240Z LS Swap: Mounts, Crossmember Kits, T56, R200 Diff, Chassis and EFI Fuel Guide

A 240Z LS swap is one of the best-supported V8 conversions for the S30, with mount, crossmember and transmission-mount kits from several makers. The main hurdles are the 50-year-old unibody, which often needs rust repair and stiffening, the small R180 rear end, and converting a carbureted fuel system to high-pressure EFI.Medium327612

Difficulty3/5 · ModerateMedium347612
  • Bolt-in engine mounts and complete crossmember kits exist, but the transmission mount usually needs tunnel drilling.
  • Chassis age is the real variable: front frame rails are a common rust point and V8 builds often add stiffening.
  • The carbureted fuel system has no high-pressure pump or adequate return path for EFI.
  • The factory R180 rear and half shafts need an upgrade plan, typically an R200 conversion.
  • Exhaust, cooling and wiring are custom work in every build.

At a glance

The key numbers and parts, with the source on each tile.

Stock engine (240Z)
  • L24 2.4 L inline-six with twin SU-type carburetors
  • Nissan rated it at 151 hp (SAE gross) and 146 lb-ft198 N·m
Sourced · medium1
Curb weight
  • 240Z about 2,302 lb1,044 kg
  • The later 280Z about 2,875 lb1,304 kg
We found no sourced figure for net weight change after an LS swap.Sourced · medium1
Shared chassis

Kits cover 240Z, 260Z and 280Z (1970-78), but 240Z tunnels, floor pans and rails differ, so transmission crossmembers are chassis-specific

Sourced34
Mount approach

Plate mounts on the stock front crossmember, or a modified OE crossmember with LS mounts welded on

Sourced253
Oil pan
  • Rear-sump pan
  • Kits name the 1998-2002 F-body (LS1 Camaro) pan or the C6 LS2 Corvette pan
Sourced534
Transmissions
  • T56 or CD009 manual
  • GM automatics from the Powerglide to the 4L80E with some mount kits
Sourced42
Rear end
  • Builders commonly convert the R180 to an R200 using 280Z or ZX parts
  • One autocross build uses a Q45 R200 with custom CV axles
Low confidence129
California

Gasoline vehicles from 1975 and older are exempt from Smog Check, which covers every 240Z

Sourced17

Recommended engines

  • LS1 · Aluminum-block Gen III engine that most S30 mount kits were drawn around; its F-body rear-sump pan is the pan several kits call for.
  • 5.3 LM7 / L59 / LY5 (Gen III/IV truck) · Cheap, plentiful iron-block truck engine; the extra mass sits over the nose of a car that weighed about 2,300 lb (1,044 kg) from the factory.
  • LS3 / L99 · Gen IV 6.2 L sold new as a crate engine with GM installation data; several documented S30 builds use it.
  • LS2 · Aluminum Gen IV 6.0 L; one S30 crossmember kit names the C6 LS2 Corvette pan as compatible.

Mounts

For a 240Z LS swap, most builders buy mounts rather than fabricate them.

Stock-crossmember mounts

Dirty Dingo DD-LS-Z1 bolts to the stock Z crossmember and engine pads, with up to 2 1/2 in (64 mm) forward and 1/2 in (13 mm) rearward adjustment

Sourced2
Crossmember kits
  • Hoke sells a modified OE crossmember with LS mounts plus a T56 transmission mount
  • It needs an S30 crossmember core
Sourced3
Engine position

Range Industries mounts place the engine about 4 in (102 mm) from the firewall

Sourced5

Two approaches exist: plate mounts that bolt to the factory front crossmember and engine pads, or a complete crossmember with LS mounts already welded in place.23

Plate mounts are the cheapest route. Dirty Dingo's laser-cut mounts reuse the stock pads, while the Range Industries pair uses BMW-type rubber isolators and needs a 7/16 in (11 mm) hole drilled in the crossmember for the anti-rotation pin.25

Check accessory-drive fit before you order. Dirty Dingo notes that truck-spacing low-mount A/C forces the engine about 2 1/2 in (64 mm) forward, and that Corvette or Camaro-GTO low-mount A/C will not fit its mounts at all.2

Transmission

The T56 six-speed is the usual manual choice, and both crossmember kits we reviewed are designed around it.

