Early Bronco Coyote Swap (1966-77): Mounts, 6R80 and Dana 20 Adapters, Fuel, Ford Performance Control Pack and Legal Guide

A Coyote swap into a 1966-77 Bronco is the signature restomod build, with adapters, crossmembers and radiators sold for it. It takes Coyote engine mounts, a 6R80 or manual with a Dana 20 or Atlas adapter, new driveshafts, a return-style EFI fuel system and complete engine controls. The main hurdles are mounts and pan clearance, the transmission package and wiring the controls pack.Medium51213

Difficulty4/5 · HardMedium531316
  • Transmission adapters, a 6R80 crossmember and a radiator are sold, but we found no published Coyote engine mount or oil pan specifically listed for the early Bronco.
  • The 6R80 crossmember is a tight fit around the Dana 20 and needs custom exhaust routing.
  • Ford's controls pack requires a return-style fuel system at 55 psi (3.8 bar) and an in-tank pump is strongly preferred.
  • The Coyote is just over 29 in (737 mm) wide, which crowds the brake booster and steering in a small engine bay.
  • Every gauge signal and the transmission controller have to be planned from scratch.

At a glance

The key numbers and parts, with the source on each tile.

Factory engines
  • 170 and 200 cu in sixes
  • 289 V8 from 1966, 302 V8 from 1969 to 1977
Sourced · medium18
Driveline

Dana 20 transfer case, Dana 30 front axle (Dana 44 from 1971), Ford 9-inch rear

Sourced · medium18
Wheelbase92in2,337 mmSourced · medium18
Coyote size
  • Just over 29 in wide737 mm
  • About 430 lb as weighed by EngineLabs195 kg
Sourced · medium16
Automatic route

4WD-case 6R80 with Advance Adapters 50-3901 to the Dana 20 and crossmember 716040

Sourced12
Manual route

Advance Adapters 27-3525C: AX15 five-speed, Coyote bellhousing with hydraulic clutch and Dana 20 adapter

Coyote motor mounts are not included.Sourced4
Fuel (Ford controls pack)

Return-style, 55 psi (3.8 bar) referenced to manifold vacuum, pump of at least 155 L/h at 55 psi

Sourced13
Cooling

Aluminum Coyote-swap radiators that drop into the stock V8 core support are sold

Sourced · medium7
California smog

DMV lists 1975-and-older gasoline vehicles as exempt from Smog Check

Sourced20

Recommended engines

  • Coyote Gen 2 · Port injection only, and Ford Performance sells 2015-17 controls packs for manual and automatic; a press-featured 1976 Bronco runs a Gen 2 with a Ford Performance computer and harness.
  • Coyote Gen 1 · Cheapest 2011-14 donors with simple port-injected controls, but Ford's 2011-14 controls pack supports manual transmissions only, which matters if you want a 6R80.
  • Coyote Gen 3 · Adds direct injection alongside port injection, so it needs high-pressure pump and DI injector control; only worth it if the controls budget covers that.
  • Coyote Gen 4 · Sold new as a Ford Performance crate engine, the cleanest documented starting point for a restomod; it is also dual-injection and the most expensive route.

Mounts

A Coyote swap Bronco build on the 1966-77 truck is well supported on the transmission side, but engine mounts are the gap.

Mounts in the AX15 kit

Advance Adapters states its Bronco Coyote AX15 kit does not include Coyote motor mounts

Sourced4
Factory-style V8 mounts
  • Small-block Ford mounts and weld-on frame towers are sold for 1966-77 Broncos
  • None we found list the Coyote
Sourced · medium8
Full chassis option

Roadster Shop's 1966-77 Bronco IFS chassis includes Coyote and LS engine mounts

Sourced · medium12

Advance Adapters says its Coyote AX15 kit leaves out motor mounts, and the specialist catalogs we checked list mounts and towers only for small-block Ford V8s.Medium485

That leaves three routes

A Coyote mount kit from a Bronco specialist (confirm fitment for your frame and transmission), fabricated weld-on mounts, or a complete replacement chassis. Roadster Shop's IFS chassis for 1966-77 Broncos comes with Coyote mounts and a center crossmember for a 6R80 and Atlas transfer case.Low128

Set engine position with the transmission and transfer case adapter in place, because the 6R80 crossmember bolts into the stock frame holes and fixes the rear of the package. Then check the front of the engine against the radiator and the pan against the front axle.Medium316

Transmission

The common automatic is the 6R80, but it must be the 4WD version.

