G35 LS Swap (V35, 2003-2007): Sedan and Coupe Kits, CD009 or T56, Driveshaft, CAN Gauges, Automatics and Legal Guide

A G35 LS swap borrows most hardware from the 350Z, since both share Nissan's FM platform, and Sikky and LOJ sell kits for the G35 sedan and coupe. The G35-specific hurdles are a longer driveshaft, CAN-bus gauges, fans and A/C that rely on engine-computer messages, and the many automatic and AWD G35x cars, for which we found no AWD kit.Medium4571

Difficulty3/5 · ModerateMedium5714
  • Bolt-in mounts, pans, transmission mounts and adapters exist for the G35 sedan and coupe.
  • The gauges, A/C compressor request and fan request all travel over CAN from the Nissan engine computer.
  • The longer wheelbase needs a G35-specific driveshaft, and makers disagree on steel versus aluminum.
  • Most cars are automatics, and AWD G35x sedans add a transfer case and AWD control unit with no kit we could find.

At a glance

The key numbers and parts, with the source on each tile.

Stock engine
  • VQ35DE 3.5 L V6
  • Wikipedia lists about 260 hp for the 2003-04 sedan, 280 hp for the coupe and 2005-06 automatics, and 298 hp for 2005-06 six-speed cars
Sourced · medium4
Model yearsSedan 2003-2006, coupe 2003-2007Sourced · medium4
Platform and wheelbase
  • Nissan FM platform shared with the 350Z
  • 112.2 in (2,850 mm) wheelbase versus the 350Z's 104.3 in2,649 mm
Sourced · medium413
Factory gearboxes
  • 5-speed RE5R05A automatic or 6-speed manual
  • The AWD G35x sedan was automatic only
Sourced · medium4
Curb weight
  • About 3,351-3,395 lb per Wikipedia's text1,520-1,540 kg
  • Its spec table lists heavier figures for some versions
Sourced · medium4
Mount kits
  • Sikky Stage 1 G35 package2- or 4-door, left-hand drive
  • LOJ 350Z/G35 kits
Sourced57
Driveshaft
  • LOJ offers only aluminum or carbon fiber for the G35
  • Sikky's G35 package ships a steel one-piece shaft
Sourced75
Gauges
  • Tach and temperature from the engine computer over CAN
  • Speedometer from the VDC/TCS/ABS unit over CAN
Sourced23
Sedan fuel system
  • Returnless
  • LOJ upgrades the sedan sender with pumps and a regulator set to 58 psi4 bar
Sourced10

Recommended engines

  • LS1 · Gen III drive-by-cable engine; Wiring Specialties' G35 plug-in harness with a CAN controller for the factory gauges supports drive-by-cable engines only.
  • LS3 / L99 · Gen IV 58x drive-by-wire engine; LOJ's CAN translator package for the 350Z and G35 needs a 58x engine and lets the stock Nissan pedal drive the GM throttle.
  • 6.0 LQ4 / LQ9 / LY6 / L96 (truck) · Iron-block truck 6.0 L; Sikky lists the LQ4 among engines that fit its G35 mounts and pan, a lower-cost route if you accept the extra front weight.

Mounts

A G35 LS swap uses the same core hardware as the 350Z, so the 350Z guide covers the shared details.

Sikky Stage 1 G35
  • Billet mounts, transmission mount, rear-sump aluminum pan with remote filter, and a one-piece driveshaft
  • For 2- or 4-door left-hand-drive G35s
Sourced5
LOJ 350Z/G35 Basic

Mounts, rearward transmission mount, 7 qt (6.6 L) pan, shortened linkage, CD00x adapter, flywheel and mini starter

Sourced7
Accessory clearance

Sikky says some A/C compressor and bracket setups hit the right engine mount

Sourced5

Sikky's Stage 1 G35 package fits two- and four-door left-hand-drive cars, and Sikky says it needs no crossmember or subframe changes and no secondary firewall removal.54

LOJ Conversions sells its kits as 350Z/G35 parts. The Basic CD00x kit includes mounts, a transmission mount that moves the gearbox rearward, a 7 qt (6.6 L) baffled pan, shortened shift linkage, adapter plate, flywheel and mini starter.7

Pick the accessory drive with the mounts. Sikky warns some A/C compressor and bracket setups hit its right engine mount, while LOJ's accessory drive kit keeps the stock power steering pump, alternator and optional A/C compressor with factory plumbing and wiring.58

Transmission

Many G35s left the factory as automatics, and the AWD G35x came only with the five-speed automatic.

