No lift shift (flat shift)

NLSno-lift shiftflat shiftflat shiftingfull-throttle shiftpowershift

No lift shift is a manual-transmission feature that lets the driver change gear without lifting off the accelerator. When the clutch is pressed above a set engine speed, the engine controller briefly cuts or reduces torque so the engine does not flare, then restores power as the clutch re-engages. Flat shift is another name for it.12

How it works

In a normal upshift the driver lifts off, and the engine and turbo lose speed.

With flat shift the driver stays at full throttle; the engine controller manages torque instead. Wikipedia describes the technique as reducing the time the driven wheels are unpowered.Medium2

Where the name comes from

GM introduced No-Lift Shift as a factory feature on the turbocharged 2008 Chevrolet Cobalt SS, alongside launch control. The driver presses the clutch as usual while the accelerator stays floored, and the car keeps turbo boost through the upshift. Later GM manual cars, including 2016 to 2024 Camaros, use the same name.41

GM's description for 2016 to 2024 manual Camaros is the most detailed available. The throttle stays fully open, and on triggering the controller applies immediate torque control with fuel and spark for a short period, then a predictive throttle-based control takes over to avoid heating the catalyst.1

GM lists an enable engine speed and a target speed for each engine. In its example, a 2017 Camaro SS above 5,000 rpm can be upshifted at full throttle and the tachometer settles at 6,400 rpm during the shift. A minimum road speed of 15 km/h (9.3 mph) applies.1

GM states that its 2.0-liter turbo Camaro holds boost through a no-lift shift instead of losing it as in a normal shift. That boost retention is a main reason the feature is popular on turbocharged cars.1

Typical values

Trigger

Clutch switch or clutch position sensor, above an enable engine speed

Sourced12
Torque reduction (GM)Fuel and spark briefly, then throttle-based controlSourced1
Example enable and target (2017 Camaro SS)
  • Above 5,000 rpm
  • Engine held near 6,400 rpm during the shift
  • Minimum 15 km/h9.3 mph
Sourced1
Ends whenThe clutch re-engages in the next gearSourced · medium1

In tuning

Flat shift needs a reliable clutch signal, either a switch or a position sensor, plus an engine speed enable and a target speed or cut duration. The cut must end as soon as the clutch re-engages, or the car hesitates.Medium12

Torque reduction method matters. GM's approach uses fuel and spark briefly, then throttle, to protect the catalyst. Long ignition-cut periods with full fuel send unburned mixture into the exhaust and cause heat and backfires.13

Shifting at full engine torque loads the synchronizers, clutch and driveline harder than a lifted shift. Gearboxes not designed for it can wear faster.Low2

Try it

rpm
:1
:1
in

Result

Road speed145.2 mph

Planning estimate from the formula below, not a measurement.

Open the full gear ratio speed calculator →

Common mistakes

Mistake Using a long ignition-only cut with full fuel.

Do instead Keep the cut short and reduce fuel too, or hand over to throttle control as GM does, so unburned mixture does not reach a hot exhaust and catalyst.Medium13

Mistake Ending the cut on a timer instead of on clutch re-engagement.

Do instead Release the torque cut as the clutch comes back up, otherwise the car hesitates in the new gear.Medium1

Myths vs facts

Myth Flat shifting just uses the normal rev limiter.

Fact OEM systems use a dedicated torque control with enable and target speeds. GM describes fuel, spark and throttle working in sequence.1

Myth Flat shifting is always ignition cut.

Fact Methods vary. GM documents fuel and spark control followed by throttle control, not ignition cut alone.1

Frequently asked

What is no lift shift?

No lift shift lets you upshift a manual car with the accelerator still floored. The engine controller sees the clutch go down, holds the engine at a target speed by briefly reducing torque, and restores power when the clutch comes back up. GM first offered it on the 2008 Cobalt SS Turbocharged.41

How does no-lift shift work?

The driver keeps the accelerator floored and presses the clutch above a set engine speed. The controller detects the clutch and briefly reduces torque so the engine holds a target speed instead of flaring. When the clutch re-engages in the next gear, full torque returns. GM describes fuel and spark control followed by throttle control.1

Is flat shifting bad for your car?

On cars designed for it, such as GM's manual Camaros, it is a supported feature. It still loads the clutch, synchronizers and driveline harder than a lifted shift, so wear can rise with frequent use. On cars without factory support, crude ignition-cut setups can add exhaust heat and backfires.Medium12

Does flat shifting keep boost?

It can. Because the throttle stays open and the controller manages torque instead, exhaust flow and turbo speed drop less during the shift. GM states its 2.0-liter turbo Camaro does not lose boost during a no-lift shift as it would in a normal shift.1

What is the difference between flat shift and power shift?

The terms overlap. Power shifting generally means shifting a manual without lifting, managing the clutch quickly at full throttle. Flat shift or no-lift shift usually refers to the engine controller feature that cuts torque during the clutch press so the engine does not over-rev. Wikipedia treats flat shifting as a form of powershifting.Medium21

Used in these guides

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. GM Preliminary Information PIC6454A: No Lift Shift feature (Camaro 2016-2024) · General Motors (hosted by NHTSA) · service-manual · retrieved 2026-10-25
  2. Powershifting (flat shift) · Wikipedia · reference · retrieved 2026-10-25
  3. Rev limiter · Wikipedia · reference · retrieved 2026-10-25
  4. Chevrolet Cobalt SS (2008 SS Turbocharged: no-lift-shift and launch control) · Wikipedia · reference · retrieved 2026-10-27