Ford · Variable reluctance (VR, AC)

Ford BR3Z-6C315-B crank sensor (Coyote Gen 1/2)

Ford BR3Z-6C315-BMotorcraft DY1293

Ford BR3Z-6C315-B (Motorcraft DY1293, replacing -A) is the crank sensor listed for 2011-17 Mustang GT Coyote Gen 1 and Gen 2 engines. A forum report says the 2018-on part (JR3Z-6C315-A) has a 3-pin connector where the earlier sensor has 2 pins, so Gen 3 sensors do not plug in. Ford does not publish the sensor technology publicly.Medium123

Key specifications

Measures: Crank trigger wheel teeth. Output: Variable reluctance (VR, AC).

Connector pins2(2011-17) vs 32018-on JR3Z-6C315-ALow confidence3
Fitment2011-17Mustang GT 5.0Sourced · medium2
Sensor technologyVRinferred from 2-pin connectorNot stated by Ford in a public document we archived.Researched, unverified
Part numberMakerNote
BR3Z-6C315-BFordReplaces BR3Z-6C315-AMedium12
DY1293MotorcraftMedium2

Pinout and connector

No pinout is shown: the maker or OEM does not publish one in a document we could cite. Identify pins with a meter before wiring.

Connector not published. Browse the connector library

How it's calibrated

ECU-neutral: enter these values in whichever ECU you use. Nominal values without the maker's tolerance band.

Trigger setup

  • Trigger type: Variable reluctance (AC, two-wire signal).123
  • Trigger edge: not published by the maker. Confirm the edge your ECU uses with a scope or a timing light before running the engine.

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptConfigurable (generic input)CRANK (pin 13) or CAM (pin 15): VR or Hall, single-ended, adaptive threshold; shielded cable with the shield at sensor ground. Concept hardware.Medium4
Haltech (Elite / Nexus)Configurable (generic input)Trigger or Home input; Haltech's wiring diagram lists reluctor (VR) support.9
Link (G4X)UnverifiedLink's G4X page does not state VR support; its VR sensor page names no ECU model.No public source
MoTeC (M1)UnverifiedThe M150 page lists programmable digital trigger inputs but does not name VR sensors.No public source
ECUMaster (EMU Black)Configurable (generic input)Trigger input (3: primary and 2 cams), Hall or VR selected in software.10
AEM (Infinity)Configurable (generic input)Differential VR input.11
MaxxECUConfigurable (generic input)Trigger input (VR or digital) on the RACE.12
Holley (Terminator X / EFI)Configurable (generic input)Crank or cam input. Holley recommends Hall sensors and asks for shielded cable with magnetic (VR) pickups.Medium13

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

  • Parts catalogueOfficial parts-catalogue listing (no data sheet or CAD published)Medium8Download from Ford PartsNo login at last check; the maker may change this

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Engines that use it

From the platform catalog's sensor table; check fitment against your engine code and model year.

Wiring and installation

If two-wire VR, run a shielded twisted pair to the crank input with the drain at the ECU end only, and check polarity with a scope.Medium76

Failure modes and checks

Gen 3 sensor will not plug in

Likely cause 2-pin vs 3-pin connector change

Check Use the sensor for your engine year.Low3

Timing shifts with rpm

Likely cause Reversed polarity (if VR)

Check Swap the two signal wires and re-check on a scope.Medium6

Frequently asked

Is the 2018 Coyote crank sensor the same as 2011-17?

No. Ford lists JR3Z-6C315-A for 2018-on, and a forum report says it has a 3-pin connector against 2 pins on the 2011-17 BR3Z-6C315-B.Low13

What is the Motorcraft number for the 2011-17 Coyote crank sensor?

DY1293, sold as BR3Z-6C315-B.Medium2

Related

Use it with GAINS

Ford BR3Z-6C315-B crank sensor (Coyote Gen 1/2) on GAINS hardware

ECU2CRANK (VR or Hall, single-ended, adaptive threshold)

Pins
On the ECU2 pin map
Pull-up
To be confirmed
Shielding
Shielded, drain at the ECU end only

Shielded cable, shield to sensor ground at the ECU end only. Hall pull-up arrangement to be confirmed in the schematic.Medium4

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.45

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

13 sources
  1. OEM sensors Ford Mustang: Ford part numbers for Mustang knock/crank/cam/MAF/MAP/O2 1990-2025 (5.0 pushrod, 4.6 2V/3V/4V, 5.4 GT500, Coyo · fordpartsgiant.com · oem · retrieved 2026-10-25
  2. Ford Coyote crank sensor retail: Genuine Ford crank sensor DY1293 / BR3Z-6C315-B for 2011-17 Mustang 5.0; DU99 / 9L8Z-6B288-B cam · americanmuscle.com · vendor-doc · retrieved 2026-10-25
  3. Ford Coyote crank connector change: Forum report: 2018-23 crank sensor JR3Z-6C315-A is 3-pin vs 2-pin on 2011-17; Parkway Ford lists Motorcraft DY · mustang6g.com · community · retrieved 2026-10-25
  4. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  5. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  6. LM1815 adaptive variable reluctance sensor amplifier data sheet · Texas Instruments · vendor-doc · retrieved 2026-10-27
  7. Shielded cable · Wikipedia · reference · retrieved 2026-10-27
  8. Ford Parts catalogue listing · Ford Parts · oem · retrieved 2026-10-27
  9. Nexus R3 wiring diagram (HT-193000_WD) · Haltech · vendor-doc · retrieved 2026-10-27
  10. EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-10-27
  11. Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
  12. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-10-27
  13. HP / Dominator EFI wiring manual 199R10555 · Holley · vendor-doc · retrieved 2026-10-27

Not yet indexed: fewer than 3 FAQs.