Coyote Swap Dentside F-100 / F-150 (1973-79): Mounts, Fuel, Wiring and Legal Guide

A Coyote swap into a 1973-79 Dentside F-100 or F-150 is a popular restomod, and fabricators sell bolt-in mount kits for these frames. It takes swap mounts, a tunnel big enough for a modern automatic, a return-style fuel system and complete engine controls. The main hurdles are header and steering-box clearance, the transmission tunnel and wiring a 1970s truck for drive-by-wire.Medium51

Difficulty3/5 · ModerateMedium51
  • The engine bay is roomy, and swap mount kits exist for these frames.
  • The stock transmission tunnel is too small for a 6R80, so 2WD automatic trucks usually need tunnel work.
  • Passenger-side header clearance can require grinding the top of the frame rail.
  • Mustang donors have electric power steering, so the hydraulic steering box needs a separate pump setup.
  • The truck needs a new tank, pump and return system plus complete drive-by-wire engine controls.

At a glance

The key numbers and parts, with the source on each tile.

Best engine for most buildsGen 2 Coyote (2015-17) with a 6R80Port injection only; Gen 3 adds direct injection.Sourced · medium3
Truck-donor option2011-17F-150 5.0Lower compression than the Mustang engine, cast iron manifolds and an external oil cooler.Sourced · medium3
Coyote weightAbout 430 lb measured with flywheel, without water pump195 kgNo reliable published weight was found for the factory 1970s engines it replaces, so no net change is given.Sourced · medium6
Engine widthJust over 29 in valve cover to valve cover737 mmSourced · medium6
Mount approachBolt-in engine and transmission mount kit for the stock frameSourced · medium5
Transmission options

6R80 or 10R80 automatic, or a manual with suitable tunnel clearance

A manual or 4x4 transmission hump clears a 6R80 without cutting.Sourced · medium5
Fuel system

Return-style, 55 psi (3.8 bar), pump of at least 155 L/h at 55 psi

Requirement of Ford Performance's Gen 1 controls package.Sourced1
Steering
  • Keep the hydraulic box and add a pump kit
  • Mustang donors have no steering pump
Sourced · medium5

Recommended engines

  • Coyote Gen 2 · Port injection only, with common 2015-17 Mustang and F-150 donors and a 6R80 automatic behind it; the simplest controls for the money.
  • Coyote Gen 1 · Cheapest donors. The 2011-14 F-150 version has lower compression, cast iron exhaust manifolds and an external oil cooler, which suits a work truck.
  • Coyote Gen 3 · Pairs with the 10R80 and makes the most power, but adds direct injection and 12.0:1 compression, so controls and fuel grade get stricter.

Mounts

A Coyote swap in an F-100 usually uses a bolt-in kit that places the engine and transmission on the stock frame.

Kit contents (typical)Engine mounts plus a transmission mount that set engine positionSourced · medium5
Front suspensionThe documented build kept the stock front suspensionSourced · medium5

Kits differ for 2WD and 4x4 frames and by year, so match the kit to your truck's VIN data before ordering.Medium5

If the truck is getting an aftermarket independent front suspension, use mounts designed for that crossmember instead. Several suspension makers sell Coyote mounts that only fit their own front ends.Low5

Transmission

Most Dentside Coyote swaps use a 6R80 from the donor, or a 10R80 with later engines.

Factory transmissions
  • C4 and C6 three-speed automatics
  • Three- and four-speed manuals
Sourced · medium4
6R80 tunnel fit
  • The stock 2WD automatic tunnel is too small
  • Manual and 4x4 humps have room
Sourced · medium5
Ford Gen 1 controls packageManual transmission onlySourced1

Both are electronically controlled, so they need a transmission controller and a shifter solution. Plan the transmission cooler early; the documented build mounted it under the floor with spacers for airflow.Medium5

Four-wheel-drive trucks need a 4x4 transmission and a transfer case that matches your front and rear driveshaft positions. Measure both shafts after the drivetrain is mounted and have them built to length.Low5

Clearance

The documented swap was a 1971 F-100, one generation older than a Dentside but on a similar frame layout.

Headers
  • Stock Mustang GT headers fit the frame rails
  • The passenger side needed frame-top grinding
Sourced · medium5
Steering boxDriver header cleared the stock box with a small heat shieldSourced · medium5
WidthJust over 29 in737 mmSourced · medium6

Its stock Mustang headers cleared the steering box with a heat shield and needed minor grinding on the passenger frame rail. Expect similar work on a 1973-79 truck.Low5

The four-cam heads are wide, so check the brake master cylinder, steering shaft and inner fenders before final placement. The Coyote's intake sits lower than a carbureted big-block's air cleaner, so hood height is rarely the limit.Low65

Cooling

The documented build fitted a radiator in the stock core support with a high-output electric fan.

