300ZX LS Swap (Z32, 1990-1996): Mounts, Z32 5-Speed or T56, HICAS, Gauges, Differential and Legal Guide

A 300ZX LS swap is a well-supported conversion for the 1990-1996 Z32, with bolt-in mounts, oil pans and gearbox adapters from LOJ Conversions and G Force. The main decisions are keeping the Nissan 5-speed or fitting a T56, which adapter suits a non-turbo or twin-turbo gearbox, and feeding the Z32's hard-wired tach, speedometer and senders.1638

Difficulty3/5 · Moderate13628
  • Z32-specific mounts, oil pans, transmission mounts and adapters bolt in, and LOJ says its GM-gearbox kits need no fabrication beyond tunnel hammering.
  • Adapter choice depends on the gearbox: G Force's adapter fits only the non-turbo 5-speed, LOJ's fits both.
  • The non-turbo fuel pump is too small for LS pressure, and the heater circuit needs a block to stop cavitation.
  • The Z32 is pre-CAN, so gauges run from hard-wired signals rather than network messages, which simplifies integration.

At a glance

The key numbers and parts, with the source on each tile.

Stock engines
  • VG30DE 3.0 L V6 at 222 hp and 198 lb-ft268 N·m
  • VG30DETT twin-turbo at 300 hp and 283 lb-ft, 280 hp with the automatic, per Wikipedia384 N·m
Sourced · medium11
US bodies
  • 1990-1996
  • 2+0 (T-top, non-turbo hardtop, convertible from 1993) and 2+2 T-top
Sourced · medium11
Curb weight (1995, manual)

3,290 lb (1,492 kg) for a US NA 2+0 hardtop to 3,422 lb (1,552 kg) for a US TT 2+0 T-top

Sourced · medium11
Mounts
  • LOJ billet-pedestal mounts with polyurethane inserts
  • G Force GF-Z32MM-KIT with slotted holes
Sourced17
Gearbox optionsNissan RS5R30A 5-speed via adapter, GM T56, or 350Z/370Z CD00xSourced134
Oil panLOJ 6.5 qt baffled steel pan with pickup and dipstick6.2 LSourced1
Driveshaft

New shaft, or stock shaft shortened 3 in (75 mm) with LOJ's Z32-gearbox kit

Sourced1
Electrical architecture

Pre-CAN: tach fed by the engine computer, speedometer by the vehicle speed sensor, gauges by resistive senders

Sourced8
Rear steer
  • Super HICAS on turbo cars
  • The 1996 system uses a motor actuator with steering angle and speed sensors
Sourced119

Recommended engines

  • 5.3 LM7 / L59 / LY5 (Gen III/IV truck) · G Force lists its Z32 adapter for 4.8, 5.3, 5.7, 6.0 and 6.2 L short-crank engines, and LOJ notes most builders find an LS from an automatic vehicle, which its Z32 5-speed kit is designed around.
  • LS1 · Aluminum Gen III engine that LOJ's Gen III/IV mount and pan kits accept; a low-cost choice when you keep the stout Nissan 5-speed.
  • LS3 / L99 · Gen IV 58x drive-by-wire engine; LOJ sells a complete Z32 engine harness built only for Gen IV 58x engines.

Mounts

A 300ZX LS swap is mostly a bolt-in job because two makers sell Z32-specific mounts.

LOJ mounts

CNC-cut and bent brackets, billet aluminum pedestals with polyurethane inserts, powder coated, with hardware

Sourced1
G Force mounts

Powder-coated LS mounts for 1990-1996 Z32 with polyurethane isolators and slotted holes for positioning

Sourced7
LOJ order options2+0 or 2+2, non-turbo or twin-turboSourced1

LOJ Conversions uses bent brackets with billet aluminum pedestals and polyurethane inserts, and G Force sells a powder-coated set with polyurethane isolators and slotted holes for adjusting engine position.17

LOJ sells Basic, Intermediate and higher kit tiers matched to the gearbox you keep. Every tier includes mounts, a swap oil pan, a transmission mount and heater parts, and the Intermediate kit adds an accessory drive for the Nissan power steering pump and alternator, an oil pressure sender adapter and a fuel conversion.12

LOJ's order form asks for 2+0 or 2+2 and non-turbo or twin-turbo, so confirm your exact car before ordering. Sikky's Nissan kit lineup page lists no 300ZX kit, so the Z32 market is narrower than the 350Z's.114

Transmission

Keeping the Nissan 5-speed is the most common Z32 route.

