BMW · Hall effect (digital)

BMW 12141709616 Hall crank sensor (M54)

BMW 12141709616

BMW 12141709616 is the crank position sensor for the M54 straight-six. BMW's MS42/MS43 training material describes the system's crank sensor as a Hall-effect type, so it needs a supply and outputs a digital square wave rather than the AC signal of a VR sensor. It has three wires.23

Key specifications

Measures: Crank trigger wheel teeth (digital square wave). Output: Hall effect (digital).

TechnologyHall effect, 3-wireSourced2
OutputDigital square waveSourced2
PinoutUnverifiedNot published here until a BMW wiring document is archived.Researched, unverified
Part numberMakerNote
12141709616BMW23

Pinout and connector

No pinout is shown: the maker or OEM does not publish one in a document we could cite. Identify pins with a meter before wiring.

Connector not published. Browse the connector library

How it's calibrated

ECU-neutral: enter these values in whichever ECU you use. Nominal values without the maker's tolerance band.

Trigger setup

  • Trigger type: Hall effect (digital square wave).2
  • Output: Digital square wave.2
  • Trigger edge: not published by the maker. Confirm the edge your ECU uses with a scope or a timing light before running the engine.

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptTo be confirmedCRANK (pin 13) or CAM (pin 15) accept Hall in the concept, but the pull-up on these inputs is still an open item.Medium4
Haltech (Elite / Nexus)Configurable (generic input)Trigger or Home input in digital mode with the 5 V pull-up selected.Medium6
Link (G4X)Configurable (generic input)Trigger input; Link sells a Hall sensor kit listed for all Link ECUs.Medium7
MoTeC (M1)UnverifiedThe M150 page lists programmable digital inputs but does not name Hall trigger sensors.No public source
ECUMaster (EMU Black)Configurable (generic input)Trigger input (3: primary and 2 cams), Hall or VR selected in software.8
AEM (Infinity)Configurable (generic input)Crank or cam Hall input (10 kΩ pull-up to 12 V per AEM).9
MaxxECUConfigurable (generic input)Trigger input in digital mode, or an extra digital input for speed sensors.10
Holley (Terminator X / EFI)Configurable (generic input)Crank or cam input; Holley recommends Hall sensors.11

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

The maker does not publish a data sheet, drawing or CAD model for this part that we could find.

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Engines that use it

From the platform catalog's sensor table; check fitment against your engine code and model year.

Wiring and installation

Supply, ground and signal to a Hall-capable crank input with a pull-up if the output is open collector.Medium21

Failure modes and checks

No rpm with good wiring

Likely cause Input configured for VR instead of Hall

Check Set the input to Hall and confirm the pull-up.Medium1

Intermittent stall when hot

Likely cause Failing sensor

Check Log rpm while heat-soaked; a dropout points to the sensor.Low1

Test it with a multimeter

  • With the supply connected and a pull-up on the signal, the signal pin should switch between near 0 V and the pull-up voltage as a tooth passes (turn the engine slowly). Maker output: Digital square wave.2

Frequently asked

Is the BMW M54 crank sensor Hall or VR?

Hall effect, per BMW's MS42/MS43 training material: three wires with a digital square-wave output.2

Which engines in the catalog use 12141709616?

The catalog lists it for the M54.23

Related

Use it with GAINS

BMW 12141709616 Hall crank sensor (M54) on GAINS hardware

ECU2CRANK (VR or Hall, single-ended, adaptive threshold)

Pins
On the ECU2 pin map
Pull-up
To be confirmed
Shielding
Shielded, drain at the ECU end only

Shielded cable, shield to sensor ground at the ECU end only. Hall pull-up arrangement to be confirmed in the schematic.Medium4

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.45

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

11 sources
  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. sensors: BMW M52TU/M54 (MS42/43): 2 knock, Hall crank, HFM, Bosch LSH 25, EDK/PWG · archive.org · oem · retrieved 2026-10-25
  3. part numbers: FCP Euro BMW knock/crank/cam/O2 category listings with fitment · fcpeuro.com · vendor-doc · retrieved 2026-10-25
  4. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  5. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  6. Nexus R3 wiring diagram (HT-193000_WD) · Haltech · vendor-doc · retrieved 2026-10-27
  7. EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-10-27
  8. Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
  9. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-10-27
  10. HP / Dominator EFI wiring manual 199R10555 · Holley · vendor-doc · retrieved 2026-10-27

Not yet indexed: fewer than 3 FAQs.