CRX K Swap and Civic EF (1988-91): K20 and K24 Swap Guide

A CRX K swap, or a K swap in the 1988-91 EF Civic, is a well-supported swap, with bolt-in mounts, axles, shifters and conversion harnesses made for the 1988-91 chassis. It takes a K20 or K24 with its own manual gearbox, a mount kit matched to that gearbox, and swap axles. The main hurdles are hood clearance, fuel system conversion, and joining the K-series wiring to the EF dash.Medium12810

Difficulty3/5 · ModerateMedium14109
  • Bolt-in mount kits exist, but Hasport states its EFK kits need cutting and welding, and Innovative's kit calls for welding plus subframe and hood changes.
  • Mounts, axles, intermediate shaft, shifter and cables must all match one K-series gearbox family.
  • A K24, or a K20 on the taller mount setting, needs a raised SiR-style hood to clear.
  • K-series donors are returnless, so the fuel system must be converted to a regulated return setup.
  • The K-series harness must be joined to the EF dash wiring, and dual-point injection cars need an adapter.

At a glance

The key numbers and parts, with the source on each tile.

Mount kitsHasport EFK (EFK2, EFK4, EFK5, EFKAWD) and Innovative 99150Sourced143
Hood
  • K20 on the low Hasport setting fits the stock hood
  • K24 needs an SiR-style hood
Sourced1
AxlesEF swap axles assume the RSX/EP3 manual intermediate shaftSourced25
Recommended engines
  • K20A2, K20A3 or JDM K20A for the simplest parts match
  • K20Z3 or K24A2 with more planning
Wikipedia lists the K20A3 at 160 hp (119 kW) and the K20A2 at 200 hp (149 kW).Sourced · medium138
Original engines (US CRX)

D15B2 dual-point injection (base), D15B6 and D16A6 multi-point (HF, Si)

Sourced · medium14
Fuel system
  • K-series donors are returnless
  • Swap kits add an engine-bay regulator and return
Sourced · medium10
Dash wiring

EF-specific conversion harnesses join the K-series engine harness to the EF dash

Sourced89

Recommended engines

  • K20A2 (RSX Type S / EP3 EU Type R) · High-compression K20 with VTEC on both cams; its RSX/EP3-family gearbox and intermediate shaft are what most EF mount, axle and harness parts are built around.
  • K20A3 (EP3 Si, RSX base) · The RSX base and EP3 Civic Si engine is a lower-cost cable-throttle K20 that shares the same gearbox family, so it works with the same EF mounts, axles and 2002-04 conversion harnesses.
  • K20A (JDM Type R DC5 / FD2 / FN2) · JDM Type R engines rate higher than the US K20s and are a common import pick; check that the gearbox matches your mount variant and that the harness and computer suit your conversion harness.
  • K20Z1 / K20Z3 · The 2006-11 Civic Si K20Z3 brings a six-speed with a factory helical limited-slip differential, but it is drive-by-wire and 2005-06-style wiring is not supported by every EF conversion harness.
  • K24A2 (TSX) · The TSX engine adds the 99 mm stroke for midrange torque; it needs the K24 mount variant, often a taller hood in the EF, and a K24-capable harness and computer.

Mounts

A K swap EF Civic or CRX sits on a mount kit made for the 1988-91 chassis.

Hasport EFK
  • Dual-height brackets and flip mount
  • U62A, U70A, U88A or U94A urethane
Sourced1
Hasport modification
  • Hasport states EFK kits require cutting and welding
  • One retailer says the mounts fit once the factory transmission bracket is removed
Sourced · medium13
Innovative 99150
  • For ED/EF/EE chassis with a manual hydraulic K20 gearbox
  • 75A, 85A or 95A bushings
Sourced4

Hasport's EFK uses dual-height brackets and a flip mount so the engine can be set high or low for axle angle, ground clearance and hood clearance. Hasport states the kits need cutting and welding, so budget fabrication time.1

Innovative's 99150 kit is the other main option. It is listed for ED, EF and EE chassis, manual or automatic, converting to a manual hydraulic K20 gearbox. It calls for welding a self-locating bracket to the frame and modifying the rear subframe and hood, and the maker warns that used mounts cannot be returned.4

Transmission

Pick the gearbox first, because the mount variant follows it.

