Factory specification
Layout, dimensions and factory hardware, each with its source.
Facts tagged “Researched, unverified” come from our engine catalog without a cited source yet.
Jdm K20A Type R horsepower and torque
Ratings as the manufacturer published them, with their basis. They are not GAINS measurements or tuning results.
- EP3 JDM Civic Type R: 215 PS @8000, 202 Nm @7000, CR 11.5212 hp
- FD2 Civic Type R (2007-11): 225 PS @8000, 215 Nm @6100, CR 11.7, limit 8600221 hp
- FN2 EU Civic Type R is K20Z4: 201 PS @7800, 193 Nm @5600, CR 11.0, redline 8000198 hp
Jdm K20A Type R firing order
Jdm K20A Type R injectors
The factory injector, then direct-fit upgrades the makers list for this engine.
Factory injector
Direct-fit upgrades
Sets the maker lists for this engine. Fit is the maker’s own statement; flow is the maker’s rating and test basis.
| Injector | Flow | Fit |
|---|---|---|
| Fuel Injector Clinic FIC 650cc High-Z set · is116-0650hMedium9 | 650 cc/min at 43.5 psi (3 bar), CF-16B fluid 90 F (maker) | Needs adapter USCAR-to-Honda OBD2 plug adapters PADPUtoH4 (optional) or solder-in pigtails PGTUSC4 (included) |
| Injector Dynamics ID1050-XDS · 1050.48.14.14.4Low4567 | 1065 cc/min at 3.0 bar, gasoline 52 C (maker) | Needs adapter USCAR-to-Honda OBD2/K-series plug adapters (ID connector is USCAR; adapters sold separately per retailer listings E-1238) |
Jdm K20A Type R swap
Swap guides that recommend this engine or its family. Each guide covers mounts, transmission, fuel, wiring, tuning and the law, with sources.
Sensors
Factory sensors by role: part numbers, signal type and fitment years.
| Sensor | OEM part numbers | Type / signal | Years and markets |
|---|---|---|---|
| Knock | Honda 30530-PRB-A01 (DC5/EP3) | Honda 30530-PRC-003 (FD2, per retail listing)Low confidence8 | knock sensor | JDM DC5 2001-06 / EP3 Type R per retailer; FD2 per eBay listingNot from a Honda catalogue; verify by frame number. |
| MAP | Not yet sourcedResearched, unverified | not found | JDMJDM catalogue not accessed. |
| MAF | Not yet sourcedResearched, unverified | none listed in OEM catalogue (speed-density, MAP-based) | Inferred from K20 family. |
| O2 (upstream) | Not yet sourcedResearched, unverified | not found | JDM |
Ignition and triggers
Tuning notes
Factory load sensing
The factory ECU measures load by MAP speed-density. JDM DC5/FD2 and EU FN2 not covered by any OEM/press source read; strategy assumed same as K20A2 but not sourced. Leave for follow-up (Honda JP factbook).Low1
Injector drive
Factory injector impedance: high (saturated). Connector: Honda OBD2 / K-series.Low5
Driver and calibration
High-impedance injectors run from a saturated driver. Any injector change needs new flow and dead-time data in the calibration. Researched, unverified
Known limits (reported)
Stock rods and especially rod bolts are commonly reported as the first bottom-end limit under boost (vendor and forum consensus); some builders also add sleeves or a block guard because the block is open-deck (single forum opinion).Low23
Common first upgrades (reported)
Builders most often report upgrading: forged rods with upgraded bolts (vendor/forum).Low23
Valvetrain, factory engine management and weak points across every generation are on the Honda K-series guide.
Vehicles with the K20A (JDM Type R DC5 / FD2 / FN2)
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
9 sources
- Honda K20A2/A3 load sensing (E-824) · acuranews.com · oem · retrieved 2026-10-25
- Honda K-series internals (E-1035) · en.wikipedia.org · reference · retrieved 2026-10-25
- Honda K-series limits (E-1036) · hybrid-racing.com · vendor-doc · retrieved 2026-10-25
- Injector aftermarket fitment (E-1200) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injectors / ID1050-XDS fitment (E-1230) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injector Dynamics ID1050-XDS fitment table (E-1260) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injector Dynamics ID1050-XDS fitment table (E-1290) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- JDM K20A knock sensor (E-1362) · hybrid-racing.com · vendor-doc · retrieved 2026-10-25
- fuelinjectorclinic.com product listing · fuelinjectorclinic.com · vendor-doc · retrieved 2026-10-25
Evidence ids (E-…) refer to our research register; each records the source, date and confidence.



