BLU/RED | A/T PCM only (connector heading footnote). |
| 14 | ATF temperature sensor (ATFT) | 0-5 V analog thermistor (about 0.2-4.8 V) | RED/YEL | A/T PCM only (connector heading footnote). |
| 15 | A/T clutch pressure control solenoid valve B (LSB) | current-controlled solenoid driver | BRN/WHT | A/T PCM only (connector heading footnote). |
| 17 | Transmission range switch D position (ATPD) | switch input (0 V in D) | YEL | A/T PCM only (connector heading footnote). |
| 18 | Transmission range switch D/2 position (ATPFWD) | switch input (0 V in D or 2) | BLU/YEL | A/T PCM only (connector heading footnote). |
| 19 | Input shaft (mainshaft) speed sensor (NM) | speed pulses | WHT/RED | A/T PCM only (connector heading footnote). |
| 20 | Transmission range switch N position (ATPN) | switch input (0 V in N) | RED/BLK | A/T PCM only (connector heading footnote). |
Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.
Looking into the ECU's connector. The harness plug seen from its wire side has the same layout.
How the OEM figure is oriented
The OEM figure is captioned 'Wire side of female terminals': the harness plug seen from the wire-entry side, lock boss up, terminal 1 at top left. That orientation matches looking into the ECM/PCM header, so the cells are stored as printed and tagged ecu-side; mirror horizontally for the plug's mating face.| Pin | Function | Type | Wire | Notes |
|---|---|---|---|---|
| 2 | Sequential SportShift mode switch (SMODE) | switch input (0 V in M) | BRN | A/T PCM only (connector heading footnote). |
| 3 | Upshift switch (SUP) | switch input | WHT/BLU | A/T PCM only (connector heading footnote). |
| 5 | Transmission range switch R position (ATPR) | switch input (0 V in R) | WHT | A/T PCM only (connector heading footnote). |
| 6 | Transmission range switch P position (ATPP) | switch input (0 V in P) | BLU/BLK | A/T PCM only (connector heading footnote). |
| 9 | Downshift switch (SDN) | switch input | BRN/WHT | A/T PCM only (connector heading footnote). |
| 12 | Cruise control signal (CCS) | pulse signal to/from cruise control unit | BLU/ORN | A/T PCM only (connector heading footnote). |
Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.
Looking into the ECU's connector. The harness plug seen from its wire side has the same layout.
How the OEM figure is oriented
The OEM figure is captioned 'Wire side of female terminals': the harness plug seen from the wire-entry side, lock boss up, terminal 1 at top left. That orientation matches looking into the ECM/PCM header, so the cells are stored as printed and tagged ecu-side; mirror horizontally for the plug's mating face.| Pin | Function | Type | Wire | Notes |
|---|---|---|---|---|
| 2 | Shift lock solenoid (SLS, A/T) / reverse lock solenoid valve (RVS, K20Z1 M/T) | solenoid driver | — | Honda lists two rows for this cavity: A/T = SLS (SHIFT LOCK SOLENOID), WHT/BLU; K20Z1 engine = RVS (REVERSE LOCK SOLENOID VALVE), YEL/RED. The face view labels it SLS (RVS). Check the car's wire colour. |
| 3 | Logic ground (LG3) | ECM logic ground | BRN/YEL | |
| 4 | Sensor ground (SG3) | sensor ground | PNK | |
| 5 | Sensor 5 V supply (VCC3) | 5 V reference | YEL/BLU | |
| 7 | PGM-FI main relay 1 drive (MRLY); also power source for DTC memory | low-side relay driver | RED/YEL | |
| 8 | A/F sensor heater control relay (AFSHTCR) | low-side relay driver | ORN | |
| 9 | Ignition signal (IG1) | 12 V ignition-switched input | BLK/YEL | |
| 12 | Radiator fan control (FANC) | low-side relay driver | GRN/WHT | |
| 13 | Multiplex control unit communication (SEFMJ) | serial link to multiplex control unit | YEL | |
| 14 | Fuel tank pressure sensor (FTP) | 0-5 V analog (about 2.5 V with fuel cap open) | LT GRN | |
| 15 | Electrical load detector (ELD) | 0-5 V analog (about 0.1-4.8 V) | GRN/RED | |
| 16 | Power steering pressure switch (PSPSW) | switch input | LT GRN/BLK | |
| 17 | Immobilizer fuel pump relay, drives PGM-FI main relay 2 (IMOFPR) | low-side relay driver | GRN/YEL | |
| 18 | A/C clutch relay (ACC) | low-side relay driver | RED | |
| 19 | EVAP canister vent shut valve (VSV) | solenoid driver | LT GRN/RED | |
| 20 | Secondary heated oxygen sensor, sensor 2 (SHO2S) | 0-1 V narrowband O2 signal | WHT/RED | |
| 21 | Secondary HO2S heater control (SO2SHTC) | low-side heater driver | BLK/WHT | |
| 22 | Brake pedal position switch (BKSW) | 12 V switch input (battery voltage when pressed) | WHT/BLK | |
| 23 | K-line, HDS communication (K-LINE) | ISO K-line to DLC | LT BLU | |
| 25 | Engine speed pulse output (NEP) | tach pulse output | BLU | |
| 26 | Vehicle speed sensor output (VSSOUT) | VSS pulse output | BLU/WHT | |
| 27 | Immobilizer code (IMOCD) | immobilizer serial input | RED/BLU | |
| 29 | Service check signal (SCS) | diagnostic input (shorted with the HDS) | BRN | |
| 30 | Write enable signal (WEN) | reprogramming enable input | RED/WHT | |
| 31 | Malfunction indicator lamp (MIL) | low-side lamp driver | GRN/ORN |
Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.
