At a glance
The key numbers and parts, with the source on each tile.
- 1.3 L Renesis two-rotor
- Wikipedia lists the 6-port at 231-232 hp and the 4-port at 192 hp, with different early North American figures
- Mazda sold the RX-8 from April 2003 and ended production in June 2012
- US model years 2004-2011
- Europe dropped it in 2010
- About 1,309-1,373 kg for manual cars2,886-3,027 lb
- Documented LS cars weighed about 3,200-3,240 lb1,450-1,470 kg
Hinson mounting equipment (some welding), V8 Roadsters tubular subframe, CXRacing bolt-on mounts with rack extension, LS1RX8.com bolt-on kit with drilling
Sourced1101617No transmission mount: a power plant frame (PPF) ties the gearbox to the differential and must be replaced
Sourced · medium19181- Factory electric rack
- Kits lower or extend it, or convert to a modified hydraulic MX-5 NC or RX-7 rack
Recommended engines
- LS1 · The best-documented RX-8 engine: LS1RX8.com calls the 1998-2002 Camaro/Trans Am LS1 and T56 its only direct-fit drivetrain, and the Hinson-kit car LSX Magazine covered uses a Z28 LS1 and T56.
- LS3 / L99 · A Gen IV 58x engine is required by the V8 Roadsters CAN module that keeps the Mazda dash working, and a GRM forum builder documents a crate LS3 with a GTO T56 on the V8R kit.
- 5.3 LM7 / L59 / LY5 (Gen III/IV truck) · The cheap junkyard option, but LS1RX8.com warns the truck intake, oil pan, alternator position and exhaust manifolds all need changing to fit the RX-8 bay.
Mounts
An RX8 LS swap starts with choosing a mounting system, because each kit solves the chassis problems differently.
- Urethane mounts, billet engine stands, tie rod ends, steering adapter, rack mounts, transmission brace with weld-on plates, torque arm
- Front sway bar mounts sold separately
Tubular front subframe with sway bar mounts, engine plates with polyurethane mounts, uni-body supports and transmission crossmember
Sourced10Engine mounts with steering rack extension, T56 mount, subframe and torsion bar bracers, sway bar extension and spacers
Sourced16Hinson and CXRacing keep the Mazda front subframe, V8 Roadsters replaces it with a tubular subframe, and LS1RX8.com sells a bolt-on kit that still needs holes drilled and opened up.1101617
Hinson says the chassis design means some welding, and it supplies directions a fabrication shop can follow. Its package lowers the steering rack to fit the engine under the stock hood, so it includes rack mounts, a steering adapter and bump-steer parts.12
CXRacing lists the known problems as the sway bar and rack hitting the engine and a weak factory subframe and torsion bar brace. Its kit adds bracing and a 5.5 in (140 mm) sway bar extension, and the maker labels it for off-road or track use only.16
Fully custom builds exist too. An Australian 6.0 L Gen IV car used a New Zealand-made engine crossmember and a home-built gearbox crossmember, and its A/C compressor fouled an engine mount.Medium18
Transmission
The RX-8 has no conventional transmission mount.
- GM T56 six-speed
- Hinson sells T56 and 4L60E versions of its mounting equipment
- No transmission crossmember
- The power plant frame bolts the gearbox to the differential
Hinson now sells only an aluminum T56 shaft for its layout, having dropped steel after vibration testing
Sourced8Its power plant frame (PPF) is a beam joining the gearbox to the differential, so a GM gearbox needs its own crossmember and the diff needs separate support. Hinson uses a transmission brace plus a torque arm, and V8 Roadsters removes the PPF and supplies new diff mounting.Medium19110
A poorly engineered PPF delete is expensive. The Street Machine car's first attempt snapped the upper diff support and an axle, and the owner later fitted a stand-alone diff brace while chasing a driveline vibration.Medium18
LS1RX8.com says the T56 shifter falls about 2 in (51 mm) short of the center of the stock opening, so the hole is enlarged, and the clutch master cylinder hole also needs opening up. It recommends fitting the engine first and the gearbox second.Medium17
Plan the driveshaft with the gearbox and rear end. Hinson builds an aluminum shaft for its T56 layout, and V8 Roadsters includes a steel T56 shaft with its Ford 8.8 kit, with an aluminum upgrade.813
Clearance
Truck engines do not drop straight in.