T56 torque rating

1994-2002 F-body T56 units are listed at 450 lb-ft (610 N·m), with a 0.50 sixth gear

Sourced · medium14
Transmission mount
  • Straightboost's mount bolts to the tunnel with sandwich plates and requires drilling
  • Tunnel modification may be needed
Sourced4

Straightboost also lists the Nissan CD009 and asks buyers to contact it for other combinations.34

Owners disagree on tunnel fit. On one forum thread a builder said the T56 went in unmodified, while another said it only fit after hammering the tunnel. Plan for some panel work and test-fit before final paint.Low13

Automatics are common too. Dirty Dingo lists the Powerglide, TH350, TH400, 700R4, 4L60E, 4L65E, 4L70 and 4L80 as compatible, and a documented turbo LS1 Z runs a 4L60E. The 4L60E is listed at 360 lb-ft (488 N·m), below the T56.Medium21015

Clearance

The S30 front crossmember sits where a GM front-sump pan would hit, so every kit we found calls for a rear-sump pan.

Headers

Hoke's kit clears long-tube headers such as Hawk's Third Gen and CX Racing, but not shorty headers

Sourced3
Oil pan

Straightboost fits most rear-sump pans but recommends the LS1 Camaro pan over a truck pan for ground clearance

Sourced4

The F-body pan is the common reference, and Hoke also names the C6 LS2 Corvette pan.534

Match headers to the mount kit. Hoke states its design is drawn for long-tube headers, and Dirty Dingo warns that some alternator brackets limit adjustment. Buy mounts, pan and headers as a set where possible.32

A/C is possible but tight. Hoke says its kit clears the stock or a Sanden compressor, though its bracket to clear the frame rails was still unfinished when we checked.3

Cooling

The L24 radiator was sized for a 2.4 L six.

GM guidance

GM warns that retrofits may need cooling, fuel, electrical and exhaust changes not included with the crate engine

Sourced8
Documented radiator

One LT1-swapped 240Z for sale used a Griffin aluminum radiator and an aluminum water pump

Low confidence11

Plan on an aluminum radiator with electric fans and a shroud, sized to the opening in the radiator support. GM itself warns that crate-engine retrofits may need cooling-system changes.Medium811

Engine position affects radiator room. Mount kits that push the engine forward for A/C clearance reduce the gap between the water pump pulley and the core, so measure before buying a thick radiator.Medium2

Boosted builds need more. The turbo LS1 Z we reviewed adds a V-mount intercooler and an oil cooler, which compete with the radiator for space in the nose.Medium10

Fuel

The 240Z left the factory with carburetors, so its pump, lines and tank were never meant for EFI pressure.

GM fuel requirement (LS3 crate)
  • About 58-60 psi constant pressure400 kPa
  • Pump capable of 45 gph at that pressure170 L/h
GM's sheet quotes both 58 and 60 psi; it says to follow the engine control system's documentation.Sourced8
Surge tank route
  • Stock carbureted pump feeds an engine-bay surge tank
  • A high-pressure pump inside feeds the rail
  • A return line to the tank is required
Sourced6

An LS needs roughly 58-60 psi (400 kPa) at the rail, and GM specifies a pump that can flow 45 gph (170 L/h) at that pressure.18

One common fix is a surge tank. The stock low-pressure pump fills it, a high-pressure pump inside it feeds the injectors, and a return line goes back to the main tank. Z Car Depot's kit also notes that large pumps can overload the stock alternator.6

Other builds replace the tank. One LT1 car uses a custom baffled aluminum tank with 3/8 in hard line and -6 AN fittings, and an LS3 autocross Z uses a 15 gal (57 L) tank. Safety: depressurize before opening any fitting and keep lines away from the exhaust.Low119

Exhaust

No bolt-on cat-back exists for this swap.

Dual exhaust

Hoke designs both its 240Z and 260/280Z transmission crossmembers to allow dual exhaust

Sourced3
Header typeLong-tube headers are the documented fit with crossmember kitsSourced3

Start from headers that suit your mount kit, then build pipework under the floor. The transmission crossmember shape decides whether a true dual system fits.Medium34

Turbo builds route differently. The turbo LS1 car we reviewed uses custom headers and exits through the passenger front quarter panel behind a heat shield.Medium10

Electrical

ECU+ PDM / relaysCrank / cam sensorsThrottle (DBW) + pedalInjectorsCoilsEngine sensorsFuel pumpCooling fansGauges / tachStarter / chargingChassis loads

Match the harness and engine computer to the engine generation.

Crank and cam triggers
  • Gen III (LS1, LM7): 24x crank and rear cam sensor
  • Gen IV (LS2, LS3): 58x crank and front-cover cam sensor
Sourced · medium16
Knock sensors
  • Gen III sensors sit under the valley cover
  • Gen IV sensors sit low on the block sides
Sourced · medium16

Gen III and Gen IV engines use different crank wheels, cam sensor locations and knock sensor positions, so a mixed set of parts will not sync.Medium16

Mount the standalone ECU and any power distribution module (PDM) inside the cabin, such as the passenger footwell, away from engine heat and water. Feed them from a fused main supply, and switch the fuel pump and fans through relays or PDM outputs.Low68

The original Z electrical system was built for a carbureted six. Check alternator capacity against the EFI pump, fans and ignition load. Safety: fuse every new circuit at the battery, and size main cables for starter current.Medium6

Chassis

Start with the shell.