Factory gearboxes
  • RE5R05A 5-speed automatic or 6-speed manual
  • G35x automatic only
Sourced · medium4
CD00x speed signal
  • The CD009 has no built-in speed sensor for the GM computer
  • LOJ adds an external pickup
Sourced8
GM gearboxes
  • Tunnel modification required
  • Sikky's mount suits T56, T56 Magnum, TR6060 and CD009 with a 1/2 in adapter13 mm
Sourced95

That makes the gearbox the first G35-specific decision: convert to a manual, or fit a GM automatic such as the 4L60E, 4L80E or 6L80.Medium4129

Manual cars can keep the CD00x through an adapter, which avoids tunnel work. LOJ's kits relocate the gearbox rearward with a shortened linkage, and its master kit adds an external speed pickup because the CD009 has no built-in speed sensor for the GM computer.78

A GM T56, TR6060 or 6L80/6L90 needs transmission tunnel modification, per LOJ. Sikky's G35 package is designed around an LS1-style T56 with a relocated shifter that exits the factory hole, and its mount also suits the T56 Magnum, TR6060 and CD009.95

An automatic-to-manual conversion adds clutch pedal and hydraulics work. Wiring Specialties offers G35 harness options both for auto-to-manual conversions and for GM automatics in automatic chassis, and Sikky sells a G35 clutch line kit.Medium126

Clearance

Use the pan made for your mounts.

Sikky pan
  • Rear-sump aluminum pan, 6 in deep sump, 8 qt, side-port remote filter152 mm · 7.6 L
  • Does not hang below the crossmember
Sourced5
LOJ pan7 qt with road-race baffling, dipstick and pickup6.6 LSourced7

Sikky's rear-sump pan is shaped around the 350Z/G35 front subframe, holds 8 qt (7.6 L) and is meant to be used with Sikky mounts, while LOJ's 7 qt (6.6 L) pan pairs with its own kit.57

Keeping the CD00x avoids tunnel work, while any GM gearbox needs the tunnel modified to clear the bellhousing and case. Mock up the engine and gearbox before final fastening, and check the shifter through every gate.79

Check the steering rack hard lines against the driver-side header at mock-up. LOJ warns that the 2006 350Z rack's lines hit one primary on its headers; we found no equivalent note for the G35, so verify on your car.Medium8

Cooling

LOJ sells a G35 street radiator that drops into the stock radiator support and keeps the A/C condenser mounting.

LOJ G35 street radiator

C&R-built aluminum radiator that drops into the stock G35 radiator support and carries the factory A/C condenser

Sourced11
Fan and A/C requests

In the stock car the engine computer sends cooling fan and A/C compressor requests to the IPDM E/R over CAN

Sourced1

LOJ says it suits spirited street, drag and autocross use, and recommends a race radiator without A/C for extended hot-weather track work.11

In the stock car, the engine computer asks the IPDM E/R (the engine-room power module) to run the fans and the A/C compressor over CAN. With the Nissan computer gone, something must send those requests, or the fans and compressor must be wired another way.1

Wiring Specialties' G35 harness keeps the factory fans with preset on and off temperatures, while LOJ's CAN translator keeps climate control and A/C working with its accessory drive. Plumb the LS steam port to a high point and bleed the system.Medium12817

Fuel

The G35 sedan keeps its returnless system.