6R80 to Dana 20 adapter (50-3901)
  • For the 4WD 6R80 only
  • The 10R80 shares the bolt pattern
  • Includes the spud shaft, bearing retainer and sealed bearing
Sourced1
6R80 data
  • About 215 lb98 kg
  • 590 lb-ft input torque rating per Advance Adapters800 N·m
  • 23.75 in long603 mm
Sourced · medium16
Dana 20 low range2.46:1 on early units, 2.34:1 from early 1973Sourced4
Ford Gen 1 controls packManual transmission onlySourced15

Advance Adapters' 50-3901 mates a 4WD 6R80 or 10R80 to the Dana 20 with a new spud shaft, and its 716040 crossmember replaces the stock member. Wild Horses sells the same parts plus an Atlas adapter.125

For a manual, Advance Adapters' 27-3525C kit pairs a new AX15 five-speed with a Coyote bellhousing, hydraulic clutch and Dana 20 adapter. Its shifter bracket suits the T-style transfer case shifter of 1966-72 trucks; 1973-77 J-pattern shifters are harder to keep, and twin-stick shifters are the usual fix.4

Press-featured builds also used a 4R70 automatic, and a 1976 build ran a 6R80 with a Lokar electronic shifter and a twin-stick Dana 20. Whatever you pick, measure front and rear driveshafts only after the drivetrain sits on its final mounts.Medium1011

The 6R80 needs a controller. Ford's automatic controls pack PCM plugs into a 2015-17 Mustang transmission connector, while the Bronco needs a 4WD-case 6R80, so confirm compatibility with Ford. Wild Horses also lists standalone Quick 6 controllers for 6R80 Coyote swaps.Medium1315

Clearance

The early Bronco bay was built for a small-block Ford, and the four-cam Coyote is just over 29 in (737 mm) wide.

WidthJust over 29 in across the cam covers737 mmSourced · medium16
Height

About 20.5 in (521 mm) from crank centerline to the top of a Boss 302 intake

Sourced · medium16
Crossmember fit
  • Tight between transmission and transfer case
  • Notched for the Dana 20 front output retainer bolt
Sourced3

Check the brake booster, steering shaft and inner fenders before final placement; press-featured builds moved to hydroboost brakes and an electric steering assist.Medium161011

Check the oil pan against the front axle differential and tie rod at full suspension compression. We found no published pan clearance for a Coyote over the Bronco's Dana 44, so mock up with the axle stuffed, and confirm any swap pan's sump position before buying.Low1816

The 6R80 crossmember may need welds on the inside of the frame rails ground off, and frame width varies with age. Advance Adapters oversizes and slots its holes to absorb that variation.3

Cooling

The early Bronco's small nose leaves little room for a big core.

Swap radiator

Aluminum radiator for 1966-77 Bronco Coyote swaps, with or without an integrated automatic transmission cooler

Sourced · medium75
CapWild Horses recommends a 16 lb anti-electrolysis capSourced · medium7
Fan control in Ford's packDedicated fan output with a 10 AWG blunt-cut leadSourced13

Wild Horses sells aluminum Coyote-swap radiators that drop into the stock V8 core support with separate mounts, in versions with and without an automatic transmission cooler.Medium75

Run an electric fan with a full shroud; one documented 1976 build used a 16 in (406 mm) brushless fan. Ford's pack provides a fan output, so wire the fan through a relay fed from a fused supply.Medium1113

Slow off-road work heats the transmission. Use the radiator's cooler or add a separate one, and route the degas bottle so the system can be bled from its highest point.Low7

Fuel

Ford's controls pack will not run on a returnless system.