Factory gearboxes
  • RS5R30A 5-speed manual
  • RE4R01A and RE4R03A 4-speed automatics
Sourced · medium11
LOJ Z32 adapter
  • Adapter plate and billet flywheel
  • Gearbox moves 3 in rearward75 mm
  • NA clutch required with either NA or TT gearbox
Sourced1
G Force Z32 adapter
  • Adapter, steel flywheel and pilot bushing adapter
  • Non-turbo gearbox only
Sourced6

LOJ's adapter suits the non-turbo or twin-turbo gearbox, though a non-turbo case needs slight bellhousing clearancing. G Force's adapter fits only the non-turbo gearbox, because the twin-turbo bellhousing puts the starter too far from its flywheel's ring gear.16

LOJ moves the gearbox 3 in (75 mm) rearward and supplies a shortened shift linkage to keep the lever in the stock spot. Shorten the stock driveshaft by the same amount or buy a new one, and expect to dent a small tunnel area for the speed sensor and clearance the starter.1

A GM T56 needs tunnel hammering at the bellhousing transitions, per LOJ, but the dash and under-dash structure stay. A GTO shift linkage puts the lever in the stock location, an F-body linkage lands ahead of it, and LOJ warns the T56 throwout bearing is not compatible with the Nissan master cylinder.3

A 350Z or 370Z CD00x is a third option; LOJ's kit includes an adapter, flywheel and mini starter, but the shifter still sits 2.5 in (64 mm) behind stock. The Z32 automatics bolt to LOJ's plate but need a standalone transmission controller, because the GM computer cannot run them.41

Clearance

Use the pan sold with the mounts.

Oil pan
  • LOJ 6.5 qt zinc-plated steel pan with road-race and anti-slosh baffles6.2 L
  • 6.0-7.0 qt depending on filter relocation and cooler
Sourced3
Tunnel
  • Z32 gearbox: a 2 x 2 in (51 x 51 mm) dent for the speed sensor
  • GM gearboxes: hammer the bellhousing transitions
Sourced13

The LOJ pan is built for its engine height, holds about 6.5 qt (6.2 L) with road-race and anti-slosh baffling, and its final capacity changes with LOJ's optional oil filter relocation kit or an oil cooler.3

LOJ says its GM-gearbox kits need no fabrication beyond tunnel hammering, and the dash does not come out. With the Nissan gearbox, the only body change is a small dent under the passenger seat area for the speed sensor, plus starter clearancing.31

Check the steering shaft, brake lines and starter against the headers at mock-up, before final tightening. Swap heights are set by the mount kit, so mixing mounts and pans from different makers removes the clearance work the kit maker already did.Medium17

Cooling

The Z32 heater circuit needs attention.

Heater circuit

LOJ includes a heater block and heater core outlets to stop cavitation-induced overheating from the Nissan heat control valve

Sourced1
Temperature gauge

Reads a resistive thermal transmitter whose resistance falls as coolant warms

Sourced8

LOJ includes a heater block in every kit to prevent cavitation-induced overheating caused by the Nissan heat control valve, plus outlets to join the LS to the heater core.1

The basic kits we reviewed do not include a radiator or fans, so size them for the engine, climate and A/C. Plumb the LS steam port to a high point, bleed the system on first fill, and switch fans from the new engine computer or a relay or power module.Medium117

The factory temperature gauge reads a thermal transmitter whose resistance drops as coolant warms. Fit a compatible sender in the LS, then compare the gauge with a scan tool reading before trusting it.8

Fuel

Non-turbo cars need a new pump.

Non-turbo pump

LOJ says non-turbo Z32 pumps cannot supply enough fuel at the LS base pressure of 58 psi (4 bar)

Sourced2
LOJ fuel conversion

Returnless conversion with an OEM-style GM filter/regulator and pre-cut lines with quick-disconnect fittings

Sourced2

LOJ says the stock non-turbo Z32 pump cannot supply enough fuel at the LS base pressure of 58 psi (4 bar) and offers a drop-in replacement. Check any twin-turbo pump with the fuel pump flow calculator too.2

LOJ's Intermediate kit converts the car to a returnless system with an OEM-style GM filter and regulator and pre-cut quick-disconnect lines. Keep the evaporative system connected if the car must pass inspection.219

Exhaust

Headers are an option on LOJ's Z32 kits, so choose them with the mounts and gearbox.

