LS Swap C10 Square Body (1973-87): LS and LT Swap Guide

An LS swap C10 puts a GM Gen III/IV LS V8 (most often a junkyard 5.3 or 6.0 truck engine) or a Gen V LT into a 1973-87 square-body truck, and bolt-in mounts, swap oil pans, headers and crossmembers are sold for both. The main jobs are oil pan clearance, matching the transmission and flexplate to the crank, a fuel-injection fuel system, and an engine harness and controller that match the engine generation.Medium16182122237

Difficulty3/5 · ModerateMedium1662142331
  • The bay is roomy and bolt-in LS and LT mounts exist for 2WD C10 and 4WD K10 frames.
  • Oil pan choice decides clearance: use a pan sold for the swap rather than a car or truck pan picked at random.
  • LS engines with pre-1998-style automatics (TH350, TH400, 700R4) need a crank or flexplate spacer; LT engines need 8-bolt flexplates.
  • The engine harness and controller must match the engine generation (24x Gen III, 58x Gen IV, Gen V LT).
  • LT direct injection needs a controller that runs the high-pressure pump; truck LS and LT engines may need an Active Fuel Management plan.

At a glance

The key numbers and parts, with the source on each tile.

LS engine options and GM ratings
ItemPowerTorque
5.3 LM7270-295 hp—
6.0 LQ4300-335 hp—
6.0 LQ9345 hp—
6.2 LS3430 hp424 lb-ft575 N·m
Sourced1
LT engine options and GM ratings
ItemPowerTorque
LT1 6.2 L455-460 hp—
L86 6.2 L420 hp460 lb-ft624 N·m
L83 5.3 L355 hp383 lb-ft519 N·m
Sourced1
LS mounts
  • Bolt-in LS swap engine plates for 1973-87 GM trucks reuse the stock small-block clamshell mounts
  • LS/LT bracket kits are listed for 1973-87 C10/C20 2WD
Sourced · medium1617
LS oil pan

2WD: rear-sump swap pan such as Holley 302-1 (paired with the truck mount plate). 4WD K10: Holley 302-4 pan built for the K-truck front axle

Sourced · medium161819
LS fuel system
  • Port injection at about 58 psi
  • Most swaps run a return-style regulator, 6AN feed and return, and a pump around 255 lph for most builds
Sourced · medium2224
LT fuel system
  • Direct injection with a cam-driven high-pressure pump
  • GM's LT1 control system expects a returnless low-pressure supply
Sourced31
Transmissions
  • LS: 1998-and-later GM automatics bolt up directly
  • TH350, TH400, 700R4 and Powerglide need a spacer. LT: GM LT bellhousing kit for 1996-and-later 4L60-family, 8-bolt flexplate
Sourced · medium214
Controller
  • 24x Gen III (to 2006 trucks) and 58x Gen IV (2007+ trucks, LS3) need matching harness and controller
  • Gen V LT needs its own
Sourced · medium23
California route

GM E-ROD LT1 under CARB EO D-126-46: 1995-and-older vehicles up to 4,500 lb test weight (5,725 lb GVWR)

Sourced10

Recommended engines

  • 5.3 LM7 / L59 / LY5 (Gen III/IV truck) · The cheapest common LS swap: 5.3 L Gen III/IV truck engines rated 270-295 hp (LM7) are plentiful from scrapped trucks, use a 6-bolt crank and port injection, and run a simple 58 psi return-style fuel system.
  • 6.0 LQ4 / LQ9 / LY6 / L96 (truck) · 6.0 L iron-block truck engines (LQ4 300-335 hp, LQ9 345 hp) give more displacement for a working truck at junkyard prices.
  • LS3 / L99 · 6.2 L aluminium Gen IV engine rated 430 hp in the Corvette, sold as a crate engine with GM standalone controller kits; 58x crank signal.
  • LT1 (Gen V) · 6.2 L direct-injection Gen V crate engine sold with GM controller kits, and as the E-ROD package with a CARB executive order for 1995-and-older vehicles.
  • L83 5.3 / L86 6.2 (Gen V truck) · Plentiful 2014-up Gen V truck engines (5.3 L L83, 6.2 L L86); direct injection and Active Fuel Management add fuel-system and calibration work.

