K24 + BMW M DCT swap guide: Honda S2000 (AP1 / AP2)

A K24 with a BMW M DCT (Getrag GS7D36SG) in an S2000 is a proven but advanced swap, best known from time-attack cars. It combines a K-swap mount kit with a K-to-DCT adapter and flywheel, a custom gearbox mount and driveshaft, and tunnel work. The main hurdles are controlling the gearbox: a standalone or retained TCU over CAN, immobilizer status, cut and blip, and track cooling.Medium1239

Difficulty4/5 · HardMedium32911
  • The engine side has complete S2000 K-swap kits, but the dual-clutch side needs a custom gearbox mount, a custom driveshaft with a flange adapter and, on some cars, cutting tunnel bracing.
  • The GS7D36SG relies on CAN messages from the engine computer and chassis; without a gearbox controller and the right inputs it will not shift properly.
  • The donor TCU's immobilizer status and the controller route (retained OEM TCU or replacement controller) must be settled before wiring starts.
  • Calibrating engagement, shifts, downshift blips and safeties is reported to take days.

At a glance

The key numbers and parts, with the source on each tile.

Swap ecosystem
  • Complete S2000 K24 kits for the engine
  • K-to-DCT adapter kits from PMC and Seems Legit Garage
  • Gearbox mount and driveshaft usually custom
Sourced · medium4673
Gearbox
  • Getrag GS7D36SG 7-speed wet dual-clutch (BMW M DCT)
  • Gen 1 from the E9x M3, gen 2 in F-series M cars
Sourced1119
Known build

SuperK S2000 time-attack car: stock TSX K24 with a basic turbo, BMW dual-clutch and a gearbox control unit

Sourced · medium21
Controller options

MaxxECU (built into the ECU), CANTCU (keeps the OEM TCU), HTG GCU (replaces it), SLG direct-wire approach

Sourced · medium911122
Factory torque capacity
  • About 450 lb-ft from the factory per SLG
  • MaxxECU says the M3 TCU may shift to neutral above about 800 Nm
Vendor figures, not BMW ratings.Sourced · medium29
Stock S2000
  • Front mid-engine RWD
  • 6-speed manual
  • Torsen LSD
  • 4.100 final drive
  • 1,274-1,299 kg curb
Sourced · medium16
Builder cost estimate

ASM: the DCT part alone is unlikely to be done for much less than $10k

One vendor's 2021 estimate; depends on ECU, controller and driveshaft.Low confidence3
Immobilizer

The donor TCU may need unlocking or replacement firmware, done by the buyer with the controller maker's own tool

Sourced · medium119

Recommended engines

  • K24A2 (TSX) · The ASM complete S2000 K-swap kit is designed around the USDM K24A2, and the SuperK S2000 time-attack car that runs a BMW dual-clutch uses a stock TSX K24.
  • K24Z (K24Z7 Civic Si) · PMC lists K24Z1 to K24Z7 blocks as compatible with its K-to-GS7D36SG adapter, so a later K24Z works with the dual-clutch if your S2000 mount and intake parts accept it.
  • K24A1 / K24A4 (CR-V / Accord) · PMC's adapter also lists the K24A1 to K24A4, the low-cost Accord and CR-V blocks; check that your chosen S2000 mount kit and intake route support the exact engine.

Mounts

The K24 itself mounts longitudinally with S2000 K-swap kits.

Engine mounts

Bolt-on K-swap mounts exist (RBZ in the ASM kit; Hasport in one documented build)

Sourced · medium45
Gearbox mountLikely custom fabricated for the DCT in an S2000Sourced · medium3
Engine stop

The K24 sits farther forward, so the factory engine stop cannot be used

Low confidence5

ASM's DIY kit is built around a USDM K24A2 and includes RBZ engine mounts, a K2F adapter plate, flywheel and header, while one documented build used Hasport mounts from ASM. That builder hand-tightened the mounts on the subframe, aligned the engine, then torqued them, and used thread locker on the bracket bolts because stiffer mounts add vibration.Medium45

The S2000 kits assume the Honda 6-speed. With the M DCT, the gearbox end needs its own mount: ASM, which has fitted the GS7D36SG to S2000s, says the mount most likely has to be custom fabricated, which it calls manageable for a skilled fabricator. Plan the mount after the engine and gearbox are set at the final height and angle.Medium3

