Factory specification
Layout, dimensions and factory hardware, each with its source.
Facts tagged “Researched, unverified” come from our engine catalog without a cited source yet.
K24Z7 horsepower and torque
Ratings as the manufacturer published them, with their basis. They are not GAINS measurements or tuning results.
K24Z7 firing order
K24Z7 injectors
The factory injector, then direct-fit upgrades the makers list for this engine.
Factory injector
Direct-fit upgrades
Sets the maker lists for this engine. Fit is the maker’s own statement; flow is the maker’s rating and test basis.
| Injector | Flow | Fit |
|---|---|---|
| DeatschWerks DW 650cc matched set · 17U-08-0650-4Medium16 | 650 cc/min maker rating (basis not stated on page) | Needs adapter USCAR-to-OEM plug adapter (DW page states USCAR connector; adapter inclusion not stated) |
| Fuel Injector Clinic FIC 525cc High-Z set · is114-0525h15 | 525 cc/min at 43.5 psi (3 bar), CF-16B fluid 90 F (maker) | Needs adapter solder-in pigtails PGTUSC4 (included); no PnP adapter listed on this product |
| Fuel Injector Clinic FIC 1000cc High-Z set · is114-1000h17 | 1000 cc/min at 43.5 psi (3 bar), CF-16B fluid 90 F (maker) | Needs adapter solder-in pigtails PGTUSC4 (included); no PnP adapter listed on this product |
| Injector Dynamics ID1050-XDS · 1050.07.21.48.14.4461012 | 1065 cc/min at 3.0 bar, gasoline 52 C (maker) | Needs adapter USCAR-to-Honda plug adapters (ID connector is USCAR; adapters sold separately per retailer listings E-1238) |
| Injector Dynamics ID1300-XDS · 1300.07.21.48.14.4571113 | 1335 cc/min at 3.0 bar, iso-octane 52 C (maker) | Needs adapter USCAR-to-Honda plug adapters (ID connector is USCAR; adapters sold separately per retailer listings E-1238) |
K24Z7 swap
Swap guides that recommend this engine or its family. Each guide covers mounts, transmission, fuel, wiring, tuning and the law, with sources.
Sensors
Factory sensors by role: part numbers, signal type and fitment years.
| Sensor | OEM part numbers | Type / signal | Years and markets |
|---|---|---|---|
| Knock | Honda 30530-R1A-A01 (replaces 30530-5YS-J01)Sourced14 | knock sensor | US 2012 Civic all trims incl. Si (K24Z7) |
| MAP | Honda 37830-RNA-A01Sourced14 | MAP sensor | US 2012 Civic all trims incl. Si |
| MAF | Not yet sourcedSourced · medium14 | none listed in OEM catalogue (speed-density, MAP-based) | |
| O2 (upstream) | Honda 36531-RX0-A01Sourced14 | wideband air-fuel ratio sensor | US 2012 Civic Si (KA 6MT) |
| O2 (downstream) | Honda 36532-RX0-A01Sourced14 | oxygen sensor (lower) | US 2012 Civic Si |
Ignition and triggers
Tuning notes
Factory load sensing
The factory ECU measures load by a strategy that changes with year and market. 2012 Civic Si (K24Z7) press: DBW; PGM-FI monitors air flow and air/fuel ratio (suggests MAF fitted; MAP use not stated). Earlier K24Z (2007-11 CR-V/Accord) not checked - may be MAP-only like K24A.Medium1
Factory oxygen sensors
Upstream: wideband A/F upstream (2012 Si press lists air/fuel ratio) (1). Downstream O2 sensors: yes. Closed-loop fuelling: A/F-sensor closed loop at part load; open loop enrichment at high load.Medium1
Injector drive
Factory injector impedance: high (saturated). Connector: Honda (K24Z7; FIC lists pigtails only).Low689
Driver and calibration
High-impedance injectors run from a saturated driver. Any injector change needs new flow and dead-time data in the calibration. Researched, unverified
Known limits (reported)
Stock rods and especially rod bolts are commonly reported as the first bottom-end limit under boost (vendor and forum consensus); some builders also add sleeves or a block guard because the block is open-deck (single forum opinion).Low23
Common first upgrades (reported)
Builders most often report upgrading: forged rods with upgraded bolts (vendor/forum).Low23
Valvetrain, factory engine management and weak points across every generation are on the Honda K-series guide.
Vehicles with the K24Z (K24Z7 Civic Si)
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
17 sources
- Honda K20Z3 / K24Z7 sensing (E-827) · hondanews.com · oem · retrieved 2026-10-25
- Honda K-series internals (E-1035) · en.wikipedia.org · reference · retrieved 2026-10-25
- Honda K-series limits (E-1036) · hybrid-racing.com · vendor-doc · retrieved 2026-10-25
- Injector aftermarket fitment (E-1200) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injector aftermarket fitment (E-1201) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injectors / ID1050-XDS fitment (E-1230) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injectors / ID1300-XDS fitment (E-1231) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injectors / FIC Honda sets (E-1234) · fuelinjectorclinic.com · vendor-doc · retrieved 2026-10-25
- Injectors / DW Honda sets (E-1236) · deatschwerks.com · vendor-doc · retrieved 2026-10-25
- Injector Dynamics ID1050-XDS fitment table (E-1260) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injector Dynamics ID1300/ID1750/ID2600 fitment tables (E-1261) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injector Dynamics ID1050-XDS fitment table (E-1290) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injector Dynamics ID1300-XDS fitment table (E-1291) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- OEM sensor PNs (Honda Civic 2008/2012) (E-1354) · hondapartsnow.com · vendor-doc · retrieved 2026-10-25
- fuelinjectorclinic.com product listing · fuelinjectorclinic.com · vendor-doc · retrieved 2026-10-25
- deatschwerks.com product listing · deatschwerks.com · vendor-doc · retrieved 2026-10-25
- fuelinjectorclinic.com product listing · fuelinjectorclinic.com · vendor-doc · retrieved 2026-10-25
Evidence ids (E-…) refer to our research register; each records the source, date and confidence.