Mounts

LS mount plate (one maker)

Holley LS swap engine plates for 1973-87 Chevrolet/GMC trucks work with stock small-block clamshell mounts and Hooker BlackHeart headers

Sourced · medium16
LS/LT bracket kit

Hooker BlackHeart LS/LT swap mount bracket kit listed for 1973-87 C10/C20 2WD

Sourced · medium17
LT mount kit contents (one maker)
  • Two OE-style rubber mounts, two steel clamshell upper mounts, hardware
  • Fits 2WD and 4WD
Sourced · medium6
C10 vs K10

Separate Gen V LT mounts are listed for 2WD C10 and 4WD K10 frames

Sourced · medium7

LS mounts

For an LS swap C10 the simplest route is a pair of swap plates or brackets that bolt to the LS block and sit on the truck's original small-block clamshell mounts and frame stands. Pick the plate and oil pan as a pair, because the maker sets engine height and pan clearance together.Medium1617

LT mounts

Gen V LT engines use their own mount kits. One kit keeps the original small-block crank position, so steering, crossmember and driveline geometry stay close to stock.Medium6

For an LT swap C10, bolt-in mounts replace the small-block brackets on the factory frame stands. One kit keeps the original small-block crank position, so steering, crossmember and driveline geometry stay close to stock.Medium6

Order mounts for your frame. 4WD K10 trucks use different mounts from 2WD C10s because of the front axle and transfer case.Medium7

Transmission

LS crank flange

Sits about 10 mm shallower than earlier small-block Chevy cranks relative to the bellhousing flange

Sourced · medium21
LS behind older automatics
  • TH350, TH400, 200-4R, 700R4/4L60 and Powerglide need a spacer
  • 1998-and-later automatics do not
Sourced · medium21
Crank flange
  • Gen V LT engines use an 8-bolt crankshaft flange
  • LS 6-bolt flexplate kits do not fit
Sourced · medium48
Older automatics
  • LT flexplates are offered for TH350, TH400, 700R4, 4L60E and 4L80E
  • Non-LT converters need a snout adapter
Sourced · medium8

LS transmissions

An LS bolts to the small-block Chevy bellhousing pattern, so the truck's TH350, TH400 or 700R4 can stay. Because the LS crank flange sits about 10 mm shallower, those older automatics need a crankshaft or flexplate spacer so the converter snout is supported; 1998-and-later GM automatics such as the 4L60E and 4L80E bolt up without one.Medium21

Electronic automatics (4L60E, 4L80E) need a controller that shifts them: a Gen III PCM can run both engine and transmission, while Gen IV engines normally pair a separate ECM and TCM. Swap crossmembers are listed per transmission family.Medium2317

GM sells an LT bellhousing kit that lets 1996-and-later 4L60-family automatics bolt to a Gen V engine, used with its 8-bolt flexplate kit. LS-era 4L60 flexplate kits are listed as not fitting the LT1.Medium4

Older three-speed and four-speed GM automatics can work with an LT-specific flexplate and either an LS/LT-style converter or a converter snout adapter. Check converter bolt pattern before ordering.Medium8

If the mount kit moves the transmission forward, re-measure the driveshaft and check the shifter linkage and crossmember position. One kit moves it 0.5 in (13 mm).Medium6

Clearance

2WD LS pan
  • Holley 302-1: rear-sump cast pan for GM rear-drive vehicles originally fitted with a small- or big-block Chevy
  • Max stroke 4.25 in
  • Kit includes baffle and pickup
Sourced · medium18
4WD LS pan