Frame rails
  • The front frame rails are a very common rust point
  • Weld-in repair rails run from the firewall to the radiator support
Sourced7
R200 conversion parts

Forum parts lists name the 280Z R200 mustache bar, companion flange, rear cover and stub axles, plus a curved transverse link

Low confidence12

Front frame rails rot on these cars, and replacement rails are weld-in parts from firewall to radiator support. Fix rust before adding V8 torque, since a weak shell only gets worse under load.7

Most serious LS Zs add stiffening. Documented builds include a custom subframe and roll cage, and one builder describes adding frame rails and cage work. Treat these as engineering decisions, not bolt-ons.Low1013

The rear end is the other weak link. Owners report broken R180s and swap to an R200 with 280Z parts, and some check half shafts for bottoming at full droop. One LS3 autocross Z runs a Q45 R200 viscous LSD with custom CV axles.Low129

Tuning

A matched GM controller and harness is the lowest-risk path for a crate engine.

GM LS3 crate data

The LS3 crate data sheet lists 10.7:1 compression, a 6,600 rpm maximum speed and premium 92 (R+M)/2 fuel

Sourced8
Break-in

GM says to avoid maximum engine speed and long high-load periods for the first 500 miles (12 to 15 engine hours)

Sourced8

A junkyard engine with a standalone ECU gives more freedom but needs a full calibration, starting with fuel delivery, idle and the injector data.Medium8

Log with a wideband oxygen sensor, confirm knock control works, and set a sensible rev limit before any loaded runs. Make ignition changes in small steps with knock monitoring, never copied from another car.Low8

Respect GM's break-in guidance on a fresh engine. A light car reaches high load quickly, so build up gradually and recheck fluids, leaks and temperatures after each session.Medium81

Parts checklist

Tick what you have; the list is saved in this browser.

0 of 23 ticked (saved in this browser)
Mounts
Transmission
Clearance
Cooling
Fuel
Exhaust
Electrical
Chassis
Tuning
Legal

Order of work

10 stages, in the order most builds follow.

  1. Assess the shell and the law
    Inspect frame rails, floors and strut towers for rust, and confirm registration and inspection rules before buying parts.
  2. Choose engine, pan and mounts together
    Pick the engine generation, then a mount kit and rear-sump pan it supports, plus an accessory drive that does not fight the mounts.
  3. Repair and stiffen the chassis
    Replace rotten rails and floors while the bay is empty, and add any stiffening you plan to run.
  4. Prepare the engine on a stand
    Fit the pan and pickup, clutch or flexplate, starter and accessory drive. Support the engine securely on the hoist when lifting.
  5. Install the drivetrain
    Fit the crossmember or mounts, lower the engine and gearbox, then drill and fit the chassis-specific transmission mount.
  6. Upgrade the rear end
    Convert to an R200 with the matching mount, cover, flanges and axles, then order a driveshaft to measured length.
  7. Build fuel and cooling
    Install the EFI pump, surge tank or new tank, return line and regulator, then the radiator, fans and hoses.
  8. Fabricate the exhaust
    Fit headers, then route pipework and hangers under the floor around the transmission crossmember.
  9. Wire and start
    Mount the ECU in the cabin, run fused power, relays and grounds, prime oil and fuel, then check for leaks and trigger sync.
  10. Calibrate and shake down
    Log with a wideband, verify knock control and temperatures, follow break-in guidance, and build load gradually.

Common problems

Symptom, cause and the usual fix.

ProblemCauseFix
Engine sits further forward than plannedTruck-spacing low-mount A/C brackets seat against the mounts and push the engine forward.Choose an accessory drive the mount maker lists as compatible, or accept the forward position and recheck radiator room.2
Oil pan hits the crossmemberA front-sump or deep truck pan is fitted where the S30 crossmember sits.Use the rear-sump pan named by the mount kit, such as the 1998-2002 F-body pan.54
Shorty headers will not clearCrossmember kits are drawn around long-tube header paths.Use long-tube headers the kit maker lists, or confirm fit before buying.3
Engine leans out or stumbles under loadThe carbureted pump, small return line or unbaffled tank cannot hold EFI pressure.Fit a surge tank or baffled tank with a high-pressure pump and an adequate return line.Medium68
Broken differential or half shaftsThe stock R180 and its shafts were built for a 2.4 L six.Convert to an R200 with LSD and check shafts for bottoming at full droop, or fit custom CV axles.Low129
Body flex, cracked paint or doors that bindRusted rails or an unstiffened unibody under V8 torque.Repair rust first, then add frame connectors or a cage as the power level demands.Low713

Frequently asked

What mount kit do you need for a 240Z LS swap?