LS1RX8.com lists the truck intake as too tall, the pan as too deep and the alternator as hitting the hood, and recommends LS1 or LS6 intake parts, a Camaro pan and a GTO alternator bracket.Medium17
The steering rack sits close to the sump. V8 Roadsters modifies a hydraulic MX-5 rack so its ports clear the oil pan and says this works only with its subframe, while Hinson lowers the factory rack and restores geometry with a bump-steer kit.122
The ABS hydraulic unit sits where the engine needs room. Hinson calls its relocation bracket a requirement for a street car with ABS, and the Street Machine build moved both the ABS module and its brake lines. Safety: bleed and test the brakes before the car moves under power.Medium918
Check the heads against the firewall seam and the rear coil packs at mock-up. The Street Machine car needed the seam clearanced and one rear coil moved.Medium18
Cooling
Radiator position depends on the kit and the balancer location.
LS1RX8.com reports reusing the factory radiator with modified hoses, while the Street Machine car's balancer hit the core and the radiator moved forward about 6 in (152 mm).Medium1718
Hinson sells a direct-fit dual-pass radiator and fan for its layout. LS1RX8.com notes the RX-8's oil coolers can be reused on the LS, though it considers them unnecessary for street use.417
Fans need a new controller once the Mazda engine computer stops running them. The Street Machine build kept the Mazda computer partly to drive the thermo fans; otherwise switch them from the new engine computer or a relay or power module. Plumb the LS steam port to a high point.Medium1829
Fuel
Size the pump for the LS rather than reusing the rotary's.
Hinson's RX-8 street kit pairs a 255 lph pump with a filter and lines, and the V8 Roadsters package runs braided lines and a filter from the RX-8 tank to the rail. Check capacity with the fuel pump flow calculator.511
Decide where pressure is regulated
Returnless GM rails expect a regulator near the tank, while return-style systems need one in the bay and a return line. Keep the evaporative canister if the car must pass inspection; the Street Machine engineer flagged its position near the diff mount.Medium2918
Exhaust
Plan on swap headers.
- 1 7/8 in 304 stainless long tubes48 mm
- Hinson says stock LS manifolds do not fit with its conversion
1 7/8 in primaries into a 3 in (76 mm) V-band, tested only with its own kit
Sourced · medium17Hinson 3 in (76 mm) stainless Y-pipe clears the T56 and joins stock or aftermarket RX-8 exhaust
Sourced7Hinson says its long tubes are required because stock LS manifolds do not fit with its mounts, and an early custom build used a Camaro header on the right side only, with a fabricated left side.Medium622
Match headers to the mount kit. LS1RX8.com has tested its headers only with its own kit, and V8 Roadsters points package buyers to a fifth-generation Camaro shorty header.Medium1711
Route the Y-pipe past the T56 and the steering shaft, and keep catalysts where the law requires them. Hinson's Y-pipe includes oxygen sensor bungs and connects to a stock or aftermarket RX-8 exhaust.7
Electrical
The RX-8 dash and chassis modules expect CAN messages from the Mazda engine computer.
- The cluster takes engine data from the Mazda computer over CAN
- V8R's module bridges a GM 58x E38 computer to the Mazda dash
Builder report: a base ABS unit works on its own, the DSC unit wants engine inputs, and some ABS unit must stay to feed the dash speed signal
Low confidence19Remove that computer without a replacement and the tach, warning lights and speed-related functions misbehave, which is why the CAN problem dominates RX-8 swap threads.Medium1914
Two routes are documented. One keeps the Mazda computer running the dash, fans, A/C and ABS, fed by a crank trigger on the V8 and Mazda coolant and oil sensors, while a GM-family computer runs the engine. The other uses a CAN module such as V8 Roadsters', which needs a 58x engine.Medium181914
ABS needs care. One builder reports that the DSC version of the ABS unit wants engine inputs that no longer exist, so he fitted a base-model unit with a modified plug, and that some ABS unit must stay because it supplies the dash speed signal.Low19
Electric power steering is the other casualty. CXRacing calls the factory electric rack difficult to make work, and the same builder says keeping it forces the keep-the-Mazda-computer route. Plan steering and dash electronics together, and fuse every new feed at the battery.Low1619
Chassis
The factory differential is strong, but its mounting was designed around a rotary.