Expect the engine to sit farther forward than the F20C. One builder found the factory engine stop unusable and the oil pan too low for an aftermarket subframe brace, fixed with half-inch spacers and longer bolts.Low5

Transmission

Adapter (PMC)
  • 20 mm aluminium adapter, bolts and a single-mass flywheel with DCT hub
  • K20 and K24 blocks listed
  • Starter and clutch not included
  • EUR 1,118 incl. VAT, sold out at capture
Sourced6
Adapter (SLG)
  • Billet adapter, hardened DCT spline adapter, balanced flywheel with sprung hub in several torque ratings, starter ring
  • From $1,900a related listing showed $1,575
Sourced · medium7
Park lock
  • Most swaps lock out park
  • Park delete parts are soldSLG lists one at $75
Sourced · medium3810
Fluid
  • MaxxECU lists Pentosin FFL-4
  • It says most DCT / DSG oils will likely work
Sourced · medium10

The GS7D36SG is the 7-speed wet dual-clutch BMW fitted to the E9x M3, F10 M5, F8x M2 / M3 / M4 and F-series M6, and it is swapped behind LS, K-series, rotary and JZ engines. The E9x M3 unit is gen 1; F-series units are gen 2, and controllers treat the two differently. ASM, for example, mainly uses the F80 DCT.

Decide which generation you are buying before ordering the adapter and controller.Medium11193

A K-to-DCT kit joins the Honda block to the BMW bellhousing and the crank to the dual-clutch input. PMC's kit is a 20 mm adapter plus a rigid single-mass flywheel with matched DCT hub; it excludes the starter and Honda bolts, and PMC notes a single-mass flywheel removes factory damping so gearbox noise is more audible. SLG's kit uses a sprung hub, offered in several torque ratings, to protect the clutch baskets.

Both listings name transmission versions, so match the kit to your exact gearbox.Medium67

The park mechanism is usually locked out rather than controlled. MaxxECU does not drive the park solenoid and requires an external park unlock, and SLG sells a park delete for owners who never need park while offering a park-lock option for those who do. Without park, the car relies on its handbrake when parked.Medium1083

Clearance

The M DCT is much larger than the Honda 6-speed.

Tunnel
  • Tight in some tunnels
  • On the S2000 part of the OEM gearbox mount bracing was cut out
Sourced · medium3
Engine bay

Crank pulley closer to the steering rack and valve cover closer to the firewall than the F20C

Low confidence5

ASM reports the gearbox can be tight in some tunnels and may need hammering or cutting, and on the S2000 it cut out part of the factory transmission mount bracing. Mock up with the real gearbox, check shift-linkage and harness clearance, and restore stiffness with a brace if you remove structure.Medium3

At the front, the K24 brings its own tight spots: one builder found the crank pulley closer to the power steering rack and the valve cover closer to the firewall than on the F20C, and tight clearance between the intake manifold, water pump housing and belt tensioner.Low5

Cooling

Engine coolant
  • Rear coolant housing and heater port adapter in the ASM kit
  • USDM water pump housing needed for intake fit in one build
Sourced · medium45
DCT oil thermostat (E9x M3)

Opens above about 95 C (203 F) and sends oil to a remote cooler in the front spoiler

Sourced · medium14
Track stress
  • Community reports the GS7 has thermal issues under track use
  • Swappers run a separate cooler
Low confidence133

On the engine side, the ASM kit supplies a rear coolant housing with hoses and a heater port adapter, and one builder had to swap the JDM water pump housing for a USDM one so the intake manifold would fit. Bleed the system from its highest point and confirm temperatures before track use.Medium45

The dual-clutch needs its own cooling, and that matters most on track. In the E9x M3 a thermostat sends DCT oil to a remote cooler once it passes about 95 C, and BimmerWorld lists a failed thermostat as a cause of hard shifts and limp mode. ASM runs a separate cooler, noting 8AN adapters are available, and HPA forum users report thermal issues under track stress.

Mount the cooler in clean airflow and log the gearbox oil temperature the TCU reports.Medium143139

Fuel

Reused S2000 parts (ASM route)

Fuel rail, injectors, regulator and throttle body from the F-series intake

Sourced · medium4

ASM's kit keeps the S2000's F-series intake manifold (modified, with an adapter to the K head), and with it the original throttle body, fuel rail, injectors, regulator and intake air sensor. Other routes use a K-series rear-drive manifold and the K24's own fuel parts, so the fuel system follows the intake you pick.Medium4

Size injectors and pump for your real power target and fuel, check fuel pressure under load, and confirm the S2000 pump and lines suit any boost plan. The SuperK car runs a turbo K24, which changes the fuel requirement completely.Low24

Exhaust

KPower sells a rear-drive K-swap header for the 2000-2009 S2000, and ASM includes it in its complete kit.