Regulated pressure

55 psi (3.8 bar) across the injector, regulator referenced to manifold vacuum

Sourced13
Pump flowAt least 155 L/h (41 US gal/h) at 55 psiSourced13
System type
  • Return-style
  • Ford's calibration will not work with a returnless system
Sourced13
Bronco EFI tanks

Stainless 23 gal EFI tank with in-tank pump, and EFI pump kits for that tank, are sold for 1966-77 Broncos

Sourced · medium9

It needs a return-style setup with a vacuum-referenced regulator at 55 psi and a pump that flows at least 155 L/h at that pressure, so the factory carbureted tank and mechanical pump are both replaced.13

Put the pump in the tank. Ford warns that a pump pulling fuel can cavitate as heat rises and send vapor to the injectors, and its instructions name pavement versus trail heat as a factor. EFI tanks with in-tank pumps are sold for the early Bronco.139

If you must use an external pump, Ford suggests about 100 micron filtration before it and about 10 micron after. Safety: wire an inertia switch into the pump circuit, depressurize before opening lines, and leak-check the whole system with the key on before starting.13

Exhaust

Plan the exhaust around the 6R80 crossmember.

Crossmember routing
  • Driver-side pipe runs under the 6R80 crossmember and passenger-side pipe inside it
  • Custom routing is required
Sourced32
Oxygen sensors

Ford's manual and automatic harnesses use different oxygen sensor locations

Sourced13

Advance Adapters routes the driver-side pipe under it and the passenger side inside it, and says custom routing is required. Documented builds used shorty headers into 3 in (76 mm) pipe.Medium321110

Keep headers clear of the steering gear, starter and frame, and place each bank's oxygen sensor where Ford's harness expects it. Ford notes that its manual and automatic engine harnesses place the sensors differently, so match headers to the harness.Medium13

Electrical

ECU+ PDM / relaysCrank / cam sensorsThrottle (DBW) + pedalInjectorsCoilsEngine sensorsFuel pumpCooling fansGauges / tachStarter / chargingChassis loads
Not supported by Ford's packCruise control and air conditioningSourced13
Keep-alive powerMust be hot at all times or stored adaptive data clearsSourced13
Ground qualityUnder 0.1 ohm from battery negative to the chassis ground pointSourced13
GaugesDocumented builds used Dakota Digital gauge packagesSourced · medium1011

Ford Performance's 2015-17 controls pack (M-6017-M50A automatic, 504V manual) includes the PCM, pedal, oxygen sensors, MAF air box and harness. The PCM must mount close to the engine because of harness length, and a clutch bottom-of-travel switch acts as the starter interlock on manual cars.1314

On the truck side you wire ignition and start feeds, a fuel pump output with its own ground, the fan lead, the pack's own check-engine lamp and constant keep-alive power. Ford warns that an intermittent ignition feed reads as a shutdown request, so use one reliable source.13

A 1970s Bronco cluster cannot read modern signals directly. Documented builds fitted Dakota Digital gauges; if you keep factory-style gauges, an interface such as the SGI-100BT can rescale speed and tach signals. Safety: fuse every high-current feed near the battery.Medium101119

Chassis

Front suspensionCoil-sprung solid axle located by radius arms and a track barSourced · medium18
Documented brakesWilwood four-wheel discs with hydroboost on a Coyote restomodSourced · medium10
1980-96 full-size Bronco

Different truck: 104-104.7 in wheelbase, Twin Traction Beam front on 1980-86, 4,343-4,374 lb (1,970-1,984 kg) curb weight

Sourced · medium18

Documented Coyote Broncos kept the Dana 44 front and 9-inch rear but rebuilt them, and paired the swap with a 3.5 in (89 mm) lift, new radius arms and four-wheel disc brakes. Treat brakes and steering as part of the swap.Medium1110

This guide covers the 1966-77 early Bronco. The 1980-96 full-size Bronco is a different truck with a longer wheelbase, different transfer cases and, on early models, Twin Traction Beam front suspension, so none of the adapters and crossmembers above apply to it.Medium181

Tuning

Ford's pack is calibrated for its crate engine with the supplied air box and MAF.

Load sensing in Ford's pack
  • Air box with integral MAF, used as supplied
  • A different inlet needs calibration
Sourced13
MAF placement guidance

At least 6-8 in (150-200 mm) upstream of the throttle, and no more than 24 in (610 mm)

Sourced13
Fuel gradePremium, 91 octane (AKI) or higher, for Ford's calibrationSourced13

The Bronco's short nose often tempts builders to reroute the intake, but Ford states a different inlet needs a calibration change, so plan the intake around the supplied parts.13

Calibrate the transmission for tire size and axle ratio, then confirm the speed signal before setting shift points. Log cam angle, knock activity and wideband lambda together, and keep any ignition changes conservative and knock-led.Low1317

Parts checklist

Tick what you have; the list is saved in this browser.