Hasport variants
  • EFK2: RSX and 2002-11 Civic Si
  • EFK4: 2003-07 Accord and 2004-08 TSX
  • EFK5: 2008-13 Accord, 2009-14 TSX, 2012-15 Civic Si
  • EFKAWD: CR-V and Element
Sourced13
Innovative gearbox limits
  • 02-05 Civic Si, 02-06 RSX or 01-06 Integra Type R manual only
  • Not K24 gearboxes
Sourced4
2006-11 Si six-speedHelical limited-slip differential, 4.765:1 final driveSourced11

Hasport sells EFK2 for RSX and 2002-11 Civic Si boxes, EFK4 for 2003-07 Accord and 2004-08 TSX boxes, EFK5 for 2008-13 Accord, 2009-14 TSX and 2012-15 Civic Si boxes, and EFKAWD for CR-V and Element boxes.13

Innovative's kit is narrower. It fits only manual gearboxes from the 2002-05 Civic Si, 2002-06 RSX and 2001-06 Integra Type R, not K24 gearboxes. A K24 engine on that kit also needs Honda's K24A1 timing-case post mount bracket, which Innovative lists as part 11910-PPA-000.4

Clearance

Hood clearance is the EF's tightest constraint.

K20, low settingFits under the stock hoodHasport EFKSourced1
K20 high setting or K24Needs an SiR-style raised hoodSourced1
Innovative kitHood and rear subframe modification requiredSourced4

On Hasport's kit, a K20 on the lower setting fits under the stock hood, while the high setting, which gives the most ground clearance, calls for an SiR-style hood. A K24 needs that style of hood even on the lower setting.1

Check the radiator and upper hose path, the intake on the driver side, and the header near the firewall. Swap hose kits route the upper hose under the cold air intake and around the transmission counterweights, so fit the intake before you trim anything at the front.Medium6

Cooling

Factory hoses do not join a K-series to the EF radiator.

Hose kits

Hybrid Racing K-swap radiator hoses list 1988-91 Civic and CRX fitment

Sourced6
RadiatorUse a swap radiator or relocate the OEM radiatorSourced6
Hose choice

Sold by head and thermostat housing: K20A/A2/A3/Z1, K20Z3 or K24, or a K20 head with a K24-style housing

Sourced6

Swap hose kits list 1988-91 Civic and CRX fitment and are sold by cylinder head and thermostat housing, because K20A-style and K24-style heads place their coolant outlets differently. Mixed builds, such as a K20 head on a K24 block, need their own variant.6

Decide the radiator before buying hoses. The kit above works with the maker's bolt-in swap radiators or with an OEM radiator that has been relocated. No radiator listed specifically for the EF K swap was found, so confirm mounting tabs and core size with the supplier.Medium6

Fuel

K-series engines come from cars that regulate fuel pressure in the tank and send one line to the rail.

Donor layoutReturnless: regulator in the tank, one line to the engineSourced · medium10
Conversion kit contents

Adjustable regulator, 0-100 psi gauge, -6AN feed and -4AN return lines in the tucked version

Sourced · medium10
EF listing
  • The kit article covers 1992-2000 chassis
  • EF fitment is not listed
Sourced · medium10

Older Honda chassis use a return system, so the swap adds an engine-bay regulator and a return path. Swap fuel kits package a center-port rail connection, adjustable regulator, gauge, filter and lines.Medium10

The kit literature found lists 1992-2000 Civics, Integras and Del Sols, not the EF. Before ordering, trace your EF's feed and return lines at the firewall and confirm the kit's fittings reach them. Set base pressure with a gauge before first start and record it for the calibration.Medium10

Exhaust

Honda mounts the K-series exhaust manifold at the rear of the engine, near the firewall.