Sedan fuel upgrade

LOJ send-in service: in-tank pumps, regulator preset to 58 psi (4 bar), quick-disconnect line to the LS rail

Sourced10
Why send-in

LOJ says new G35 sedan sending units are not sold in the aftermarket

Sourced10

LOJ upgrades the stock sedan sending unit with higher-flow pumps and a regulator preset to 58 psi (4 bar) to match LS calibrations, as a send-in service because new sedan senders are not sold aftermarket.10

Confirm the sending unit for your body before ordering, since LOJ lists the sedan package separately from the 350Z fuel system in its kits. LOJ says higher-output builds need a complete fuel system; check flow with the fuel pump calculator.Medium108

Exhaust

Sikky route
  • Factory LS3-style manifolds fit the Sikky package with Sikky test and mid pipes
  • Sikky also sells G35 swap headers
Sourced56
LOJ headers

Stainless headers with 1-7/8 in (48 mm) primaries and 3 in (76 mm) collectors in its master kits

Sourced8

Sikky says factory LS3-style exhaust manifolds fit its G35 package when used with its test and mid pipes, which is the simpler route. It also sells G35-specific long-tube headers.56

LOJ's master kits include stainless headers with 1-7/8 in (48 mm) primaries, 3 in (76 mm) merge collectors and oxygen sensor bungs. Keep catalysts where your jurisdiction requires them.8

Electrical

ECU+ PDM / relaysCrank / cam sensorsThrottle (DBW) + pedalInjectorsCoilsEngine sensorsFuel pumpCooling fansGauges / tachStarter / chargingChassis loads

The G35 is a CAN-bus car.

CAN network

ECM, combination meter, BCM, steering angle sensor, VDC/TCS/ABS unit and IPDM E/R, plus TCM on automatics and an AWD control unit on AWD cars

Sourced1
Gauges
  • Tach and coolant temperature from the ECM over CAN
  • Speedometer from the VDC/TCS/ABS unit over CAN
  • Fuel gauge hard-wired
Sourced23
Stability control

Wiring Specialties lists traction and stability control as not functional with its plug-in harness

Sourced12

Nissan's manuals for the 2003 and 2004.5 sedan show the engine computer sending engine speed and coolant temperature to the meter over CAN, and the VDC/TCS/ABS unit sending road speed. Without a translator, the tach and temperature gauge go dead.231

The network carries more than gauges. The engine computer also sends engine speed and accelerator position to the VDC/TCS/ABS unit, requests the A/C compressor and fans from the IPDM E/R, and lights the check-engine lamp, so plan each function separately.1

Wiring Specialties' G35 LS1 harness uses a CAN controller for tach, temperature, check-engine lamp, speedometer, fuel gauge and illumination, and needs the body harness, BCM and fuse boxes unmodified. LOJ's Gen IV package uses a translator so the stock Nissan pedal drives the GM throttle.128

Expect stability control to be lost on the plug-in route; Wiring Specialties lists it as not functional, although its marketing copy elsewhere claims no fault lights. LOJ says factory ABS keeps working. AWD cars add an AWD control unit to the network, and we found no kit addressing it.Medium1281

Chassis

The G35's 112.2 in (2,850 mm) wheelbase is about 8 in (200 mm) longer than the 350Z's, so the driveshaft does not carry over.

Wheelbase112.2 in, about 8 in longer than the 350Z2,850 mm · 200 mmSourced · medium413
Driveshaft
  • LOJ: no steel shaft for the G35 because of length and critical speed
  • Sikky: steel one-piece shaft with 1310 U-joints, aluminum optional
Sourced75
Rear differential

Forum reports place the G35 unit in the same R200 family as the 350Z

Low confidence14

LOJ will not sell a steel shaft for the G35 because of its length and critical speed, while Sikky's G35 package ships a steel shaft; ask each maker how it was rated.Medium41375

Owners report the rear differential belongs to the same R200 family as the 350Z, so the 350Z guide's notes on limited-slip upgrades, splines and axle lengths apply. Sikky sells solid differential bushings and adjustable rear subframe bushings for the G35.Low146

AWD G35x sedans add a transfer case, front differential and AWD control unit. We found no LS kit for them, so treat a G35x as a custom fabrication project rather than a kit swap.Medium41

Tuning

With a donor GM computer, the minimum is a startup calibration that disables GM anti-theft.