- Wikipedia lists a torque-sensing limited-slip as standard
- Documented builds kept the 4.44 or fitted RX-7 3.90 gears
- LS1RX8.com reports hard launches tearing the diff mounting ears off the rear subframe
- S1 and S2 subframes differ at the front diff support
LS1RX8.com says hard launches have torn the diff mounting ears off the rear subframe, and it argues the stock ratios are too short for a V8.Medium17
Many builds change the rear end. V8 Roadsters' two-part kit fits a Ford 8.8 from a 1989-97 Thunderbird, 1993-97 Mark VIII or 2003 Cobra with matched axles, and some covers need fins trimmed to clear the subframe. Others keep the Mazda unit with RX-7 3.90 gears.Medium132218
Check your generation before buying rear parts, because LS1RX8.com says the 2004-08 (S1) and 2009-11 (S2) subframes differ at the front diff support. Budget for brakes and bushings too; documented LS cars weighed about 3,200-3,240 lb (1,450-1,470 kg).Medium172122
Tuning
With a donor GM computer, the minimum is a startup calibration that disables GM anti-theft and removes outputs the car no longer has. If the Mazda computer stays to run the dash, it needs its own crank signal, so confirm both computers agree on engine speed before driving.Medium2618
Gen IV engines with Active Fuel Management need it disabled in calibration or hardware. Drive-by-wire engines need the pedal and throttle body calibrated together with the safety checks left on; V8 Roadsters lists a GM throttle pedal adapter for the RX-8.Medium2715
Log with a wideband oxygen sensor before any loaded pulls, confirm knock control is active, and set a conservative rev limiter. Change ignition timing in small steps with knock monitoring, never copied from another car.Medium28
Legal
This is general information, not legal advice.
EPA treats an engine switch as reasonable if the result matches a certified configuration of the same or newer model year and the same product category
Sourced30Under EPA's 2020 tampering policy, a GM engine in a Mazda chassis rarely matches a certified configuration. California adds a BAR Referee inspection with the donor's emission controls working, and the E-ROD order does not reach a 2004-11 car.303132
In the UK, record the engine change on the V5C and tell your insurer. In Germany, a change that alters the vehicle type or worsens emissions or noise voids the operating permit under StVZO §19 until an inspector approves it.Medium3334
In Australia, VSB 14 Section LA sets the technical rules for engine substitution, with certification run by each state. The Street Machine car was engineered for road use, with only minor items such as the charcoal canister flagged.Medium3518
Parts checklist
Tick what you have; the list is saved in this browser.
Order of work
10 stages, in the order most builds follow.
- Check the law and pick a kitConfirm what your state or country allows, then choose a mount system, because it decides the steering rack, oil pan, headers and sway bar route.
- Plan electronics before buying partsDecide between a CAN module and keeping the Mazda computer, since that choice also decides whether the electric rack and DSC unit can stay.
- Strip the rotary drivetrainSupport the gearbox and differential on jacks, remove the power plant frame, then lower the engine and gearbox. Never work under a car held only by a jack.
- Fit mounts, braces and the steering solutionInstall the engine mounts or subframe, weld any brackets the kit requires, and fit the lowered rack, bump-steer parts or hydraulic rack.
- Install engine, gearbox and diff supportSet the engine in first, then the gearbox, and fit the crossmember and torque arm or new diff mounting before checking driveline angles.
- Relocate the ABS unit and sort clearanceMove the ABS unit and brake lines, check the heads, coils and pan, and refit the front sway bar on its new mounts.
- Fit cooling, fuel and exhaustInstall the radiator, fans, pump, lines, headers and Y-pipe, keeping fuel lines clear of heat and the driveshaft.
- Wire the engine and the dashInstall the engine harness, CAN module or retained Mazda computer, fused main feeds and fan control, then verify every gauge and warning lamp.