Holley 302-4: built for the 1973-87 K10/K20/K30 chassis and other 4WD LS swaps

Sourced · medium19
Oil pan

The hardest part of an early LT1 truck swap: a Corvette dry-sump pan's drain plug hit the K-member, and a truck pan sat too low

Sourced · medium9

LS oil pans

Factory LS car and truck pans were designed for other crossmembers and steering, so a C10 swap uses a swap pan. On 2WD trucks the rear-sump pan sold with the truck mount plate is the usual pairing; 4WD K10 trucks need a pan shaped around the front differential.Medium161819

Use an oil pan sold for the LT truck swap. The first documented LT1 truck swap found that neither the Corvette nor the full-size truck pan fit cleanly, which is why swap-specific pans exist.Medium96

Check the high-pressure fuel pump at the back of the valley and the intake against the cowl and hood. Leave service access to the pump and its lines.Low1

Cooling

Truck accessory drives keep the water pump, alternator and belt layout designed for a pickup's radiator position.

Accessory drive

A 2014 GM truck front accessory drive was used in an early LT1 truck swap

Sourced · medium9

Match radiator inlet and outlet sides to the water pump you use.Low9

Run electric fans with engine-computer control or a well-sized mechanical fan with shroud, and size the radiator for towing if the truck will work.Low3

Fuel

LS fuel pressureAbout 58 psi at the rail for LS applicationsSourced · medium2224
LS swap filter-regulator

Corvette-style 58 psi filter-regulators are sold for LS swaps and need a return line to work

Sourced · medium24
Low-pressure side

GM's LT1 control system is intended for a returnless fuel system and includes a fuel line pressure sensor

Sourced · medium3
High-pressure side
  • Cam-driven mechanical pump
  • LSX Magazine quoted about 2,200 psi152 bar
Sourced · medium19

LS fuel

A carbureted square body has a low-pressure pump and no return line. An LS needs an electric in-tank pump, about 58 psi at the rail, and usually a return-style regulator, which lets you adjust and diagnose pressure easily. PSI Conversion recommends 6AN feed and return lines and a 255 lph pump for most builds.Medium2224

Direct injection splits the system in two. The in-tank pump supplies a low-pressure feed that the engine computer monitors, and a cam-driven pump on the engine raises it to injection pressure.Medium31

Follow the controller kit's documented supply pressure and flow rather than a number from another engine. GM designed its LT1 control system around a returnless supply, so a return-style regulator is not needed.Medium3

Exhaust

LS swap headers

Long-tube LS swap headers are listed for 1973-87 C10/C20 2WD with 1-3/4 in and 1-7/8 in primaries

Sourced · medium20
Exhaust ports
  • LT1 ports needed custom manifolds in the 2015 prototype
  • Swap headers are now listed
Sourced · medium97
Dual exhaustTrue-dual kits are listed for 1973-87 C10 with LS and LT enginesSourced · medium7

LS exhaust

Truck LS exhaust manifolds rarely clear the C10 frame and steering box, so most swaps use swap headers designed with the mount plates. Check starter and steering-box clearance on your frame before ordering.Medium2016

Swap-specific LT headers and mid-length headers now exist for C/K10 trucks, so custom manifolds are optional. Choose headers that clear the steering box and starter on your frame type.Medium7

Keep catalysts and oxygen sensor positions from the emissions package if the truck must pass inspection.Medium10

Electrical

ECU+ PDM / relaysCrank / cam sensorsThrottle (DBW) + pedalInjectorsCoilsEngine sensorsFuel pumpCooling fansGauges / tachStarter / chargingChassis loads
24x vs 58x

24x: Gen III LS1/LS6/LQ4/LQ9 and 4.8/5.3/6.0 trucks to 2006, cam sensor at the rear. 58x: Gen IV LS2/LS3/L92 and 2007+ trucks, cam sensor in the front cover

Sourced · medium23
GM LS controller kits

Standalone controller kits are sold for Gen IV LS crate engines (for example 19540147, listed as superseding 19354328)