Fan control in Ford's Gen 1 package

On at 195 F (91 C), off at 190 F (88 C), inferred from cylinder head temperature

Sourced1
Fan wiringDedicated fan ground of at least 10 AWGSourced1

Coyote donors have no belt-driven fan provision suited to a truck shroud, so plan on electric fans with relays and a degas bottle mounted above the engine's highest coolant point.Medium51

Towing raises cooling demand. If the truck will tow, size the radiator and transmission cooler for it and keep the F-150 engine oil cooler if you used a truck donor.Low3

Fuel

Dentside fuel tanks were built for low-pressure carburetor pumps.

Regulated pressure55 psi, regulator referenced to manifold vacuum3.8 barSourced1
Pump flowAt least 155 L/h (41 US gal/h) at 55 psiSourced1
Factory tanks
  • Behind-seat tank dropped after 1976
  • Bed-mounted tanks followed
Low confidence4

The documented swap fitted a new baffled tank with an in-tank pump suited to the Coyote. That approach avoids pump cavitation, which Ford warns can cause lean stumbles.Medium51

Ford's crate-engine controls expect a return-style system with a vacuum-referenced regulator, AN fittings at the rail and filtration of about 100 micron before and 10 micron after an external pump.1

Exhaust

Exhaust routing on a truck is simpler than on a car because the frame is open underneath.

Header options

Mustang GT headers with minor fitting, cast F-150 manifolds, or swap-specific headers

Sourced · medium53
Oxygen sensor placementMoving sensors from stock locations can require recalibrationSourced1

Run each bank to its own catalyst if the truck must pass an emissions inspection, and keep the oxygen sensors where they sample the whole bank.Medium1

Keep exhaust at least a hand's width from fuel lines, brake lines and wiring, and add heat shields near the steering box.Low5

Electrical

ECU+ PDM / relaysCrank / cam sensorsThrottle (DBW) + pedalInjectorsCoilsEngine sensorsFuel pumpCooling fansGauges / tachStarter / chargingChassis loads
Throttle
  • Drive-by-wire pedal
  • The documented build used an existing firewall hole for one bolt
Sourced · medium5
Keep-alive powerMust be hot at all timesSourced1
Ground qualityUnder 0.1 ohm from battery negative to the chassis ground pointSourced1

A Coyote controller needs crank position, cam feedback for each phased camshaft, eight coil-on-plug coils, eight injectors, the drive-by-wire throttle and pedal, MAF and air temperature, knock sensing and both wideband oxygen sensors. Gen 3 engines also need direct-injection pump and injector control.Medium31

On the truck side, wire switched ignition and start feeds, fuel pump control, the alternator control circuit, fan relays, a tachometer signal and A/C requests. A 1970s cluster has no input for a modern speed sensor, so plan a converter or new gauges. Donor PCMs may also need anti-theft programming.Low1

Chassis

Pre-1976 trucks have drum brakes at all four corners, so a disc conversion belongs in the plan.

Front brakesDiscs replaced four-wheel drums in 1976Sourced · medium4
F-150 introduction1975, as a higher-GVWR version above 6,000 lb2,722 kgSourced · medium4
Power steeringHydraulic box retained with a remote-reservoir pump kitSourced · medium5

The documented build also added power brakes.Medium45

Mustang Coyote donors use electric power steering and have no steering pump. Keeping the truck's hydraulic box means adding a pump kit for the Coyote's accessory drive with a remote reservoir.Medium5

Tuning

A custom intake tube changes how the MAF reads airflow, so the calibration must be corrected for it.

Load sensing
  • MAF in the intake tube
  • The documented build welded a MAF bung into a custom intake
Sourced · medium51
MAF placement guidance

At least 6-8 in (150-200 mm) upstream of the throttle, and not more than 24 in (610 mm)

Sourced1
Fuel gradePremium, 91 octane (AKI) or higher, for Ford's calibrationSourced1

Ford's guidance is a straight section, sensor in the upper half of the tube, and a sensor-to-throttle distance between 6 and 24 in.1

Trucks see long, heavy load at low rpm when towing. Log wideband lambda, knock activity and cam angles under load, and keep spark changes conservative and knock-led. Recheck the speedometer and shift points after any tire or axle ratio change.Low13

Parts checklist

Tick what you have; the list is saved in this browser.

0 of 26 ticked (saved in this browser)
Mounts
Transmission
Clearance
Cooling
Fuel
Exhaust
Electrical
Chassis
Tuning
Legal

Order of work

10 stages, in the order most builds follow.

  1. Choose donor and drivetrain
    Decide on engine generation, transmission and, for 4x4 trucks, transfer case. Buy the mount kit that matches your frame and year.
  2. Strip the truck
    Remove the old engine, transmission, fuel tank and lines, and label any body wiring you will keep.
  3. Fit mounts and test-fit
    Install the mount kit, lower the engine and transmission, and mark any frame grinding or tunnel work.
  4. Tunnel and frame work
    Modify the tunnel if needed, grind header clearance, and refinish bare metal before final installation.
  5. Final install
    Install the engine and transmission with a load leveler, fit the crossmember, then the headers and steering box heat shield.
  6. Fuel system
    Install the new tank and in-tank pump, regulator, return line and inertia switch. Route lines away from heat.
  7. Cooling and steering
    Fit the radiator, fans, degas bottle and transmission cooler, then the power steering pump kit and lines.
  8. Wiring
    Lay out the harness, mount the controller and relays, connect power, grounds, pedal, fans and pump, and verify grounds with a meter.
  9. Driveshafts and first start
    Measure and order driveshafts. Pressure-check fuel, fill fluids, check for codes, start, and bleed the cooling system.
  10. Tune and register
    Correct the calibration for your intake, log under load, then complete the registration and emissions steps for your region.