- Start, bleed and calibrateLoad a startup calibration, bleed brakes and cooling, check for leaks, and log with a wideband before loaded driving.
- Align and certifySet alignment and bump steer, road test for vibration, then complete the inspection or engineering your jurisdiction requires.
Common problems
Symptom, cause and the usual fix.
| Problem | Cause | Fix |
|---|---|---|
| Tach bounces or warning lights stay on after the swap | The CAN module or calibration does not match the GM computer family; one builder found GM made undocumented changes within computer families. | Use a module the maker has verified with your exact computer, or keep the Mazda computer running the dash.Low1914 |
| Upper diff support or an axle breaks after the PPF is removed | The power plant frame carried the differential's torque reaction and nothing equivalent replaced it. | Fit an engineered torque arm or diff brace, such as the kit makers supply.Medium181 |
| Front sway bar hits the crank pulley or A/C tensioner | The V8 sits where the factory bar runs. | Use the kit's relocation mounts or extension, and check the accessory drive; one builder dropped the A/C tensioner for a stretch-fit belt.Medium19163 |
| Steering rack contacts the engine or oil pan | The factory rack sits in the V8's sump area. | Lower or extend the rack with matching bump-steer parts, or use a modified hydraulic rack built for the kit's subframe.16212 |
| ABS or DSC faults and no speedometer | The DSC unit expects engine data, and the dash speed signal comes through the ABS unit. | Fit a base-model ABS unit with a modified plug, or a CAN module that supplies speed.Low19 |
| Driveline vibration at speed | Driveshaft and diff support not matched to the new layout. | Use the kit maker's driveshaft (Hinson moved to aluminum only) and a stand-alone diff brace.Medium818 |
Frequently asked
Is there a bolt-in LS swap kit for the RX-8?
Not a fully bolt-in one for every route. LS1RX8.com sells a bolt-on kit that still needs holes drilled, CXRacing sells bolt-on mounts and bracing, Hinson's equipment needs some welding, and V8 Roadsters replaces the front subframe. All of them leave you to solve wiring, the dash and the rear differential.1716110
Does the RX-8 gauge cluster work after an LS swap?
Only with extra work. The cluster expects CAN messages from the Mazda engine computer, so builders either keep that computer running the dash with a crank trigger and Mazda senders on the V8, or fit a CAN module. V8 Roadsters sells a module for 58x GM computers, but lists ABS, traction and cruise as still in progress.Medium141819
Can you keep the RX-8 electric power steering with an LS?
It is difficult. CXRacing calls the factory electric rack hard to make work after the swap, and a builder reports that keeping it means keeping the Mazda engine computer in the car. Many builds instead fit a modified hydraulic MX-5 or RX-7 rack driven by a GM pump.Low16191218
Will the RX-8 rear differential hold an LS?
The weak point is the mounting, not just the gears. LS1RX8.com reports hard launches tearing the diff mounting ears off the subframe, and the Street Machine car broke its upper diff support after a PPF delete. Builders reinforce the mounts, keep the Mazda diff with taller RX-7 gears, or convert to a Ford 8.8 with matched axles.Medium17181322
What transmission do you use for an RX-8 LS swap?
The GM T56 six-speed is the documented choice, and LS1RX8.com calls the 1998-2002 Camaro LS1 and T56 pair its direct-fit drivetrain. Hinson also offers its mounts for the 4L60E automatic. Whatever you choose, it needs a new crossmember because the RX-8's power plant frame is removed.Medium17119
Is an LS-swapped RX-8 street legal?