Low confidence25
Controller requirements

Direct-injector and high-pressure pump drivers, cam phaser control, drive-by-wire throttle and a low-side fuel pressure input

Sourced · medium13
Swap harnessesStandalone Gen V engine harnesses are sold for square-body swapsSourced · medium7

LS wiring

The harness and controller must match the engine. Gen III engines use a 24x crank wheel and usually a single PCM; Gen IV engines use 58x and a separate ECM and TCM. They are not interchangeable without a signal converter, so buy the harness for the exact engine and controller you will run.Medium23

Drive-by-cable or drive-by-wire

Only Gen III controllers support a cable throttle, so a Gen IV LS with a cable throttle body needs a different approach, such as a 24x crank wheel conversion. Decide throttle type before buying the harness.Medium23

A Gen V engine needs a controller that reads its crank trigger and cam sync, drives direct injectors and the high-pressure pump, runs the cam phaser for variable valve timing, and controls the drive-by-wire throttle with its matching pedal.Medium13

Truck L83 and L86 engines have Active Fuel Management, and L84/L87 engines have Dynamic Fuel Management. Decide whether to disable it in calibration or convert the valvetrain before buying parts.Medium1

On the truck side, wire the fuel pump control and pressure sensor, cooling fans, an A/C compressor request, and tach, temperature and oil-pressure signals for the factory gauges. Use a fused main feed and check cable sizes with the wire gauge calculator.Low37

Chassis

A 1973-87 truck was designed around carbureted small-blocks and big-blocks.

Generation span
  • Third-generation C/K built from 1973
  • Renamed R/V from 1987 and phased out through 1991
Sourced · medium2

Check brakes, rear axle and driveshaft against the LT's torque before adding it.Low21

4WD K10 trucks add a transfer case and front axle, which change mount choice and oil pan clearance compared with a 2WD C10.Medium72

Tuning

Load sensingGM LT1 controller kits include a MAF sensorLow confidence5
GM controller kits
  • Kits 19418585/87/89/91 cover 2021-and-older LT1 engines
  • 19433246/47 cover 2022-and-newer
Sourced · medium3

LS tuning

A junkyard LS controller carries the donor vehicle's calibration, so it must be edited for the swap (anti-theft, transmission, fans and sensors) or replaced with a standalone controller. Calibrate on a wideband before driving hard.Low323

A GM controller kit or E-ROD package arrives calibrated for the engine, which avoids building a direct-injection calibration from nothing. Junkyard truck engines with their own computer need the calibration edited for the swap.Medium310

Log with a wideband oxygen sensor, verify fuel pressure on both sides of the system, and confirm knock control is active. Make ignition timing changes in small monitored steps only.Low3

Parts checklist

Tick what you have; the list is saved in this browser.

0 of 23 ticked (saved in this browser)
Mounts
Transmission
Clearance
Cooling
Fuel
Exhaust
Electrical
Chassis
Tuning
Legal

Order of work

8 stages, in the order most builds follow.

  1. Check legality and GVWR
    Confirm local engine-change rules and, in California, whether the truck's GVWR fits an E-ROD order.
  2. Choose LS or LT, controller and transmission together
    An LS keeps fuel and wiring simpler and costs less; a Gen V LT adds direct injection and an 8-bolt crank. Pick the harness and controller for the exact engine generation.
  3. Remove the old drivetrain
    Pull the engine and transmission, label wiring and fuel lines, and inspect frame mounts and crossmember.
  4. Prepare the engine
    Fit the swap oil pan, mount plates or brackets, flexplate or flywheel (with spacer if needed) and accessory drive on the stand.
  5. Install and align
    Lower the engine onto the mounts, set the transmission crossmember, check driveline angle and measure for the driveshaft.
  6. Fuel, cooling and exhaust
    Install the EFI pump and the right regulator layout (return-style LS or returnless LT), plumb the radiator and fit swap headers.
  7. Wire the controller and truck
    Connect power, grounds, fuel pump, fans, throttle pedal, transmission control and gauge signals; check fuses and cable sizes.
  8. Start and calibrate
    Prime and leak-check fuel, confirm oil pressure, then calibrate with a wideband before load testing.