Common problems

Symptom, cause and the usual fix.

ProblemCauseFix
6R80 will not fit under the floorThe stock 2WD automatic tunnel is too smallTrim and rebuild the tunnel, or use a manual or 4x4 floor hump section.Medium5
Passenger header hits the frame railHeader primary routing over the railGrind a small relief on the top of the rail or use swap-specific headers.Medium5
No power steering after the swapMustang donors use electric steering and have no hydraulic pumpAdd a pump kit on the Coyote accessory drive with a remote reservoir and hoses to the stock box.Medium5
Lean stumble under loadOriginal tank and pickup starving the pump, or pump cavitation from an external pumpFit a baffled tank with an in-tank pump and correct filtration.Medium15
Engine stalls after bumpsIntermittent ignition-run feed to the PCMFeed the run circuit from one reliable ignition switch source and secure the connector.1
Speedometer does not workFactory cluster expects a cable drive that modern transmissions lackAdd a signal converter or fit gauges that read an electronic speed signal.Low1

Frequently asked

Will a Coyote fit in a 1973-79 Ford F-100?

Yes. The Dentside bay has room for the 29 in (737 mm) wide Coyote, and fabricators sell bolt-in engine and transmission mounts for these frames. Expect to grind a little frame-rail clearance for the passenger header, shield the steering box, and modify the tunnel if you run a 6R80 in a 2WD truck.Medium56

Do Mustang GT headers fit an F-100 Coyote swap?

In the documented 1971 F-100 build they did, with caveats. The driver side cleared the stock steering box with a small heat shield, and the passenger side needed grinding on the top of the frame rail. Dentside frames are similar, but check your own truck, or buy swap headers designed for your mount kit.Medium5

Which transmission goes behind a Coyote in a Dentside?

Most builders use the donor's 6R80 automatic or a 10R80 behind later engines. Both need electronic control and more tunnel room than a 2WD automatic floor provides. A manual transmission or 4x4 floor hump already gives that room. Four-wheel-drive trucks also need a matching transfer case and new driveshafts.Medium5

Should I use a Mustang or F-150 Coyote in a truck?

Either works. Mustang engines come with higher compression and tubular headers. The 2011-17 F-150 version has lower compression, cast iron exhaust manifolds and an external oil cooler, which suit towing. Note that Ford's 2015-17 Mustang controls package states it is not for F-150 5.0 engines.Medium32

Is a Coyote-swapped Dentside smog exempt in California?

Only 1973-75 trucks. California exempts gasoline vehicles of model year 1975 and older from Smog Check. A 1976-79 truck with a Coyote is an engine change and needs a BAR Referee inspection based on the donor vehicle's requirements. Federal tampering rules still apply. This is general information, not legal advice.987

What fuel system does a Coyote need in an old truck?

A modern in-tank pump, a vacuum-referenced regulator and a return line. Ford Performance's Gen 1 crate-engine controls specify 55 psi (3.8 bar) and a pump of at least 155 L/h at that pressure. The original carbureted tank cannot do this, so most builds fit a new baffled tank.15

Related

Sources

12 sources
  1. M-6017-A504VB 2011-2014 Coyote 5.0L Crate Engine Controls Pack Instruction Sheet · Ford Performance Parts · oem · retrieved 2026-10-25
  2. M-6017-504V Control Pack, 2015-17 Coyote 5.0L Manual Transmission · Ford Performance Parts · oem · retrieved 2026-10-25
  3. Ford Coyote engine · Wikipedia · reference · retrieved 2026-10-25
  4. Ford F-Series (sixth generation) · Wikipedia · reference · retrieved 2026-10-25
  5. How To Engine Swap: Dropping a Coyote Motor in a Ford F-100 · Street Trucks · press · retrieved 2026-10-25
  6. Ford vs Chevy Comparison: Size, Weight, and HP Per Pound · EngineLabs · press · retrieved 2026-10-25
  7. Tampering Policy: The EPA's Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices under the Clean Air Act · U.S. Environmental Protection Agency · standard · retrieved 2026-10-25
  8. Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-25
  9. Smog Inspections · California Department of Motor Vehicles · standard · retrieved 2026-10-25
  10. Change vehicle details on a V5C registration certificate (log book) · GOV.UK (DVLA) · standard · retrieved 2026-10-25
  11. § 19 StVZO: Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
  12. Vehicle Standards Bulletin 14 (VSB 14): National Code of Practice for Light Vehicle Construction and Modification · Australian Government Department of Infrastructure, Transport, Regional Development, Communications and the Arts · standard · retrieved 2026-10-25