You need either plate mounts that bolt to the stock crossmember or a complete crossmember kit. Dirty Dingo and Range Industries sell stock-crossmember mounts; Hoke and Straightboost sell kits with transmission mounts. All call for a rear-sump oil pan, and transmission mounts are chassis-specific because 240Z and 260/280Z tunnels differ.2534

Does a T56 fit in a 240Z?

Yes, and it is the most common manual choice. Crossmember kits are designed around it, but the transmission mount bolts through the tunnel and usually needs drilling. Owners disagree on whether the tunnel itself needs reshaping; some report a clean fit and others needed hammering, so test-fit before paint.Medium4133

Will the stock R180 differential handle an LS?

Not reliably. Owners report breaking R180s and converting to an R200 using the 280Z mustache bar, companion flange, cover and stub axles. Check half shafts for bottoming at full droop afterward. Higher-output builds often move to a Q45 R200 limited-slip unit with custom CV axles.Low129

Do you need frame connectors on an LS 240Z?

Often, depending on power and chassis condition. Front frame rails are a common rust point, so repair comes first. Documented builds add custom subframes, frame rails and roll cages, and owners describe noticeable flex in unstiffened cars. Treat stiffening as part of the plan for anything beyond a mild street engine.Low71013

How do you convert a carbureted 240Z fuel system for an LS?

Add a high-pressure pump and a return path. GM's LS3 crate sheet calls for roughly 58-60 psi (400 kPa) and a pump able to flow 45 gph (170 L/h). A common route is an engine-bay surge tank fed by the stock pump, with a return line to the tank; others fit a new baffled tank.8611

Is an LS-swapped 240Z smog exempt in California?

Yes for Smog Check. The California DMV exempts gasoline vehicles from 1975 and older, which includes every 1970-73 240Z. Registration, equipment and noise rules still apply, so keep the car road-legal in other respects. This is general information, not legal advice; check current rules before you build.17

Related

Sources

22 sources
  1. Nissan S30 · Wikipedia · reference · retrieved 2026-10-27
  2. LS Datsun 240Z/260Z/280Z ('70-'78) Motor Mounts, Dirty Dingo DD-LS-Z1-PC (retailer listing) · PSI Conversion · vendor-doc · retrieved 2026-10-27
  3. 240/260/280z LS/T56 Mounting Kit · Hoke Performance · vendor-doc · retrieved 2026-10-27
  4. LS Engine Swap Mount Kit for Datsun 240Z/260Z/280Z · Straightboost Performance · vendor-doc · retrieved 2026-10-27
  5. Datsun 240Z LS Engine Mounts · Range Industries · vendor-doc · retrieved 2026-10-27
  6. Fuel Pump Surge Tank EFI 240Z 260Z 280Z 510 · Z Car Depot · vendor-doc · retrieved 2026-10-27
  7. Premium Front Frame Rail Kit 70-78 240Z-260Z-280Z (30-7314) · The Z Store · vendor-doc · retrieved 2026-10-27
  8. LS3 EFI Crate Engine Specifications and Installation Instructions (19419889) · Chevrolet Performance (hosted by Speedway Motors) · oem · retrieved 2026-10-27
  9. David Carroll's 1975 Datsun 280Z: 2016 OUSCI Recap · OPTIMA Batteries · press · retrieved 2026-10-27
  10. Shooting Star: An LS-Swapped 240Z That's Burning Brightly · Driving Line · press · retrieved 2026-10-27
  11. 1972 Datsun 240Z V8 Swap (sale listing) · Built for Backroads · community · retrieved 2026-10-27
  12. R200 diff axles (forum thread) · HybridZ · community · retrieved 2026-10-27
  13. Advice/recommendations for LS 240Z (forum thread) · HybridZ · community · retrieved 2026-10-27
  14. Tremec T-56 transmission · Wikipedia · reference · retrieved 2026-10-27
  15. GM 4L60-E transmission · Wikipedia · reference · retrieved 2026-10-27
  16. Dialing In LS Sensors For Various Generations · EngineLabs · press · retrieved 2026-10-27
  17. Smog Inspections · California Department of Motor Vehicles · standard · retrieved 2026-10-27
  18. Tampering Policy: The EPA's Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices (Nov 2020) · US Environmental Protection Agency · standard · retrieved 2026-10-25
  19. Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-27
  20. Change vehicle details on a V5C registration certificate (log book) · GOV.UK / DVLA · standard · retrieved 2026-10-25
  21. StVZO § 19 Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
  22. VSB 14 National Code of Practice for Light Vehicle Construction and Modification, Section LA: Engines · Queensland Department of Transport and Main Roads · standard · retrieved 2026-10-25