HeaderKPower S2000 K24 swap tri-header, included in the ASM kitSourced · medium415

From the header back, route the pipe around the larger M DCT and its custom mount, and keep heat away from the gearbox harness, the TCU connector and any cooler lines.Low1543

Electrical

ECU+ PDM / relaysCrank / cam sensorsThrottle (DBW) + pedalInjectorsCoilsEngine sensorsFuel pumpCooling fansGauges / tachStarter / chargingChassis loads

Today four routes are documented.

Gearbox bus
  • Run the DCT on its own CAN bus
  • Message load is high and IDs can collide
Sourced9
Required inputs (MaxxECU route)Brake pedal or stop-light signal and a wheel-speed sensor inputSourced10
Gen 1 supply (MaxxECU route)+12 V fused at 12 A, powered with the ECU, plus a +12 V wake-upSourced10
Shifter and paddles
  • OEM gen 1 selector optional with emulation
  • Any closing-contact paddle works with MaxxECU (OE BMW paddles not supported)
Sourced109
S2000 throttleCable throttle until drive-by-wire arrived on the 2006 AP2Sourced · medium16

MaxxECU builds GS7D36SG control into its engine ECU, using its own TCU firmware and DCT harness. CANTCU keeps the OEM TCU and works alongside MaxxECU, Emtron, MoTeC, Haltech, ECUMaster, Syvecs and others, at EUR 1,903 incl. VAT. HTG's GCU replaces the stock TCU (about $1,385, sold out at DriftHQ).

SLG removes the OEM controller and wires directly to the sensors and shift solenoids. The SuperK S2000 runs a gearbox control unit with its standalone engine management.Medium911122

The donor TCU's immobilizer is the first thing to settle. CANTCU's listing includes a built-in flasher for unlocking transmission immobilizers, and the MaxxECU route needs its own TCU firmware loaded to match your shifter and buttons. That step is done by the buyer with the controller maker's authorized tool.

On a K24 S2000 the gearbox has no BMW chassis around it, so the chosen controller has to supply what the TCU expects: engine speed and torque, pedal, brake, wheel speeds and more.Medium11919

With a replacement controller, the factory TCU in the gearbox is bypassed, so its sensors and solenoids are rewired to an external unit through a bulkhead connector, a job ASM puts at one to two days. Paddles can be microswitches, with a CAN keypad for mode selection. Fuse and relay the gearbox feed, give the DCT its own CAN pair, and keep it off any other bus.Medium39

GAINS ECU2 with PDM2 is planned to control the M DCT through its factory TCU over CAN, with ECU2 doing the torque cut and blip. This is planned, not supported today: it needs an ADR on CAN transmit, a buyer-supplied unlocked TCU, and logged bench and vehicle validation. GAINS never flashes or unlocks a TCU.19

Chassis

Every DCT swap needs a fabricated driveshaft.

Driveshaft

Likely custom, with an adapter from the BMW output flange to a 1350 flange

Sourced · medium31
Differential
  • Factory Torsen LSD, 4.100 final drive
  • AP1 and AP2 diffs use different prop shaft yokes and bolt sizes
Sourced · medium1617

For the S2000, ASM expects a custom shaft and an adapter from the BMW output flange to a 1350 flange, and suggests shops such as Full Torque Driveshafts. Measure with the engine and gearbox on their final mounts and the car at ride height.Medium13

The S2000 keeps its Torsen diff and 4.100 final drive. AP1 and AP2 diffs have different prop shaft yokes and bolt sizes, so the driveshaft's rear flange must match the diff you run. Fast dual-clutch shifts and wheel lift are hard on the driveline: replace prop shaft bolts when removed and check axles and diff mounts often.Medium1617

Tuning

The engine computer and gearbox controller must work as a pair.