HeadersOffered as an option on LOJ's Z32 kits rather than includedSourced1
Emissions hardware

LOJ's Gen IV harness is for non-emissions vehicles, with no air pump or EGR provisions

Sourced5

Check every tube against the steering shaft, the starter and the gearbox at mock-up, since LOJ's Z32-gearbox kit already moves the starter rearward.Medium1

Keep catalysts and oxygen sensors where your jurisdiction requires them. LOJ notes its Gen IV harness is built for non-emissions vehicles with no air pump or EGR provisions, which matters for any inspection.Medium518

Electrical

ECU+ PDM / relaysCrank / cam sensorsThrottle (DBW) + pedalInjectorsCoilsEngine sensorsFuel pumpCooling fansGauges / tachStarter / chargingChassis loads

Unlike the 350Z or RX-8, the Z32 is not a CAN-bus car.

Network

Pre-CAN: the 1996 service manual shows the meter's gauges hard-wired to sensors and the engine computer

Sourced8
Speed signal

The vehicle speed sensor feeds the meter, which passes speed to the engine computer, A/T, power steering, HICAS and cruise control

Sourced8
Anti-theft
  • The theft warning system disconnects the starting circuit
  • It is not an engine-computer immobilizer
Sourced8

Nissan's 1996 service manual shows the tachometer reading a signal from the engine computer, the speedometer reading the gearbox's speed sensor, and the temperature, oil pressure and fuel gauges reading resistive senders.8

That makes the cluster easier to keep. Feed the tach a signal from the new engine computer and confirm it against a scan tool, and fit the Nissan oil pressure sender to the LS with an adapter, as LOJ's Intermediate kit does. The turbo boost gauge reads its own sensor.Medium82

The speed signal matters beyond the speedometer. The meter passes road speed on to the engine computer, transmission, speed-sensitive power steering, HICAS and cruise control, so a gearbox change can affect several systems; LOJ's Z32-gearbox kit keeps the factory sensor.891

ABS and anti-theft stay independent. The ABS wiring diagram shows battery, ignition, brake-switch and wheel-sensor inputs, and the theft system cuts the starter circuit rather than an engine computer. LOJ's Gen IV harness keeps the factory starter and alternator harness and requires GM anti-theft removal.Medium1085

Chassis

Check the rear end before planning gearing.

Differential
  • Forum reports: every Z32 has a viscous LSD
  • NA cars an R200 (4.09), twin-turbo cars a larger R230 (3.69)
  • Posters disagree
Low confidence13
Super HICAS
  • Rear steer with its own control unit, steering angle sensor and speed input
  • Later versions use an electric actuator
Sourced129
Wheelbase96.5 in for 2+0 and 100.4 in for 2+22,450 mm · 2,550 mmSourced · medium11

Forum members agree every Z32 has a viscous limited-slip unit but disagree on details; one moderator lists the non-turbo unit as an R200 with 4.09 gears and the twin-turbo unit as a larger R230 with 3.69 gears. Read the casting and tag on your car.Low13

Super HICAS steers the rear wheels slightly using a control unit, steering angle sensor and vehicle speed. Wikipedia says later versions moved to an electric actuator, and Nissan's 1996 manual shows a HICAS motor on the rear rack; removing the system is a popular aftermarket modification.Medium12911

Weight and wheelbase vary by body. Wikipedia lists 1995 manual cars from 3,290 lb (1,492 kg) to 3,582 lb (1,625 kg), on a 96.5 in (2,450 mm) or 100.4 in (2,550 mm) wheelbase, so give the driveshaft maker your exact body.Medium111

Tuning

GM rating (reference)GM rated the LS1 at 345-350 hpSourced · medium15
Anti-theft

LOJ says all its harnesses require GM VATS removal from the computer

Sourced5

With a donor GM computer, the minimum is a startup calibration that disables GM anti-theft and removes outputs the car no longer has. LOJ requires VATS removal for every Z32 harness it sells and asks for injector, MAF and gearbox details to spec the harness.5

Gen IV engines with Active Fuel Management need it disabled in calibration or hardware. If you keep a Nissan automatic, plan a separate transmission controller, since LOJ notes the GM computer cannot control the Z32 automatics.Medium151

Log with a wideband oxygen sensor before loaded pulls, confirm knock control is active, and set a conservative rev limiter. Change ignition timing in small steps with knock monitoring, never copied from another car.Medium16

Parts checklist

Tick what you have; the list is saved in this browser.

