Engine: K24Z (K24Z7 Civic Si)
Part of the Honda K-series family.
Modeled power and torque
Modelled estimate, not a dyno result.
Dyno model not available yet for the K24Z (K24Z7 Civic Si). Stock-anchored curves are added as factory ratings are sourced.
K24Z (K24Z7 Civic Si) data
- Load sensing
- mixed by year/market
- O2 sensor
- wideband A/F upstream (2012 Si press lists air/fuel ratio)
- Closed loop
- A/F-sensor closed loop at part load; open loop enrichment at high load
- Block
- aluminium
- Rods / pistons
- Not yet sourced
- Reported limit
- Very wide spread: rod vendor (Hybrid Racing) says ~250-300 whp on stock rods; forum reports of ~550-600 whp on stock K24 bottom ends (forum anecdote, low confidence)
- Factory
- Honda top-feed (Keihin/Denso family; maker not confirmed)
- Impedance
- high (saturated)
- Direct-fit upgrades
- 5 maker-listed
- Knock
- Honda 30530-R1A-A01 (replaces 30530-5YS-J01)
- MAP / MAF
- Honda 37830-RNA-A01
- O2 (upstream)
- Honda 36531-RX0-A01
Platform background
For 2012 Honda moved the Civic Si to the 2.4-litre K24Z7. It makes 201 hp and 170 lb-ft (205 hp from 2014), adding 31 lb-ft of torque over the K20Z3 it replaced. It keeps drive-by-wire, coil-on-plug direct ignition, a block-mounted knock sensor and a helical LSD, paired with a 6-speed manual only.
Factory ECU
Factory ECU: harness cross-reference
From the factory ECU each listed harness plugs into. The factory ECU is unplugged, not modified. Check the label and part number on your own ECU before ordering.
- ECU family
- Honda R/K-series
- Applies to
- 2012-15 Civic manual
Ambiguous R18 vs Si K24Z7.
Factory ECU pinout: pending
No OEM pin table is in our library yet for the K24Z (K24Z7 Civic Si) factory ECU. No OEM-grade ECM/PCM terminal table could be read for this guide (the factory manuals located online are image-only). Competitor plug-in manuals were not used, by policy. Needed: Honda 2012-2015 Civic Service Manual and Electrical Troubleshooting Manual, PCM connector terminal tables for the 2.4 L K24Z7. Until then, wire from the harness maker's instructions or the factory service manual.
Factory ECU pinout
No OEM-grade ECM/PCM terminal table could be read for this guide (the factory manuals located online are image-only). Competitor plug-in manuals were not used, by policy. Needed: Honda 2012-2015 Civic Service Manual and Electrical Troubleshooting Manual, PCM connector terminal tables for the 2.4 L K24Z7.
Plug-and-play harness
No Haltech S3 plug-in harness is listed for this vehicle, but a Boomslang adapter harness is: it plugs into the factory ECU connector on one side and the S3 pinout on the other, so the ECU2 replaces the factory ECU without cutting the loom. Nothing is written to the factory ECU. Pin-compatible per the published S3 pinout, not yet fit-tested.
| Maker | Harness | Fits | Link | |
|---|---|---|---|---|
![]() | Manual 2012 - 2015 Honda CivicBF29141-S3 | 2012-15 Civic manual | $1,200 | Maker ↗ |
| Wire-in | Universal flying lead or re-terminated factory harness | Any engine (terminate to ECU2's two Superseal 34 connectors) | Universal harness from $405 | Maker ↗ |

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 2012 - 2015 Honda Civic
- Plugs into
Honda ECM (9th-gen Civic)
- ECU
- Honda R/K-series
- Confidence
- low
Ambiguous R18 vs Si K24Z7.
- Fits
- 2012-15 Civic manual
- SKU
- BF29141-S3
- Maker fitment
- Honda Civic (Manual); selector years 2012-2015; SKU label: Manual 2012 - 2015 Honda Civic
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2)
Haltech and Boomslang are trademarks of their respective owners. GAINS is not affiliated with or endorsed by them.
Your GAINS system for this car · pre-release
ECU2 for the Civic Si 9th gen
Planned with the same rules as the configurator for this car's 4 cyl · port injection · drive-by-wire. The factory ECU is unplugged and replaced; nothing is written to it.

- Price TBA
ECU2Engine controller
4 cyl · port injection · drive-by-wire
Full sequential fuel and spark for this 4-cylinder, and its electronic throttle, with the wideband built in.
in designEst. availability: April 2027
Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →
Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →
What you get
- A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
- Faults in plain words"Coolant temp sensor open circuit.