ECU-to-gearbox signals
  • RPM, throttle, MAP, ignition, lambda, intake and coolant temperature, brake switch in
  • Power cut and downshift blip out
Sourced · medium3
Blip
  • The TCU requests a minimum blip RPM
  • If the engine misses it the TCU may disengage the clutches
Sourced9
Clutch relearnDone with INPA or a similar toolSourced · medium9

The ECU sends engine speed, throttle, load and temperatures and acts on requests for a torque cut on upshifts and a rev-match blip on downshifts. MaxxECU notes the blip must reach the TCU's requested RPM or the clutches may disengage, and prefers an electronic throttle for quick downshifts. Gearbox calibration covers engagement, shift and downshift behaviour, preselection, full-auto mode and safeties, and ASM says it can take days.Medium39

For the engine, Honda's K24A2 computer uses manifold pressure for load. A new intake, header and any turbo change airflow, so build fuel tables from wideband logs and set ignition only as far as knock monitoring and logs support. Do the clutch relearn with INPA or a similar tool after installation.Medium189

Parts checklist

Tick what you have; the list is saved in this browser.

0 of 25 ticked (saved in this browser)
Mounts
Transmission
Clearance
Cooling
Fuel
Exhaust
Electrical
Chassis
Tuning
Legal

Order of work

10 stages, in the order most builds follow.

  1. Pick the gearbox and controller
    Choose gen 1 (E9x M3) or gen 2, then the controller route. Confirm the donor TCU's immobilizer status and how the buyer will unlock or reflash it with the maker's tool.
  2. Pick the engine kit
    Choose a K24 and an S2000 K-swap kit route (mounts, intake, header, coolant housing) that the adapter maker lists for that block.
  3. Prepare the engine and gearbox
    Check compression and leak-down, fit the adapter, flywheel or hub and starter, and fit the park delete or unlock.
  4. Mock up
    Hang the engine on the K-swap mounts, offer up the DCT, and check the tunnel, bracing, steering rack, firewall and subframe clearances.
  5. Fabricate the gearbox mount
    Build the gearbox mount at the final height and angle, and reinforce any tunnel structure you cut.
  6. Driveshaft
    Measure at ride height and order a custom shaft with the BMW flange adapter and the correct rear flange for your diff.
  7. Cooling and fuel
    Plumb the engine coolant, fit the DCT oil cooler in clean airflow, and complete the fuel system.
  8. Wiring
    Wire the engine ECU, then the gearbox controller on its own CAN bus with a fused supply, brake and wheel-speed inputs, and paddles.
  9. First start and engagement
    Start on a base map, verify sensors and CAN traffic, do the clutch relearn, then calibrate engagement with the car safely supported or at low speed.
  10. Tune and shake down
    Tune fuel and ignition from logs, then cut and blip; log engine, gearbox oil temperature and shift data in short sessions before track use.

Common problems

Symptom, cause and the usual fix.

ProblemCauseFix
Gearbox will not shift or engage properlyThe TCU is missing CAN messages or inputs it expects (engine data, brake, paddles)Check every required input on the controller's list, and keep the DCT on its own CAN bus.Medium29
Clutches disengage on downshiftsThrottle blip does not reach the RPM the TCU requestedTune the blip so it reaches the requested RPM; electronic throttle is preferred.9
Shifts into neutral at high torqueM3 TCU may go to neutral above about 800 Nm; clutch pressure is limited to about 15.5 barLimit transmitted torque in the controller, or use upgraded hardware and firmware from the controller maker.9
Hard shifts or limp mode in hot sessionsDCT oil overheating or a failed oil thermostatFit a separate cooler, check the thermostat, and log gearbox oil temperature.Low14133
Gearbox will not fit the tunnelThe DCT is larger than the Honda 6-speedHammer or cut the tunnel and mount bracing as needed, then reinforce.Medium3
Driveshaft will not bolt to the diffAP1 and AP2 diffs use different yokes and bolt sizesSpecify the rear flange for the diff you run when ordering the shaft.Medium17

Frequently asked

Can you put a BMW DCT in an S2000?

Yes. The GS7D36SG has gone into K24 S2000 track cars, including the SuperK time-attack car. It needs a K-to-DCT adapter, a custom gearbox mount and driveshaft, some tunnel work, and a gearbox controller that talks to the engine ECU.Medium123

What controller runs a BMW DCT in a swap?

Published options are MaxxECU (built into its engine ECU), CANTCU (keeps the OEM TCU and works with several ECU brands), the HTG GCU (replaces the TCU) and SLG's direct-wire approach. Check current availability: the HTG unit showed as sold out at DriftHQ.Medium911122

Does the BMW DCT need an immobilizer unlock?