0 of 22 ticked (saved in this browser)
Mounts
Transmission
Clearance
Cooling
Fuel
Exhaust
Electrical
Chassis
Tuning
Legal

Order of work

10 stages, in the order most builds follow.

  1. Check the law and choose the package
    Confirm your truck's smog status, then pick engine generation, transmission and controls together.
  2. Source mounts and adapters
    Confirm mount fitment, and order the transfer case adapter and crossmember for your transmission.
  3. Strip the truck
    Disconnect the battery, remove the old engine, transmission, fuel tank and engine wiring.
  4. Mock up the drivetrain
    Fit transmission, adapter and Dana 20, bolt in the crossmember, then set engine position on its mounts.
  5. Check clearances
    With the axle at full compression, check pan, steering, booster and exhaust paths before welding anything.
  6. Driveshafts and shifters
    Measure and order front and rear driveshafts; fit the transmission and transfer case shifters.
  7. Fuel and cooling
    Install the EFI tank, return-style regulator and lines, then the radiator, fan and transmission cooling.
  8. Exhaust
    Fit headers and route pipes around the crossmember, with oxygen sensors where the harness expects them.
  9. Wire the controls
    Install the controls pack, power distribution and gauges, with reliable ignition and keep-alive feeds.
  10. First start and calibration
    Pressure-test fuel, bleed cooling, start and check for leaks, then confirm speed signal and log before off-road use.

Common problems

Symptom, cause and the usual fix.

ProblemCauseFix
Engine will not start with Ford's controls packReturnless or low-pressure fuel systemFit a return-style system with a vacuum-referenced regulator at 55 psi and confirm rail pressure while cranking.13
Engine shuts off over bumps or after a hard launchIntermittent ignition-run feed to the PCMFeed the run circuit from one reliable switched source and secure the connectors.13
6R80 crossmember will not slide between the frame railsOld frame welds on the inner rails and frame width variationGrind the welds flush and use the crossmember's oversized and slotted holes to align it.3
Wrong 6R80 bought for the adapterA 2WD case was used; the Dana 20 adapter is for the 4WD 6R80 onlySource a 4WD 6R80 or 10R80 before ordering adapters.1
Lean stumble on hot daysFuel pump cavitation from an external pump pulling fuelMove to an in-tank pump; if external, use coarse pre-filtration and fine post-filtration as Ford describes.13
Transfer case shifter will not fit with the manual kit1973-77 J-pattern shifter linkageConvert to T-style shifter rods or fit a twin-stick shifter.4

Frequently asked

Will a Coyote fit in an early Bronco?

Yes, with work. Transmission adapters, a 6R80 crossmember and Coyote-swap radiators are sold for 1966-77 Broncos, and press-featured builds run Coyotes on stock frames. Engine mounts are the gap: Advance Adapters' manual kit excludes them, so you source a Bronco Coyote mount kit, fabricate mounts or buy a replacement chassis.Medium1274

What transmission do you use for a Coyote swap Bronco?

Most builds use a 4WD 6R80 automatic with an adapter to the Dana 20 or an Atlas, plus a new crossmember. The 10R80 shares the bolt pattern. For a manual, Advance Adapters sells an AX15 kit with a Coyote bellhousing and hydraulic clutch. Some restomods also ran a 4R70 automatic.Medium1410

Can I keep the Dana 20 transfer case with a Coyote?

Yes. Advance Adapters sells adapters from the 4WD 6R80 and 10R80, and from the AX15 manual, to the early Bronco's Dana 20, and a press-featured 1976 build kept a rebuilt Dana 20 with a twin-stick shifter. The 6R80 crossmember is notched to clear the Dana 20 front output retainer bolt.14113

What fuel system does a Coyote Bronco need?

A return-style EFI system. Ford's controls pack needs 55 psi across the injectors from a vacuum-referenced regulator and a pump flowing at least 155 L/h at that pressure, and its calibration will not run returnless. Ford prefers an in-tank pump to avoid cavitation, and EFI tanks with in-tank pumps are sold for early Broncos.139

Does the Ford Performance control pack work in a Bronco?