Manifold positionRear of the engine, toward the firewall, on the Civic Si and TSXSourced1112
Upstream sensorTSX uses a linear air/fuel sensor ahead of the catalystSourced12

In the short EF and CRX bay that leaves little room between the header, steering rack and floor, so use a header and downpipe shaped for the EF swap rather than donor parts.Medium1112

Plan sensor bungs with the exhaust. Add a wideband oxygen sensor bung for calibration, and keep a catalyst and sensor locations if the car must pass an emissions inspection. One EF harness maker notes that UK-market engine harnesses need their wideband sensor connection adapted to narrowband.Medium128

Electrical

ECU+ PDM / relaysCrank / cam sensorsThrottle (DBW) + pedalInjectorsCoilsEngine sensorsFuel pumpCooling fansGauges / tachStarter / chargingChassis loads
Hybrid Racing EF harness
  • Joins the EF dash harness to a 2002-04 K-series engine harness and computer
  • Keeps tach, coolant and fuel gauges
  • Not for 2005-06 or K24 harnesses
Sourced8
K-Tuned EF harness
  • Handles fuel pump, tach, speedometer, starter signal and oxygen sensors
  • Dual-point injection adapter included
Sourced9
Injection type
  • US base CRX used dual-point injection
  • HF and Si used multi-point
Sourced · medium14

The EF dash wiring was built for a D-series engine, so a conversion harness sits between the chassis and the K-series engine harness. One EF harness is made for 2002-04 K20 engine harnesses and their computers, passes tach, coolant and fuel gauge signals to the factory cluster, and does not support 2005-06 or K24 harnesses.8

Know your original injection type. US base CRXs used dual-point injection while HF and Si models used multi-point, and the chassis wiring differs. One EF harness includes a dual-point adapter in every kit and covers fuel pump, tach, speedometer, starter signal and oxygen sensor circuits.Medium149

Drive-by-wire engines such as the K20Z3 and K24A2 need an electronic pedal and throttle control. The engine itself needs crank and both cam signals, injectors, coils, VTEC and cam-phasing solenoids, manifold pressure, temperatures and the air/fuel sensor, so the engine computer must support all of these.1112

Mount a standalone engine computer and any power distribution module (PDM) in the cabin, under the dash or behind a kick panel, away from heat and water. Use fused, relay- or PDM-switched feeds for the pump, fans and main power. Safety: fuse each new circuit at the source and disconnect the battery before wiring.Low8

Chassis

The EF and CRX are light cars.

SuspensionFour-wheel double wishbone on the 1988-91 Civic and CRXSourced · medium1415
Wheelbase
  • CRX 90.6 in2,301 mm
  • Civic 98.4 in2,500 mm
Sourced · medium1415
Axle ratingEF Level 0 swap axles are described as not a racing axleSourced5

Wikipedia lists US CRX curb weights from about 1,819 lb (825 kg) to 2,174 lb (986 kg) and the Si hatchback at 2,286 lb (1,037 kg). The original US CRX Si engine was rated 105-108 bhp, while the K-series engines in this guide are rated 160 hp (119 kW) and up.Medium141513

Axles carry the launch load. EF swap axles are built for the RSX/EP3 intermediate shaft, and one maker describes its entry set as not a racing axle and gives it no power rating. After install, check clearance at full suspension travel and full steering lock.52

Tuning

Honda's K-series computers calculate load from manifold pressure and trim fuel with an exhaust air/fuel sensor.

Factory load strategy

Speed density from manifold pressure, with an exhaust air/fuel sensor

Sourced1211
Cam control

VTEC on intake only (K20A3) or both cams (K20A2), plus VTC intake phasing

Sourced · medium13
Honda rating, 2006 Civic Si
  • 197 hp at 7,800 rpm and 139 lb-ft at 6,200 rpm
  • 11.0:1 compression
Sourced11

A swap calibration usually keeps that speed-density approach. Start from injector data and displacement, then correct the volumetric efficiency table from wideband logs across the rpm and load range.Medium1211

VTEC changeover and VTC cam angle are calibration choices. Set the VTEC point where the two cam profiles make equal torque and choose cam angles from logged results. Advance ignition only as far as knock monitoring supports; no fixed timing figure is safe for every engine and fuel.Medium13

Parts checklist

Tick what you have; the list is saved in this browser.

