Race car PDM guide: PDM basics and electrical load planning

A race car PDM (power distribution module) replaces the fuse and relay box with solid-state switches that measure each channel's current and turn it off on overload, then retry or latch off by rule. Plan it in four steps: list every load with running and inrush current, assign channels with margin, size each wire and trip, then check the total against the main feed, battery and alternator. Set fuel pump and fan safe states before first power-up.711811

Key takeaways

  • A PDM channel is a smart high-side switch with current sensing: it can soft-start, PWM, shed load and log faults, which fuses and relays cannot.
  • Plan from the load list, not the channel list. Record running current, inrush and whether the load runs continuously, intermittently or briefly.
  • Inrush matters: pumps, fans and lamps draw several times their running current at switch-on. Channel trip settings must ride through it.
  • Wire is still sized for current, run length and heat. A PDM protects the wire only if its trip current is set at or below the wire's safe rating.
  • Add up what can run at the same time, then check the main feed cable, battery and alternator against that number, plus key-off drain.
  • Decide safe states: fuel pump stops on stall or crash, fans fail on, critical loads have a fallback when CAN drops.

What a PDM does

A race car PDM takes one large battery feed and splits it into many switched, protected outputs.

Switch typeSmart high-side MOSFET with current sense and thermal protectionSourced89
Fault behaviour
  • Trip, then retry a set number of times or latch off
  • Fault logged
Sourced17
ControlSwitch inputs, analog sensors, CAN messages, built-in logicSourced110

Each output is a semiconductor switch with built-in current sensing, so the module knows exactly what every load draws.71

On overload the channel switches off in microseconds to milliseconds, like an electronic fuse. The PDM can then retry a set number of times or stay off, and it reports the fault instead of leaving you to find a blown fuse.81

Inputs and logic let it act on switches, sensors or CAN messages: fans by coolant temperature, a pump by engine state, a brake light from a pressure switch. That logic replaces a box of relays and their wiring.110

PDM vs relays and fuses: the trade-offs

Relays and fuses are cheap, simple and easy to source at any parts store.

Relays + fuses
  • Low cost, simple
  • No diagnostics, many joints, manual reset
Sourced · medium1819
PDM
  • Per-channel current sense, trip/retry, PWM, logic, logging
  • Higher cost, needs setup
Sourced · medium71

Their weaknesses are weight, many joints that can fail, no diagnostics, and a blown fuse that stays blown until someone replaces it.Medium1819

A PDM costs more and needs configuring, but gives current monitoring per channel, programmable trip and retry, soft-start and PWM for pumps and fans, and logs. For a car with many loads, it also removes most of the relay wiring.Medium71

Step 1: list every load and its current

Write down every electrical load

Fuel pumps, fans, ignition and injector feeds, ECU, dash, water pump, lights, wipers, starter solenoid, data system. For each, record running current, inrush current and how long it runs.Medium171

Take currents from the component's datasheet or measure them with a clamp meter at operating voltage and temperature. Guessing from the fuse fitted by a previous owner tends to hide problems rather than size for them.Medium178

Motors and lamps draw far more than their running current at switch-on, and a fuel pump draws more as fuel pressure rises. Note both numbers, because the channel has to tolerate the inrush and protect the wire at running current.Medium722

Load list template

Illustration in production.

Step 2: match loads to channels

Give each load a channel whose continuous rating exceeds its running current with clear margin.

Fuse makers publish derating for continuous current and ambient temperature, and a sealed module in a hot car needs that margin too; follow your PDM maker's channel derating.Medium118

Large loads can share two channels switched together, as long as the PDM supports paired channels with synchronised switching and group trip. Keep each wire and each connector pin within its own rating.Medium112

Use PWM-capable channels for fans and pumps whose speed you want to control. Small reversible motors such as flaps or window motors need a half-bridge pair, not a single high-side switch.23241

Step 3: size the wire and set the trip

Size each wire for its current, run length and temperature, then set the channel trip at or below what that wire can carry safely.

Worked example (computed)20 A, 4 m, 3% drop, 60 °C → 10 AWG (2.25% drop) or 4 mm²2.96%Sourced5
Trip vs wireChannel trip ≤ the wire's safe current at its temperatureSourced1820

The trip protects the wire; if the trip is higher than the wire's rating, the wire is the fuse.182011

Check voltage drop on long or critical runs. Example: a 20 A fuel pump on a 4 m (13 ft) run with a local chassis ground, at a 3% drop limit and 140 °F (60 °C) wire, needs 10 AWG or 4 mm² (computed with the wire gauge calculator).521

In the engine bay, use 125 °C (257 °F) cross-linked wire such as SAE J1128 TXL. A pump that sees low voltage flows less fuel, so do not accept a large drop on the pump circuit.146

Wire gauge for a PDM channel
A
V
%
°F

Hot engine bays raise copper resistance about 0.4% per °C.