Often, yes. CANTCU ships a built-in flasher for unlocking transmission immobilizers, and MaxxECU needs its own TCU firmware. The buyer does this with the controller maker's authorized tool before the swap goes in.Medium119

Do you need a custom driveshaft?

Yes. Every DCT swap needs a fabricated shaft, and in the S2000 ASM uses an adapter from the BMW output flange to a 1350 flange. Match the rear flange to your AP1 or AP2 diff, which differ.Medium1317

Does the BMW DCT overheat on track?

It can. Community reports describe GS7 thermal issues under track stress, and a failed oil thermostat can cause hard shifts and limp mode. Swappers run a separate cooler and log the gearbox oil temperature.Low13143

How much does a K24 DCT S2000 swap cost?

There is no fixed figure. ASM's complete K-swap kit lists at $5,999 without the engine, adapters run from about EUR 1,118 to $1,900, CANTCU is EUR 1,903, and ASM doubts the DCT side can be done for much under $10k.Low467113

Can GAINS run the M DCT?

Not today. GAINS ECU2 with PDM2 is planned to control it through the factory TCU over CAN, with ECU2 doing cut and blip, after validation. GAINS will never flash a TCU or remove its immobilizer.19

Related

Sources

24 sources
  1. Here's Why Geniuses Are Swapping BMW Transmissions Into Everything From Muscle Cars To S2000s · The Autopian · press · retrieved 2026-11-03
  2. Dual-Clutch Transmission Swaps Are a Thing and I'm Here for It · The Drive · press · retrieved 2026-11-03
  3. The BMW DCT Swap FAQ (blog, January 2021) · ASMotorsports · vendor-doc · retrieved 2026-11-03
  4. S2000 DIY K-swap Complete Kit (product listing) · ASMotorsports · vendor-doc · retrieved 2026-11-03
  5. K24 S2000 (Pt 3) · FunctionTheory · community · retrieved 2026-11-03
  6. Adapter Kit Honda K K20 K24 - BMW DCT DKG Getrag GS7D36SG N54 N55 S55 (V) · PMC Motorsport · vendor-doc · retrieved 2026-11-03
  7. Honda K-Series to DCT Adapter Kit · Seems Legit Garage · vendor-doc · retrieved 2026-11-03
  8. BMW DCT Park Delete · Seems Legit Garage · vendor-doc · retrieved 2026-11-03
  9. CAN peripherals: BMW E92 DCT (GS7D36SG) · MaxxECU · vendor-doc · retrieved 2026-11-03
  10. DCT installation and wiring · MaxxECU · vendor-doc · retrieved 2026-11-03
  11. CANTCU Transmission Controller (product listing) · SPS Motorsport (Canformance CANTCU) · vendor-doc · retrieved 2026-11-03
  12. HTG Gearbox Control Unit (product listing) · DriftHQ · vendor-doc · retrieved 2026-11-03
  13. Is HTG the best option? (forum thread) · High Performance Academy forum · community · retrieved 2026-11-03
  14. BMW DCT Transmission Oil Thermostat - E9X M3 DCT 17212283325 · BimmerWorld · vendor-doc · retrieved 2026-11-03
  15. KPower RWD K Swap Header for 2000-2009 Honda S2000 · KPower Industries · vendor-doc · retrieved 2026-11-03
  16. Honda S2000 · Wikipedia · reference · retrieved 2026-11-03
  17. S2000 Differential Swap · Rob Robinette · community · retrieved 2026-11-03
  18. 2004 Acura TSX Powertrain (press release, part 2) · American Honda Motor Co. (Acura) · oem · retrieved 2026-10-25
  19. internal GAINS internal: PDM2: dual-clutch transmission support and connector pin ganging v1 (AI research draft, unreviewed)
  20. Tampering Policy: The EPA Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices under the Clean Air Act (Nov 2020) · US Environmental Protection Agency · standard · retrieved 2026-10-25
  21. Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-25
  22. Change vehicle details on a V5C: what evidence to give · GOV.UK (DVLA) · standard · retrieved 2026-10-25
  23. Strassenverkehrs-Zulassungs-Ordnung (StVZO) section 19: Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
  24. Vehicle Standards Bulletin 14 (VSB 14): National Code of Practice for Light Vehicle Construction and Modification · Australian Government, Department of Infrastructure · standard · retrieved 2026-10-25