0 of 23 ticked (saved in this browser)
Mounts
Transmission
Clearance
Cooling
Fuel
Exhaust
Electrical
Chassis
Tuning
Legal

Order of work

10 stages, in the order most builds follow.

  1. Plan the combination
    Choose engine, gearbox, harness year and engine management together, then order the matching mount variant, axles, intermediate shaft, shifter, hoses and fuel parts.
  2. Choose the hood
    Decide between the low mount setting with the stock hood and the high setting or a K24 with an SiR-style hood.
  3. Prepare the donor
    Check compression and leak-down, and fit fresh seals, clutch and flywheel while the engine is out.
  4. Strip the chassis
    Remove the D-series engine, gearbox, axles, shift linkage, and engine-bay fuel lines. Label the dash-side connectors.
  5. Fabricate and fit mounts
    Cut and weld as the mount maker specifies, paint bare metal, and test-fit before final torque.
  6. Install engine and driveline
    Lower the assembly on a load-leveled hoist, set it on the mounts, then fit the intermediate shaft, axles, shifter, cables and clutch hydraulics.
  7. Plumb fuel and cooling
    Install the regulator, return and gauge, the radiator and swap hoses, and pressure-test both systems.
  8. Wire the engine
    Fit the conversion harness, any injection adapter, pedal and throttle control, fan and pump relays, and fuse every new circuit.
  9. First start and calibration
    Prime oil pressure, confirm fuel pressure and cam/crank sync, start, check for leaks, then build fuel and cam tables from logs.
  10. Shake down and register
    Re-torque mounts and axles after the first drives, then complete emissions, registration and insurance steps for your region.

Common problems

Symptom, cause and the usual fix.

ProblemCauseFix
Hood will not closeK24, or K20 on the high Hasport setting, under the stock hoodUse the low setting with a K20, or fit an SiR-style raised hood as the mount maker specifies.1
Axles do not reach, bind or plunge too farWrong intermediate shaft or mount variant for the axle setUse the RSX/EP3 manual intermediate shaft with EF swap axles and the mount variant they are built for, then check full travel and steering lock.52
Mounts or shifter do not line upMount kit variant or cables ordered for a different gearbox familyMatch mounts, shifter and cables to the transmission; Innovative's kit does not accept K24 gearboxes.147
Gauges or tach dead after the swapConversion harness does not match the engine harness year, or the dual-point adapter is missingUse a harness rated for your engine harness year and fit the dual-point adapter on base cars.89
Lean running or pressure drop under loadReturnless donor supply fed into a return-style chassis without a regulatorInstall an engine-bay regulator with return and confirm pressure with a gauge at idle and under load.Medium10
Overheating or trapped airHose kit does not suit the head and thermostat housing, or the radiator is not relocatedBuy hoses for your exact head and housing combination, relocate the radiator, and bleed from the highest point.Medium6

Frequently asked

What do I need to K-swap an EF Civic?

You need a K-series engine with a matching harness and computer, its manual gearbox, an EF mount kit for that gearbox, swap axles with the RSX/EP3 intermediate shaft, shifter and cables, swap radiator hoses, a fuel return conversion, an EF header, and an EF conversion harness. Plan the hood before buying mounts.Medium126108

Can you K-swap a CRX?

Yes. EF mount kits, axles, hose kits, shifters and conversion harnesses are all listed for the 1988-91 CRX as well as the Civic. The swap follows the same plan as the EF Civic, though the CRX's short bay and hood make engine height and hood choice the first decisions.1679

Does a K24 fit in a CRX or EF Civic?