GM rating (reference)GM rated the LS1 at 345-350 hpSourced · medium15
Anti-theft
  • The GM VATS must be disabled
  • Wiring Specialties' startup tune removes VATS, EVAP, rear O2 and purge functions
Sourced12

Wiring Specialties' standard startup tune removes VATS, evaporative purge and rear oxygen sensor functions, but it does not change fuel maps, so plan a full calibration after.12

Gen IV engines with Active Fuel Management need it disabled in calibration or hardware. LOJ's Gen IV package works with GM's E38 computer and keeps OBD2 access for logging and emissions testing.Medium158

Log with a wideband oxygen sensor before loaded pulls, confirm knock control is active, and set a conservative rev limiter. Change ignition timing in small steps with knock monitoring, never copied from another car.Medium16

Parts checklist

Tick what you have; the list is saved in this browser.

0 of 21 ticked (saved in this browser)
Mounts
Transmission
Clearance
Cooling
Fuel
Exhaust
Electrical
Chassis
Tuning
Legal

Order of work

10 stages, in the order most builds follow.

  1. Check the law and the body
    Confirm local rules, then confirm sedan or coupe, model year, and whether the car is RWD; AWD G35x cars have no kit route.
  2. Choose gearbox and electronics together
    Decide between the CD00x, a T56 or a GM automatic, and pick a harness with CAN support for your engine generation.
  3. Remove the VQ35 and gearbox
    Support the car on stands, drop the engine and transmission, and leave the body harness, BCM and fuse boxes unmodified.
  4. Fit mounts, pan and adapter
    Install the swap pan, remote filter and, for the CD00x, the adapter, flywheel and clutch before lifting the engine in.
  5. Install engine and gearbox
    Set the engine on its mounts, fit the transmission mount, modify the tunnel if using a GM gearbox, and fit the shifter.
  6. Fit driveshaft and accessories
    Install a G35-length driveshaft and the accessory drive, checking A/C bracket clearance at the right mount.
  7. Fit cooling, fuel and exhaust
    Install the radiator and fans, upgrade the fuel sender, and fit manifolds or headers clear of the rack lines.
  8. Wire engine and CAN translator
    Install the harness and translator, fit the oil pressure sender adapter and speed pickup, and fuse every new feed.
  9. Start, bleed and calibrate
    Load a startup calibration, bleed cooling and clutch, verify every gauge, fan and the A/C, and log with a wideband.
  10. Road test and certify
    Check for driveline vibration and warning lamps, then complete the inspection your jurisdiction requires.

Common problems

Symptom, cause and the usual fix.

ProblemCauseFix
Tach and temperature gauge dead after the swapThe meter reads both from the Nissan engine computer over CAN.Fit a harness with a CAN controller or translator that sends those messages.212
A/C compressor will not engage or fans do not runThe Nissan engine computer requested both from the IPDM E/R over CAN, and nothing replaces those requests.Use a translator or harness that supports A/C and fans, or wire them through relays.1128
Driveline vibration at speedA driveshaft not rated for the G35's longer length and critical speed.Use a shaft the maker specifies for the G35; LOJ offers only aluminum or carbon fiber for it.74
A/C compressor bracket hits the right engine mountSome compressor and bracket combinations do not clear Sikky's mount.Modify the bracket or change accessories, or use an accessory drive designed for the kit.58
GM computer sees no vehicle speed with the CD009The CD009 has no built-in speed sensor for the GM computer.Add an external speed pickup, as LOJ's master kit does.8
Traction or stability warning after the swapThe VDC/TCS/ABS unit no longer receives engine data it expects.Accept stability control loss on plug-in routes, or choose a translator that covers it, and confirm ABS still works.Medium121

Frequently asked

Do 350Z LS swap kits fit the G35?

Mostly, yes. LOJ sells its mounts, pans and adapters as 350Z/G35 parts, and Sikky makes a G35 package for two- and four-door cars. The driveshaft is the main exception, because the G35 wheelbase is about 8 in (200 mm) longer, and the G35 sedan has its own fuel sending unit.7541310

Can you LS swap a G35 sedan?

Yes. Sikky's G35 package is developed for two- or four-door left-hand-drive cars, Wiring Specialties offers its G35 harness for the coupe and sedan, and LOJ sells a sedan-specific fuel sender upgrade. Most sedans are automatics, so plan the gearbox early: convert to a manual or fit a GM automatic.512104

Can you LS swap an AWD G35x?