It is designed to let Ford's crate engine run in the application of your choice, and a press-featured 1976 Bronco uses a Ford Performance computer and harness. Plan for its rules: return fuel at 55 psi, the supplied MAF air box, no cruise control or A/C support, and a transmission controller that suits a 4WD-case 6R80.Medium13111

Is a Coyote swapped early Bronco smog legal?

In California, 1966-75 Broncos are exempt from Smog Check because DMV exempts 1975-and-older gasoline vehicles. 1976-77 trucks stay in the program, and an engine change there needs a BAR Referee inspection. Federal and overseas rules differ. This is general information, not legal advice; confirm with your authority.2021

Related

Sources

25 sources
  1. 6R80 to Bronco Dana 20 Adapter (50-3901) · Advance Adapters · vendor-doc · retrieved 2026-10-27
  2. Bronco 6R80 Crossmember Kit (716040) · Advance Adapters · vendor-doc · retrieved 2026-10-27
  3. Crossmember Assembly for the 6R80 into 1966-77 Ford Broncos, P/N 716040, instructions (Advance Adapters document) · Advance Adapters (hosted by Wild Horses 4x4) · vendor-doc · retrieved 2026-10-27
  4. AX15 Transmission and Bronco Dana 20 Coyote Adapter Kit (27-3525C) · Advance Adapters · vendor-doc · retrieved 2026-10-27
  5. 1966-77 Early Bronco Coyote 5.0 swap parts · Wild Horses 4x4 · vendor-doc · retrieved 2026-10-27
  6. Dana 20 Transfer Case Adapter, Ford 6R80 4WD (Coyote Swap) · Wild Horses 4x4 · vendor-doc · retrieved 2026-10-27
  7. Aluminum Radiator for Coyote Swap, 1966-77 Ford Bronco · Wild Horses 4x4 · vendor-doc · retrieved 2026-10-27
  8. 1966-77 Early Bronco Motor Mounts · Wild Horses 4x4 · vendor-doc · retrieved 2026-10-27
  9. 1966-77 Early Bronco Fuel System parts · Wild Horses 4x4 · vendor-doc · retrieved 2026-10-27
  10. This Coyote-Swap 1973 RestoMod Is The New Bronco You Need · FordMuscle · press · retrieved 2026-10-27
  11. Coyote V8 Powered 1976 Ford Bronco Built By JRW Rods & Customs · Off Road Xtreme · press · retrieved 2026-10-27
  12. Roadster Shop Introduces 1966-77 Ford Bronco Full IFS 4WD Chassis · Off Road Xtreme · press · retrieved 2026-10-27
  13. M-6017-M50A / 504V 5.0L Controls Pack Instruction Sheet · Ford Performance Parts · oem · retrieved 2026-10-27
  14. Control Pack 2015-2017 Coyote 5.0L with Automatic Transmission (M-6017-M50A) · Ford Performance Parts · oem · retrieved 2026-10-27
  15. M-6017-A504VB 2011-2014 Coyote 5.0L Crate Engine Controls Pack Instruction Sheet · Ford Performance Parts · oem · retrieved 2026-10-25
  16. Ford vs Chevy Comparison: Size, Weight, and HP Per Pound · EngineLabs · press · retrieved 2026-10-25
  17. Ford Coyote engine · Wikipedia · reference · retrieved 2026-10-25
  18. Ford Bronco · Wikipedia · reference · retrieved 2026-10-27
  19. Dakota Digital SGI-100BT speed and tach signal interface (product page) · PSI Conversion · vendor-doc · retrieved 2026-10-27
  20. Smog Inspections · California Department of Motor Vehicles · standard · retrieved 2026-10-27
  21. Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-27
  22. Tampering Policy: The EPA's Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices under the Clean Air Act · U.S. Environmental Protection Agency · standard · retrieved 2026-10-25
  23. Change vehicle details on a V5C registration certificate (log book) · GOV.UK (DVLA) · standard · retrieved 2026-10-25
  24. § 19 StVZO: Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
  25. Vehicle Standards Bulletin 14 (VSB 14): National Code of Practice for Light Vehicle Construction and Modification · Australian Government Department of Infrastructure, Transport, Regional Development, Communications and the Arts · standard · retrieved 2026-10-25