Common problems

Symptom, cause and the usual fix.

ProblemCauseFix
Oil pan hits the crossmember or hangs too lowUsing a car or full-size truck pan not designed for the square-body crossmember.Use the swap pan matched to your mount plates: a rear-sump swap pan on 2WD, a K-truck pan on 4WD.Medium16199
Torque converter does not seat or the snout is unsupported (LS)LS crank flange is about 10 mm shallower than an old small-block's; TH350, TH400 and 700R4 converters were sized for the old depth.Fit an LS crank or flexplate spacer, or use a 1998-and-later automatic.Medium21
Flexplate will not bolt to the crank (LT)Gen V LT engines use an 8-bolt crank flange; LS 6-bolt flexplates do not fit.Use an LT-specific 8-bolt flexplate or GM's LT installation kit.48
Engine cranks but will not start on a junkyard harnessHarness or controller does not match the engine's 24x or 58x crank signal, or anti-theft is still active.Match harness, controller and engine generation, and disable anti-theft in the calibration.Medium23
Engine stumbles or sets fuel pressure codesLS: low pressure or no return line for the regulator. LT: low-side supply does not meet the controller kit's requirement.LS: confirm about 58 psi at the rail and a working return. LT: follow the kit's returnless supply specification.Medium22243
Driveshaft too long after the swapMount kit or transmission choice moved the transmission.Measure the new length with the truck at ride height and shorten or replace the driveshaft.Medium6

Frequently asked

What do you need to LS swap a C10?

An LS engine, swap mount plates or brackets for your C10 or K10 frame, a swap oil pan, a transmission with the right flexplate (and a spacer for TH350, TH400 or 700R4), an EFI fuel pump with a 58 psi regulator and return, swap headers, and a harness and controller that match the engine.Medium1618212223

Should I LS or LT swap my square body?

An LS, especially a junkyard 5.3 or 6.0, costs less and uses port injection with a simple 58 psi fuel system. A Gen V LT makes more power per litre but adds direct injection, a high-pressure pump, an 8-bolt crank and a more complex controller. GM's E-ROD LT1 also gives a documented California route for trucks within its weight limit.Medium122310

What oil pan fits an LS swap C10?

Use a swap pan sold with or for your mount plates. On 2WD trucks a rear-sump swap pan such as the Holley 302-1 is the common pairing with the truck mount plate; 4WD K10s need a pan made for the K-truck front axle, such as the Holley 302-4.Medium161819

What transmission bolts to an LS in a C10?

The LS shares the small-block Chevy bellhousing pattern, so TH350, TH400 and 700R4 bolt on with a crank or flexplate spacer, and 1998-and-later automatics like the 4L60E and 4L80E bolt on directly. Electronic automatics need a controller to shift them.Medium2123

Do you need a return fuel line for an LS swap?

Most LS swaps use one: a Corvette-style 58 psi filter-regulator needs a return line to work, and return systems are easy to adjust and diagnose. A returnless setup can work with a drop-in module designed for it. Gen V LT engines are different: GM's LT1 controller system expects a returnless supply.Medium22243

What oil pan fits an LT swap C10?

Use a pan made for the LT truck swap. The first documented LT1 truck swap found that a Corvette pan's drain plug hit the K-member and a full-size truck pan sat too low.Medium96

Can an LS or LT swapped C10 pass smog in California?