- Drive-by-wire built inFour half-bridges run up to two electronic throttles, with pedal and throttle sensors on the ECU's own inputs and a windowed watchdog that cuts the motors in hardware on a fault.
- S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
- Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
- GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.
How it wires in
- Haltech S3 plug-in harnessNone listed for this car
- Factory-connector → S3 adapter1 listed · from $1,200 USD listBF29141-S3
- Wire-inAlways possible
Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓
ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.
Swap guides
The K24Z (K24Z7 Civic Si) family in other cars
How GAINS approaches the Civic Si 9th gen
Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.
- 1Base map and first startplanned
Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.
- 2Lambda targets and VE learningclosed loop on GAINS ECUs
Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.
- 3VTEC crossoverplanned
VTEC engagement is treated as a load and rpm surface where the two cam profiles cross on torque, learned from logs rather than a single fixed rpm.
- 4Cam phasing (VVT)gated
Begin with conservative overlap. Cam targets per load cell are then chosen with torque and knock in mind, keeping idle and cold overlap low for stability. Widening cam authority follows the same evidence-gated path as spark.
- 5Drivability foundationsplanned
Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.
- 6Factory load sensingfactory reference
What the factory ECU measures load with: varies by year/market (medium confidence); 2012 Civic Si (K24Z7) press: DBW; PGM-FI monitors air flow and air/fuel ratio (suggests MAF fitted; MAP use not stated). Earlier K24Z (2007-11 CR-V/Accord) not checked - may be MAP-only like K24A.
- 7Wideband sensorhardware
the factory sensor is already an A/F type; for tuning, fit a Bosch LSU 4.9 for the GAINS ECU's built-in controller (factory A/F sensors are not LSU-compatible)
- 8Bottom end and head sealingfactory reference
Reported: Stock rods and especially rod bolts are commonly reported as the first bottom-end limit under boost (vendor and forum consensus); some builders also add sleeves or a block guard because the block is open-deck (single forum opinion). (low confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.
Drivetrain
Chassis integration
Tuning notes
The long stroke moves peak torque low (4400 rpm), so knock margin in the mid-range is the main ignition constraint on pump fuel at 11.0:1. Log knock retard from the factory sensor through every change.
Popular swaps
GAINS on the Civic Si 9th gen
ECU2
Designed so your phone is the laptop, keypad and dash
The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.
Wideband, IMU and logging built in
An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.
Modular, so you buy what the engine needs
This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.
Calibration that keeps learning
Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.
Adaptive tuning strategies
- VE learning closed loop on GAINS ECUs
Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.
- Goal-based lambda targets closed loop on GAINS ECUs
Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.
- Knock protection protection
Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.
- Warm-up, cranking, idle and transient fuel planned
The same learning approach applied to the tables tuners spend hours on after the main map is done.
- Spark advance and boost authority gated
Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.
Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.
GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.
Frequently asked
What engine is in the 2012-2015 Civic Si?
The K24Z7 2.4-litre i-VTEC, with 201 hp in 2012-13 and 205 hp in 2014-15.34
When does VTEC engage on the 9th gen Si?
Honda describes the intake switching to high-lift profiles above 5000 rpm.3
Does the 9th gen Civic Si have an LSD?
Yes, a helical limited-slip differential.3
Was there an automatic 9th gen Civic Si?
No. Honda lists the 6-speed manual as the only transmission.3
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
- EFK K-Series Mount Kit (88-91 Civic/CRX) · Hasport Performance · vendor-doc · retrieved 2026-10-25
- EGK K-Series Mount Kit (92-95 Civic, 94-01 Integra, Del Sol) · Hasport Performance · vendor-doc · retrieved 2026-10-25
- 2012 Honda Civic Powertrains (Civic Si 2.4-liter i-VTEC) · American Honda Motor Co. (hondanews.com) · press · retrieved 2026-10-25
- Honda Civic Si Timeline and Milestones · American Honda Motor Co. (hondanews.com) · press · retrieved 2026-10-25
Catalog data and evidence
- Catalog data, not yet expert-reviewed.
- No vehicle photos: illustrations only until licensed imagery is available.
- E-934 Boomslang identity (sourced, high confidence)
- E-935 Boomslang S3 catalog size (sourced, high confidence)
- E-900 Haltech Nexus S3 catalog (sourced, high confidence)
- E-941 S3 engine harness availability (inferred, medium confidence)