0 of 23 ticked (saved in this browser)
Mounts
Transmission
Clearance
Cooling
Fuel
Exhaust
Electrical
Chassis
Tuning
Legal

Order of work

10 stages, in the order most builds follow.

  1. Check the law and choose the gearbox
    Confirm local rules, then decide between the Nissan 5-speed, a T56 or a CD00x, since that sets the adapter, mounts, driveshaft and tunnel work.
  2. Identify your exact Z32
    Record 2+0 or 2+2, non-turbo or twin-turbo, and the model year, then order parts to match.
  3. Remove the VG30 and its harness
    Pull the engine and gearbox on a hoist with the car on stands, and label the chassis connectors you will reuse.
  4. Fit the mounts, pan and adapter
    Install the swap oil pan, adapter plate, flywheel and clutch on the engine before mounting it.
  5. Install engine and gearbox
    Set the engine on its mounts, fit the transmission mount, dent or hammer the tunnel where the kit says, and fit the shift linkage.
  6. Fit driveshaft, accessories and heater circuit
    Install the new or shortened driveshaft, the accessory drive for steering pump and alternator, and the heater block.
  7. Fit cooling, fuel and exhaust
    Install radiator, fans, pump and regulator, then headers and mid-pipes clear of the steering shaft and starter.
  8. Wire engine and gauges
    Install the LS harness, feed the tach, fit the oil and coolant senders, confirm the speed sensor, and fuse every new feed.
  9. Start, bleed and calibrate
    Load a startup calibration, bleed cooling and clutch, check for leaks, and log with a wideband before loaded driving.
  10. Test HICAS, ABS and certify
    Check ABS and HICAS warning lamps, align the car, then complete the inspection your jurisdiction requires.

Common problems

Symptom, cause and the usual fix.

ProblemCauseFix
Starter will not engage after fitting a G Force adapterA twin-turbo gearbox was used; its larger bellhousing places the starter too far from this flywheel's ring gear.Use a non-turbo gearbox with that adapter, or an adapter designed for both cases.61
Engine leans out or stumbles at load on a non-turbo carThe stock non-turbo pump cannot keep up at the LS base pressure of 58 psi (4 bar).Fit a higher-flow drop-in pump and confirm pressure under load.2
Overheating traced to the heater circuitCavitation caused by the Nissan heat control valve in the LS coolant path.Fit a heater block and the matching heater core outlets.1
Shifter lands ahead of or behind the console openingF-body T56 linkage sits forward; a CD00x sits 2.5 in (64 mm) back even with a shortened linkage.Use a GTO-style T56 linkage or the Nissan 5-speed with LOJ's shortened linkage.34
Clutch will not release with a T56The T56 throwout bearing is not compatible with the Nissan clutch master cylinder.Fit a clutch hydraulics conversion matched to the T56.3
Speedometer, power steering feel or HICAS change after a gearbox swapThe meter relays the speed sensor signal to the engine computer, power steering, HICAS and cruise control.Keep a speed sensor the Z32 meter understands, then confirm speedometer reading and HICAS lamp on a road test.Medium89

Frequently asked

Is there a bolt-in 300ZX LS swap kit?

Yes. LOJ Conversions sells Z32 kits with mounts, a baffled oil pan, a transmission mount and heater parts for the Nissan 5-speed, T56, CD00x or GM automatics, and says its GM-gearbox kits need only tunnel hammering. G Force sells Z32 mounts and a 5-speed adapter separately. Wiring, cooling and exhaust still need planning.1376

Can you keep the 300ZX transmission with an LS swap?

Yes. Adapters mate the LS to the Nissan RS5R30A 5-speed. LOJ's adapter works with non-turbo and twin-turbo gearboxes and moves the gearbox 3 in (75 mm) back, requiring a non-turbo clutch. G Force's adapter fits only the non-turbo gearbox, because the twin-turbo bellhousing puts the starter out of reach.16

Does the 300ZX gauge cluster work after an LS swap?