Coverage, year splits and safety
Do not mix years: the shells match the 2002-04 RSX ECM/PCM, but many functions moved (for example the coil drivers move from A27-A30 to A13-A16 and the A/F sensor from A6/A16 to A31/A28, while the crank sensor stays at A7 and the injectors at B2-B5). A 2002-04 harness or ECU will not work pin-for-pin on a 2005-06 car.
Footnoted pins: A11 and B22 (intake runner control) are K20A3 only; E2 is the shift lock solenoid on A/T cars and the reverse lock solenoid on the K20Z1; connectors C and D are A/T only. The catalog row acura-rsx-dc5-base-k20a3 spans 2002-06, so 2002-04 base cars use the 2002-04 RSX entry instead.
Signal descriptions summarise Honda's measuring conditions, not test limits. Disconnect the battery negative before re-pinning, and back-probe only from the wire side with a fine probe; never force a sharp probe into the terminal face or past a seal.
Plug-and-play harness
A plug-in harness built for the Haltech Nexus S3 pinout is listed for this vehicle. The ECU2 follows that published pinout, so the factory ECU is unplugged and the ECU2 plugs into the car's own loom. Nothing is written to the factory ECU. Pin-compatible per the published S3 pinout, not yet fit-tested.
| Maker | Harness | Fits | Link | |
|---|---|---|---|---|
| Nexus S2/S3 Plug n Play Adapter Harness Honda DC5HT-186342 | Integra DC5 / RSX 2005-06; manual | $495Lowest | Maker ↗ | |
![]() | Manual 2005 - 2006 Acura RSXBF29009-S3 | 2005-06 RSX manual | $840 | Maker ↗ |
| Wire-in | Universal flying lead or re-terminated factory harness | Any engine (terminate to ECU2's two Superseal 34 connectors) | Universal harness from $405 | Maker ↗ |
Nexus S2/S3 Plug n Play Adapter Harness Honda DC5
- Plugs into
Honda K20 ECU (2005-06 RSX / DC5 facelift)
- ECU
- Honda 37820-PRB (Type S) / 37820-PND (base) family
- Confidence
- low
Facelift 05-06 part numbers not confirmed; see E-1450 for 02-04 family.
Sources: E-1450
- Fits
- Integra DC5 / RSX 2005-06; manual
- Exclusions
- automatic; multiplexed gauge/AC request features unsupported
- SKU
- HT-186342
- Maker fitment
- Honda Integra DC5 / Acura RSX 05-06; manual only; no factory multiplexed coolant gauge, battery light or AC request
- Maker notes
- (search snippet); kit HT-213301

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 2005 - 2006 Acura RSX
- Plugs into
Honda K-series ECM (2005-06 RSX Type-S K20Z1) · 37820-PRB-A13
- OEM part numbers
- 37820-PRB-A13
- ECU
- Honda K-series (PRB)
- Confidence
- low
Single listing example.
Sources: E-1464
- Fits
- 2005-06 RSX manual
- SKU
- BF29009-S3
- Maker fitment
- Acura RSX (Manual); selector years 2005-2006; SKU label: Manual 2005 - 2006 Acura RSX
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2)
Haltech and Boomslang are trademarks of their respective owners. GAINS is not affiliated with or endorsed by them.
Your GAINS system for this car · pre-release
ECU2 for the RSX DC5
Planned with the same rules as the configurator for this car's 4 cyl · port injection · cable throttle. The factory ECU is unplugged and replaced; nothing is written to it.

- Price TBA
ECU2Engine controller
4 cyl · port injection · cable throttle
Full sequential fuel and spark for this 4-cylinder on a cable throttle, with the wideband built in.
in designEst. availability: April 2027
Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →
Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →
What you get
- A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
- Faults in plain words"Coolant temp sensor open circuit.
