Compression ratio (static and dynamic)

CRstatic compression ratiodynamic compression ratioSCRDCReffective compression ratio

Compression ratio is the ratio of total cylinder volume with the piston at bottom dead center to the volume left at top dead center. Static compression ratio uses full geometry; dynamic compression ratio counts only the stroke after the intake valve closes, which better reflects actual cylinder pressure and knock tendency.12

How it works

Static compression ratio is fixed by geometry: swept volume plus clearance volume, divided by clearance volume.

Clearance volume includes the combustion chamber, head gasket thickness, piston dome or dish and the gap between piston and deck.12

Higher compression raises theoretical thermal efficiency, because the gas expands further after combustion. Heywood shows efficiency gains that shrink as ratio rises. The limit is knock: higher compression heats the end gas and raises knock tendency.1

The cylinder only starts compressing once the intake valve closes, usually after bottom dead center. Dynamic compression ratio uses the cylinder volume at intake valve closing instead of at bottom dead center, so it is always lower than static. Later closing gives lower dynamic compression.Medium12

Variable cam timing changes intake closing and so changes effective compression while the engine runs. Some engines use deliberately late intake closing, often called Atkinson or Miller operation, with a high static ratio for efficiency.Medium13

In tuning

Compression ratio sets how much spark advance and boost the fuel tolerates.

Higher ratio or higher boost moves the knock limit, so higher-octane fuel or a lower boost target may be needed.12

Changing cams, head gasket thickness, pistons or machining the head or block changes compression. Measure and calculate the result before calibrating; do not assume a published figure after engine work.Medium2

Formula and worked example

CR = (V_d + V_c) / V_c
CR
static compression ratio
V_d
swept (displaced) volume of one cylindercc
V_c
clearance volume at top dead centercc
12

Try it

mm
mm
cc
mm
mm
mm

Negative if the piston pops up above the deck.

cc

Dish and valve reliefs positive, dome negative.

mm
°

Result

Static compression ratio9.44 :1
Clearance volume59.2 cc
Swept volume per cylinder499.6 cc

Planning estimate from the formula below, not a measurement.

Open the full compression ratio calculator →

Myths vs facts

Myth Higher compression always means more power.

Fact Efficiency gains shrink at high ratios, and knock may force retarded timing that removes the gain on a given fuel.1

Myth Static compression tells you everything.

Fact Cam timing changes when compression actually starts. Two engines with the same static ratio can have very different cylinder pressures.Medium12

Myth Compression testing gauges read compression ratio.

Fact Cranking pressure depends on cam timing, cranking speed and sealing. It is a health check, not a measure of geometric ratio.Low2

Frequently asked

How do you calculate compression ratio?

Add the swept volume of one cylinder to the clearance volume at top dead center, then divide by the clearance volume. Clearance volume includes the chamber, gasket, deck clearance and piston dome or dish. A cylinder sweeping 500 cc with 50 cc of clearance volume gives 550 / 50 = 11.0:1.12

What is dynamic compression ratio?

Dynamic compression ratio measures compression from the point the intake valve closes rather than bottom dead center. Because the valve closes after bottom dead center, part of the stroke does not compress the charge, so dynamic ratio is lower than static. It depends on cam timing and connecting rod geometry.Medium12

Does higher compression make more power?

Higher compression improves thermal efficiency, so it can raise torque if the fuel resists knock well enough to keep good ignition timing. Gains shrink as ratio increases. On fuel with too little octane, the engine must retard timing, which can cancel the benefit.1

What compression ratio is best for a turbo engine?

There is no single number. Boosted engines usually use lower static compression than naturally aspirated engines on the same fuel, because boost raises cylinder pressure further. The right choice depends on fuel octane, boost target, charge cooling, cam timing and combustion chamber design.Medium12

Used in these guides

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Internal Combustion Engine Fundamentals, 2nd edition (J. B. Heywood) · McGraw-Hill Education · book · retrieved 2026-10-25
  2. Compression ratio · Wikipedia · reference · retrieved 2026-10-25
  3. Variable valve timing · Wikipedia · reference · retrieved 2026-10-25