Usually, with simple wiring, because the Z32 is not a CAN-bus car. Nissan's manual shows the tach fed by an engine-computer signal, the speedometer by the gearbox speed sensor, and the gauges by resistive senders. Feed the tach from the new computer, keep a compatible speed sensor, and adapt the oil and coolant senders.Medium82

Do you need to delete HICAS for an LS swap?

Not necessarily. Super HICAS has its own control unit and uses steering angle and vehicle speed, not engine data, so it can stay if the speed signal is intact. Removing it is a popular modification for other reasons; lock and eliminator kits exist. Test the HICAS warning lamp after the swap.Medium9812

Should you LS swap a twin-turbo or non-turbo 300ZX?

Either works with LOJ's kits, but the details differ. Twin-turbo cars carry Super HICAS and, by forum accounts, a larger R230 rear end, while non-turbo cars need a new fuel pump. G Force's 5-speed adapter suits only the non-turbo gearbox, and LOJ requires a non-turbo clutch whichever gearbox you keep.Medium1261311

Is an LS-swapped 300ZX smog legal?

It can be, but it is not automatic; this is general information, not legal advice. EPA expects the result to match a certified configuration, and California requires a BAR Referee inspection. A 1990-1995 Z32 is within the model-year limit of CARB's GM E-ROD order for a complete E-ROD package, while a 1996 car is not.Medium181920

Related

Sources

23 sources
  1. 300ZX LSx BASIC Swap Kit - Z32 Transmission · LOJ Conversions · vendor-doc · retrieved 2026-10-27
  2. 300ZX LSx INTERMEDIATE Swap Kit - Z32 Transmission · LOJ Conversions · vendor-doc · retrieved 2026-10-27
  3. 300ZX LSx BASIC Swap Kit - T56 Transmission · LOJ Conversions · vendor-doc · retrieved 2026-10-27
  4. 300ZX LSx BASIC Swap Kit - 350Z / 370Z Transmission · LOJ Conversions · vendor-doc · retrieved 2026-10-27
  5. 300ZX LSx Swap Engine Harness - Gen 4 58X Engines · LOJ Conversions · vendor-doc · retrieved 2026-10-27
  6. Z32 5 Speed Transmission Adapter with Flywheel (GF-LSZ32-S) · G Force Performance Products · vendor-doc · retrieved 2026-10-27
  7. 300ZX LS Swap Engine Mounts, 1990-1996 Z32 (GF-Z32MM-KIT) · G Force Performance Products · vendor-doc · retrieved 2026-10-27
  8. 1996 300ZX Service Manual, section EL (Meter and Gauges EL-92 to EL-95; Theft Warning System EL-240 to EL-241) · Nissan Motor Co. · service-manual · retrieved 2026-10-27
  9. 1996 300ZX Service Manual, section ST (Twin Orifice Power Steering ST-27; Super HICAS ST-40 to ST-41) · Nissan Motor Co. · service-manual · retrieved 2026-10-27
  10. 1996 300ZX Service Manual, section BR (Wiring Diagram - ABS - BR-29 to BR-30) · Nissan Motor Co. · service-manual · retrieved 2026-10-27
  11. Nissan 300ZX · Wikipedia · reference · retrieved 2026-10-27
  12. HICAS · Wikipedia · reference · retrieved 2026-10-27
  13. Z32 Lsd (forum thread, 2008) · HybridZ forum · community · retrieved 2026-10-27
  14. Nissan LS Swap Kit Lineup (category page) · Sikky Manufacturing · vendor-doc · retrieved 2026-10-27
  15. General Motors LS-based small-block engine · Wikipedia · reference · retrieved 2026-10-27
  16. Dialing In LS Sensors For Various Generations · EngineLabs · press · retrieved 2026-10-27
  17. Nissan 240SX LS V8 Engine Swap Guide Part 2: Let's Get Started · Speed Academy · press · retrieved 2026-10-25
  18. Tampering Policy: The EPA's Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices (Nov 2020) · US Environmental Protection Agency · standard · retrieved 2026-10-25
  19. Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-25
  20. Executive Order D-126-32: GM LS3 E-ROD engine kit · California Air Resources Board · standard · retrieved 2026-10-25
  21. Change vehicle details on a V5C registration certificate (log book) · GOV.UK / DVLA · standard · retrieved 2026-10-27
  22. StVZO § 19 Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
  23. VSB 14 National Code of Practice for Light Vehicle Construction and Modification, Section LA: Engines · Queensland Department of Transport and Main Roads · standard · retrieved 2026-10-25