This is general information, not legal advice. Engine changes go through a BAR Referee. GM's E-ROD LT1 under CARB EO D-126-46 covers 1995-and-older vehicles up to 5,725 lb GVWR, which gives a documented route; any other swap must match a certified configuration and keep its emissions equipment.Medium101211

Related

Sources

25 sources
  1. General Motors LS-based small-block engine (Gen III, IV and V sections) · Wikipedia · reference · retrieved 2026-10-27
  2. Chevrolet C/K (third generation) · Wikipedia · reference · retrieved 2026-10-25
  3. LT1 engine control system installation instructions (kits 19418585/87/89/91, 19433246/47) · GM / Chevrolet Performance (hosted by JEGS) · oem · retrieved 2026-10-25
  4. Automatic transmission installation kits · Chevrolet Performance · oem · retrieved 2026-10-25
  5. Chevrolet Performance LT1 engine controller kit 19418587 · JEGS (retailer listing of GM kit) · vendor-doc · retrieved 2026-10-25
  6. 1973-1987 Chevy Square Body Truck LT Swap Engine Mount Kit for 2WD/4WD (5510-KIT553EM) · ICT Billet · vendor-doc · retrieved 2026-10-25
  7. 1973-87 Squarebody swap parts · PSI Conversion · vendor-doc · retrieved 2026-10-25
  8. Billet steel LSA / Gen V LT flexplate, 8-bolt · Michigan Motorsports · vendor-doc · retrieved 2026-10-25
  9. Spotted: Is This The First LT1 Swapped C10 In The World? · LSX Magazine · press · retrieved 2026-10-25
  10. Executive Order D-126-46: GM LT1 E-ROD engine kit · California Air Resources Board · standard · retrieved 2026-10-25
  11. Tampering Policy: The EPA's Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices (Nov 2020) · US Environmental Protection Agency · standard · retrieved 2026-10-25
  12. Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-25
  13. Change vehicle details on a V5C registration certificate (log book) · GOV.UK / DVLA · standard · retrieved 2026-10-25
  14. StVZO § 19 Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
  15. VSB 14 National Code of Practice for Light Vehicle Construction and Modification, Section LA: Engines · Queensland Department of Transport and Main Roads · standard · retrieved 2026-10-25
  16. Holley LS swap mount engine plate, Chevrolet/GMC truck 1973-1987 (12621HKR) · CJ Pony Parts (retailer listing of Holley part) · vendor-doc · retrieved 2026-10-27
  17. Hooker BlackHeart LS/LT swap engine mount bracket kit, Chevy C10/C20 73-87 (BHS540) · CJ Pony Parts (retailer listing of Holley/Hooker part) · vendor-doc · retrieved 2026-10-27
  18. Holley 302-1 GM LS swap oil pan · SD Parts (retailer listing of Holley part) · vendor-doc · retrieved 2026-10-27
  19. Holley LS swap oil pan, 4-wheel drive GM truck 1973-87 (302-4) · CJ Pony Parts (retailer listing of Holley part) · vendor-doc · retrieved 2026-10-27
  20. Hooker BlackHeart long tube headers, LS swap, Chevrolet C10 1973-1987 (1-3/4 in and 1-7/8 in) · CJ Pony Parts (retailer listing of Holley/Hooker part) · vendor-doc · retrieved 2026-10-27
  21. Summit Racing Carries Trick Flow's New LS Flexplate Spacer (2015-02-21) · LSX Magazine (Power Automotive Media) · press · retrieved 2026-10-27
  22. LS and LT Swap Fuel System Guide (2026-05-15) · PSI Conversion · vendor-doc · retrieved 2026-10-27
  23. 24x vs 58x Reluctor Differences for LS and LT (2026-05-15) · PSI Conversion · vendor-doc · retrieved 2026-10-27
  24. Holley 162-591 EFI fuel filter regulator, GM return style, 58 psi · JEGS (retailer listing of Holley part) · vendor-doc · retrieved 2026-10-27
  25. Chevrolet Performance 19540147 LS2/LS3 engine controller kit for Gen IV LS crate engines · JEGS (retailer listing of GM kit) · vendor-doc · retrieved 2026-10-27