- S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
- Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
- GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.
How it wires in
- Haltech S3 plug-in harness1 listed · from $495 USD listHT-186342
- Factory-connector → S3 adapter1 listed · from $840 USD list
- Wire-inAlways possible
Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓
ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.
Swap guides
The K20Z1 / K20Z3 family in other cars
How GAINS approaches the RSX DC5
Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.
- 1Base map and first startplanned
Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.
- 2Lambda targets and VE learningclosed loop on GAINS ECUs
Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.
- 3VTEC crossoverplanned
VTEC engagement is treated as a load and rpm surface where the two cam profiles cross on torque, learned from logs rather than a single fixed rpm.
- 4Cam phasing (VVT)gated
Begin with conservative overlap. Cam targets per load cell are then chosen with torque and knock in mind, keeping idle and cold overlap low for stability. Widening cam authority follows the same evidence-gated path as spark.
- 5Drivability foundationsplanned
Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.
- 6Factory load sensingfactory reference
What the factory ECU measures load with: MAP speed-density (medium confidence)
- 7Wideband sensorhardware
factory O2 type not yet sourced; plan on a Bosch LSU 4.9 for the GAINS ECU's built-in controller
- 8Bottom end and head sealingfactory reference
Reported: Stock rods and especially rod bolts are commonly reported as the first bottom-end limit under boost (vendor and forum consensus); some builders also add sleeves or a block guard because the block is open-deck (single forum opinion). (low confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.
Drivetrain
Chassis integration
Tuning notes
Type-S owners typically start with intake, header and exhaust and a re-optimised VTC/VTEC calibration, then move to K24 bottom ends. Base-car owners converting to a K20A2/K20Z head change the exhaust-side VTEC and should re-map VTC rather than reusing base-car targets.
Popular swaps
Other RSX DC5 guides
GAINS on the RSX DC5
ECU2
Designed so your phone is the laptop, keypad and dash
The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.
Wideband, IMU and logging built in
An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.
Modular, so you buy what the engine needs
This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.
Calibration that keeps learning
Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.
Adaptive tuning strategies
- VE learning closed loop on GAINS ECUs
Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.
- Goal-based lambda targets closed loop on GAINS ECUs
Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.
- Knock protection protection
Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.
- Warm-up, cranking, idle and transient fuel planned
The same learning approach applied to the tables tuners spend hours on after the main map is done.
- Spark advance and boost authority gated
Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.
Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.
GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.
Frequently asked
What engine is in the RSX Type-S?
The K20A2 (2002-04): 200 hp at 7400 rpm with VTEC on both camshafts. 2005-06 cars use the K20Z1.17
When does VTEC engage on the RSX Type-S?
Acura states the high-lift profiles engage above 5800 rpm.4
Does the base RSX have VTEC?
Yes, an economy i-VTEC on the intake side only, plus VTC. The secondary intake rocker locks in at 2200 rpm.4
Does the RSX have an immobilizer?
Yes. Keyless entry with an engine immobilizer is standard.1
Does the RSX have a MAF sensor?
The K20A2 is reported to be speed-density (MAP-based) with no MAF.2
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
- 2002 Acura RSX -- Introduction · Acura (acuranews.com) · press · retrieved 2026-10-25
- 2004 Acura RSX 2.0 K20A2 P0171 (technician discussion) · Diag.net · community · retrieved 2026-10-25
- EGK K-Series Mount Kit (92-95 Civic, 94-01 Integra, Del Sol) · Hasport Performance · vendor-doc · retrieved 2026-10-25
- 2002 Acura RSX Powertrain · American Honda Motor Co. (hondanews.com) · press · retrieved 2026-10-25
- Hasport Performance K-Series Engine Mount Kit (01-05 Civic Non-Si) listing · Hybrid Racing · vendor-doc · retrieved 2026-10-25
- Used 2002 Acura RSX Engine Computers (part-number listings) · PartRequest · community · retrieved 2026-10-25
- Honda K engine · Wikipedia · community · retrieved 2026-10-25
Catalog data and evidence
- Catalog data, not yet expert-reviewed.
- No vehicle photos: illustrations only until licensed imagery is available.
- E-922 Haltech S3 adapter harness page (sourced, high confidence)
- E-9304 K-series harness/ECU xref: H5 (sourced, medium confidence)
- E-934 Boomslang identity (sourced, high confidence)
- E-935 Boomslang S3 catalog size (sourced, high confidence)
- E-900 Haltech Nexus S3 catalog (sourced, high confidence)
- E-941 S3 engine harness availability (inferred, medium confidence)
- E-1450 Honda K20 RSX ECU (reported, low confidence)
- E-1464 RSX ECM (unverified-secondary, low confidence)