Yes, with conditions. Hasport's EF kit accepts K24 engines, but a K24 needs an SiR-style hood even on the low setting. Innovative's kit does not accept K24 gearboxes, and a K24 on it needs Honda's K24A1 post mount bracket. Some EF conversion harnesses also exclude K24 engine harnesses.148

Will a K20 fit under the stock CRX hood?

Yes, on Hasport's lower mount setting. Hasport says a K20 fits under the stock hood in that position, while the high setting, which gives more ground clearance, needs an SiR-style hood. Innovative's kit lists hood modification as part of its install, so check the kit you choose.14

What axles do I need for an EF K-swap?

You need EF swap axles built for the RSX/EP3 manual intermediate shaft, not stock EF or donor axles. Hasport sells an EF K-series axle set for that shaft, and another maker's entry set requires Hasport EFK2 mounts. Choose stronger axles for hard launches, sticky tires or forced induction.25

Is a K-swapped CRX street legal?

It can be, depending on where you live. California needs a BAR Referee inspection against the donor vehicle's smog rules, the UK needs a V5C update with evidence, Germany needs an inspector's approval, and Australian states apply VSB 14. This is general information, not legal advice.Medium17181920

Related

Sources

20 sources
  1. EFK K-series Mount Kit (88-91 Civic and CRX) · Hasport Performance · vendor-doc · retrieved 2026-10-27
  2. HP-EFKAX K-series swap axle set (88-91 Civic/CRX, RSX/EP3 manual intermediate shaft) · Hasport Performance · vendor-doc · retrieved 2026-10-27
  3. Hasport K Swap Engine Mount Kit for 88-91 Civic/CRX - retailer listing · Hasport Performance (listing by Hybrid Racing) · vendor-doc · retrieved 2026-10-27
  4. 88-91 Civic/CRX Conversion Mount Kit, K-Series Manual (99150) · Innovative Mounts · vendor-doc · retrieved 2026-10-27
  5. Driveshaft Shop Level 0 K Swap Axles for 88-91 Civic/CRX - retailer listing · The Driveshaft Shop (listing by Hybrid Racing) · vendor-doc · retrieved 2026-10-27
  6. Hybrid Racing K-Swap Radiator Hoses (product page) · Hybrid Racing · vendor-doc · retrieved 2026-10-27
  7. Hybrid Racing K-Swap Bolt-In Shifter and Cable Combo (K24 Trans) · Hybrid Racing · vendor-doc · retrieved 2026-10-27
  8. Hybrid Racing K-Series Conversion Harness for 88-91 Civic/CRX · Hybrid Racing · vendor-doc · retrieved 2026-10-27
  9. K-Tuned K-Swap Conversion Harness, Honda Civic EF / CRX 88-91 - retailer listing · K-Tuned (listing by Tegiwa) · vendor-doc · retrieved 2026-10-27
  10. Tech Talk: Hybrid Racing K-Swap Fuel System Explained · Hybrid Racing · vendor-doc · retrieved 2026-10-27
  11. 2006 Honda Civic Powertrains (press release) · American Honda Motor Co. · oem · retrieved 2026-10-27
  12. 2004 Acura TSX Powertrain (press release, part 2) · American Honda Motor Co. (Acura) · oem · retrieved 2026-10-27
  13. Honda K engine · Wikipedia · reference · retrieved 2026-10-27
  14. Honda CR-X · Wikipedia · reference · retrieved 2026-10-27
  15. Honda Civic (fourth generation) · Wikipedia · reference · retrieved 2026-10-27
  16. Tampering Policy: The EPA Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices under the Clean Air Act (Nov 2020) · US Environmental Protection Agency · standard · retrieved 2026-10-25
  17. Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-25
  18. Change vehicle details on a V5C: what evidence to give · GOV.UK (DVLA) · standard · retrieved 2026-10-25
  19. Strassenverkehrs-Zulassungs-Ordnung (StVZO) section 19: Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
  20. Vehicle Standards Bulletin 14 (VSB 14): National Code of Practice for Light Vehicle Construction and Modification · Australian Government, Department of Infrastructure · standard · retrieved 2026-10-25