It depends on where you live; this is general information, not legal advice. In the US, EPA expects the result to match a certified configuration, and California adds a BAR Referee inspection, with no E-ROD shortcut for a 2004-11 car. The UK needs a V5C update, Germany a §19 inspection, and Australia state engineering.Medium303132333435
Related
Sources
35 sources
- LSx V8 Mazda RX8 Mounting Equipment · Hinson Motorsports · vendor-doc · retrieved 2026-10-27
- LS V8 Mazda RX8 Bumpsteer Kit · Hinson Motorsports · vendor-doc · retrieved 2026-10-27
- LS V8 Mazda RX8 Sway Bar Mounts · Hinson Motorsports · vendor-doc · retrieved 2026-10-27
- LS V8 Mazda RX8 Cooling System · Hinson Motorsports · vendor-doc · retrieved 2026-10-27
- LS V8 Mazda RX8 Street Fuel System · Hinson Motorsports · vendor-doc · retrieved 2026-10-27
- LS V8 RX8 1 7/8 in Stainless Steel Headers · Hinson Motorsports · vendor-doc · retrieved 2026-10-27
- LS V8 RX8 3 in Stainless Steel Y-Pipe · Hinson Motorsports · vendor-doc · retrieved 2026-10-27
- LS V8 Mazda RX8 Aluminum Driveshaft · Hinson Motorsports · vendor-doc · retrieved 2026-10-27
- RX8 ABS Brake Module Bracket · Hinson Motorsports · vendor-doc · retrieved 2026-10-27
- RX8 LSx Engine Swap Kit by V8R · V8 Roadsters · vendor-doc · retrieved 2026-10-27
- Mazda RX8 LSx Conversion Package by V8R · V8 Roadsters · vendor-doc · retrieved 2026-10-27
- NC & RX8 Power Steering Conversion · V8 Roadsters · vendor-doc · retrieved 2026-10-27
- RX8 Ford 8.8 Differential Swap · V8 Roadsters · vendor-doc · retrieved 2026-10-27
- CAN Conversion Module for Stock Mazda Gauges · V8 Roadsters · vendor-doc · retrieved 2026-10-27
- Mazda RX8 Parts & Upgrades (catalog page) · V8 Roadsters · vendor-doc · retrieved 2026-10-27
- LS1 Swap Mount Kit Torsion Bar Subframe Bracer Sway Bar for Mazda RX-8 (ESK-RX8-ALL) · CXRacing · vendor-doc · retrieved 2026-10-27
- LS1RX8.com swap kit FAQ and differential notes (home page) · LS1RX8.com · vendor-doc · retrieved 2026-10-27
- 6.0-litre LS-swapped Mazda RX-8 · Street Machine · press · retrieved 2026-10-27
- RX-8 engine swap options? (forum thread, builder post of Oct 2019) · Grassroots Motorsports forum · community · retrieved 2026-10-27
- An LS1 and T-56-Swapped Mazda RX-8 Is Up For Grabs · LSX Magazine · press · retrieved 2026-10-27
- From Tired to Triumph: LS1 Swapped Mazda RX-8 · LSX Magazine · press · retrieved 2026-10-27
- Mazda RX-8 with a LS1 V8 · Engine Swap Depot · community · retrieved 2026-10-27
- Mazda RX-8 · Wikipedia · reference · retrieved 2026-10-27
- Mazda RX-8 production to end in June 2012 (news release, 26 April 2012) · Mazda Motor Corporation · oem · retrieved 2026-10-27
- Is It Worth LS-Swapping A Mazda RX-8? Here's What Owners Say · SlashGear · press · retrieved 2026-10-27
- 350Z LS1 Wiring Harness · Wiring Specialties · vendor-doc · retrieved 2026-10-27
- General Motors LS-based small-block engine · Wikipedia · reference · retrieved 2026-10-27
- Dialing In LS Sensors For Various Generations · EngineLabs · press · retrieved 2026-10-27
- Nissan 240SX LS V8 Engine Swap Guide Part 2: Let's Get Started · Speed Academy · press · retrieved 2026-10-25
- Tampering Policy: The EPA's Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices (Nov 2020) · US Environmental Protection Agency · standard · retrieved 2026-10-25
- Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-25
- Executive Order D-126-32: GM LS3 E-ROD engine kit · California Air Resources Board · standard · retrieved 2026-10-25
- Change vehicle details on a V5C registration certificate (log book) · GOV.UK / DVLA · standard · retrieved 2026-10-27
- StVZO § 19 Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
- VSB 14 National Code of Practice for Light Vehicle Construction and Modification, Section LA: Engines · Queensland Department of Transport and Main Roads · standard · retrieved 2026-10-25