Not with a kit we could find. The G35x adds a transfer case, front differential and an AWD control unit on the CAN network, and it came only with the automatic. Expect a custom fabrication project covering mounts, transfer case adaptation and the AWD electronics, with no documented recipe.Medium41

Does the G35 gauge cluster work after an LS swap?

Only with a CAN interface. Nissan's manuals show the tach and coolant gauge fed by the engine computer over CAN and the speedometer by the VDC/TCS/ABS unit. Plug-in harnesses with a CAN controller restore tach, temperature, check-engine lamp, speedometer and fuel gauge, but stability control is usually lost.212

Can you keep the automatic in a G35 LS swap?

You can keep an automatic, but we found no kit that keeps the Nissan five-speed with an LS. Documented routes use a GM 4L60E, 4L80E or 6L80/6L90 with its own controls; Wiring Specialties offers harness options for GM automatics in automatic G35s, and LOJ sells a 6L80/6L90 kit that needs tunnel work.Medium129

Is an LS-swapped G35 smog legal?

It is difficult, and this is general information, not legal advice. EPA expects the result to match a certified configuration, California requires a BAR Referee inspection, and the GM E-ROD order covers only 1995 and older vehicles. The UK needs a V5C update, Germany a §19 inspection, and Australia state engineering.Medium181920212223

Related

Sources

23 sources
  1. 2004.5 G35 Sedan Service Manual, section LAN (CAN Communication, LAN-5 to LAN-7) · Nissan Motor Co. · service-manual · retrieved 2026-10-27
  2. 2004.5 G35 Sedan Service Manual, section DI (Combination Meters, DI-4 to DI-5) · Nissan Motor Co. · service-manual · retrieved 2026-10-27
  3. 2003 G35 Sedan Service Manual, section DI (Combination Meters system description) · Nissan Motor Co. · service-manual · retrieved 2026-10-27
  4. Infiniti G · Wikipedia · reference · retrieved 2026-10-27
  5. Sikky Stage 1 Infiniti G35 LS Package · Sikky Manufacturing · vendor-doc · retrieved 2026-10-27
  6. Sikky product search results for G35 (catalog listing) · Sikky Manufacturing · vendor-doc · retrieved 2026-10-27
  7. 350Z / G35 LSx BASIC Swap Kit - Z33 Transmission · LOJ Conversions · vendor-doc · retrieved 2026-10-27
  8. 350Z / G35 LSx MASTER Swap Kit - Z33 Transmission · LOJ Conversions · vendor-doc · retrieved 2026-10-27
  9. 350Z / G35 LSx MASTER Swap Kit - 6L80 / 6L90 Transmission · LOJ Conversions · vendor-doc · retrieved 2026-10-27
  10. G35 Sedan LS Swap Fuel System · LOJ Conversions · vendor-doc · retrieved 2026-10-27
  11. G35 LSx Swap Street Radiator · LOJ Conversions · vendor-doc · retrieved 2026-10-27
  12. LS1/Vortec Wiring Harness for G35 (CANBUS PRO Series) · Wiring Specialties · vendor-doc · retrieved 2026-10-27
  13. Nissan 350Z · Wikipedia · reference · retrieved 2026-10-27
  14. Rear diff questions (forum thread) · My350Z.com · community · retrieved 2026-10-27
  15. General Motors LS-based small-block engine · Wikipedia · reference · retrieved 2026-10-27
  16. Dialing In LS Sensors For Various Generations · EngineLabs · press · retrieved 2026-10-27
  17. Nissan 240SX LS V8 Engine Swap Guide Part 2: Let's Get Started · Speed Academy · press · retrieved 2026-10-25
  18. Tampering Policy: The EPA's Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices (Nov 2020) · US Environmental Protection Agency · standard · retrieved 2026-10-25
  19. Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-25
  20. Executive Order D-126-32: GM LS3 E-ROD engine kit · California Air Resources Board · standard · retrieved 2026-10-25
  21. Change vehicle details on a V5C registration certificate (log book) · GOV.UK / DVLA · standard · retrieved 2026-10-27
  22. StVZO § 19 Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
  23. VSB 14 National Code of Practice for Light Vehicle Construction and Modification, Section LA: Engines · Queensland Department of Transport and Main Roads · standard · retrieved 2026-10-25