CAN bus termination

CAN terminating resistor120 ohm terminationCAN termination resistorsplit termination

CAN bus termination is the pair of resistors, normally 120 Ω each, fitted across CAN high and CAN low at the two physical ends of a high-speed CAN bus. They match the cable's characteristic impedance so signals do not reflect from the line ends, and they set the bus's differential load.123

How it works

High-speed CAN uses a twisted pair with about 120 Ω characteristic impedance.

TI's physical-layer note describes a bus terminated at both ends with 120 Ω resistors that match that impedance. Without them, each edge reflects from the open ends and can corrupt bits at higher bit rates.13

Termination belongs at the ends of the main bus, not in every node. TI advises against placing termination inside a node, because the bus loses termination if that node is unplugged. Nodes connect through short stubs; the ISO 11898 figures TI quotes are 1 Mbps over 40 m with up to 30 nodes and unterminated stubs no longer than 0.3 m.14

Split termination replaces each 120 Ω resistor with two 60 Ω resistors in series, with a capacitor from their midpoint to ground. It filters common-mode noise and is a common option for improving electromagnetic emissions.1

In tuning

When adding an engine controller, dash, logger or keypad to an existing bus, find out where the bus ends are and which devices already contain termination. Adding a third resistor lowers the load below spec, while removing one leaves the bus underterminated.Medium12

A quick check is resistance between CAN high and CAN low with all devices powered off. Two correct terminations in parallel read about 60 Ω; about 120 Ω means one is missing and about 40 Ω suggests three.1

Formula and worked example

R_bus = 1 / (1/R1 + 1/R2 + ... + 1/Rn)
R_bus
resistance measured between CAN high and CAN low, powered offΩ
R1...Rn
each termination resistor on the busΩ
1

Myths vs facts

Myth Every CAN device should have a 120 Ω resistor.

Fact Only the two devices or harness points at the physical ends of the bus should terminate it. Extra terminators load the transceivers and reduce signal margin.12

Myth Termination does not matter on a short bus.

Fact Short buses are more forgiving, but the bus still needs its defined load for the transceivers to work as specified, and missing termination can cause intermittent errors that are hard to trace.Medium1

Frequently asked

Why does a CAN bus need termination?

The resistors match the twisted pair's roughly 120 Ω characteristic impedance, so each signal edge is absorbed at the end of the line instead of reflecting back. They also provide the defined differential load the transceivers expect. Without termination, reflections and slow recessive edges cause bit errors, especially at higher bit rates.13

Why do I measure 60 Ω on my CAN bus?

That is the correct reading. With power off, the two 120 Ω terminators at the bus ends appear in parallel between CAN high and CAN low, giving 60 Ω. About 120 Ω means one terminator is missing; about 40 Ω means a third one has been added.1

Where do you put CAN bus termination resistors?

At the two physical ends of the main bus, between CAN high and CAN low. Nodes in between connect through short stubs without termination. TI recommends not relying on termination inside a removable node, because unplugging it would leave the bus unterminated.14

How long can a CAN bus stub be?

Keep stubs as short as possible. The high-speed CAN figures TI cites recommend a maximum unterminated stub length of 0.3 m (about 12 in) at 1 Mbps. Lower bit rates tolerate longer stubs, but long stubs act like small unterminated lines and add reflections.14

Used in these guides

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Controller Area Network physical layer requirements (SLLA270) · Texas Instruments · vendor-doc · retrieved 2026-10-27
  2. CAN bus · Wikipedia · reference · retrieved 2026-10-27
  3. Reflections of signals on conducting lines · Wikipedia · reference · retrieved 2026-10-27
  4. Critical spacing of CAN bus connections (SLLA279) · Texas Instruments · vendor-doc · retrieved 2026-10-27