Result

Smallest AWG: 10 AWG2.25 %voltage drop
Smallest metric: 4 mm²2.96 %voltage drop

Voltage drop is one check. The wire must also be rated for the current at its temperature and bundling, and the fuse must protect the wire.

Planning estimate from the formula below, not a measurement.

Open the automotive wire gauge calculator →

Step 4: total current, main feed, battery and alternator

Add up the loads that can run at the same time, not every load in the car.

A typical worst case is a hot idle in the pits: fans flat out, pumps on, lights and data running, and the alternator at low speed.Medium17

Size the PDM's main feed cable and its fuse or breaker for that total, keep the feed short, and protect it close to the battery. Check the alternator's output at idle speed covers the running total, or the battery will drain during a session.Medium1718

Check key-off drain too. A module powered straight from the battery must sleep at very low current, or a week parked flattens the battery.Medium116

Step 5: logic, safe states and failure behaviour

Decide what each output does when something fails.

Fuel pumpPrime at key-on, run with engine, stop on stall or crashSourced13
Cooling fansFail onSourced1
CAN-controlled outputsDefined fallback on message lossSourced1

The fuel pump should prime briefly at key-on, then run only while the engine turns, and stop on a stall or crash signal. Cooling fans should fail on, not off.13

If an output follows a CAN message, define what happens when that message stops arriving. Critical loads need a hard-wired or default fallback, not a silent switch-off.115

Set retry counts per load. A fan that stalls on debris can retry; a channel that trips on a short circuit should latch off and show a fault, not hammer the short.Medium71

Working with the ECU and dash over CAN

A PDM and ECU on the same CAN bus can share signals: the PDM reads rpm and coolant temperature to run fans, the ECU sees PDM fault states. The bus needs a 120 Ω terminator at each end and a planned ID list.1513

Keep engine-safety functions where they belong. Throttle sensors stay on the ECU's own inputs, and the ECU keeps control of injection and ignition; the PDM switches power, it does not decide fuelling.325

Reading another maker's ECU broadcast in listen-only mode is low risk when the maker documents the stream. Writing to that ECU is a different matter and needs the maker's authorization.41

PDM planning checklist

1.

Load list with running and inrush current. 2. Channel per load with margin; paired channels only where supported.

3. Wire size per channel by current, length and heat. 4.

Trip setting at or below the wire's rating.Medium111

5. Total simultaneous current vs main feed, battery and alternator at idle. 6.

Key-off drain. 7. Safe state per output and CAN-loss fallback.

8. Label every output wire and save the configuration with the car's documents.Medium117

Do it with GAINS (separate product module)

GAINS: the PDM2 is a compact PDM in design with 13 current-sensed outputs (2 × about 16 A, 9 × 8 A, 2 half-bridges, 1 flex), 8 analog or switch inputs, 2 speed inputs, CAN, GNSS and an app for setup that never sits in a control loop. Status: roadmap, pre-release.1

The PDM2 is a concept for high-content builds such as restomods: eight 25 A half-bridge channels on two DTP connectors plus a battery-post feed, aimed at windows, locks, fans and electric A/C. Its current ratings are targets pending a schematic and testing.2

Frequently asked

What is a PDM in a race car?

A power distribution module replaces the fuse and relay box. It switches each load with a solid-state switch that measures current, trips on overload, retries or latches off by rule, and logs faults. It can also run logic, such as fans by coolant temperature or a fuel pump by engine state.71

Do I need a PDM?

Not always. A simple car with a few loads runs fine on good relays and fuses. A PDM earns its cost when you have many loads, want diagnostics and logging, need PWM control of pumps and fans, or want to remove relay wiring and fuse failures that strand the car mid-session.Medium181

How do I size PDM channels?

Start from each load's running and inrush current. Choose a channel whose continuous rating exceeds the running current with margin, check it tolerates the inrush, size the wire for the current, run length and heat, and set the trip at or below the wire's safe rating so the channel protects the wire.Medium1120

Does a PDM replace fuses completely?

It replaces the per-load fuses and relays. You still need protection on the main feed from the battery to the PDM, sized for that cable and fitted close to the battery, because the PDM cannot protect the cable that feeds it.1817

What happens if the PDM loses CAN communication?

That depends on how it is configured, which is why you should decide it in advance. Outputs that follow CAN messages need a defined fallback when messages stop. Cooling fans should fail on, and the fuel pump should follow a hard-wired engine-running or ignition signal rather than switch off silently.Medium115

Related

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

25 sources
  1. internal GAINS internal: PDM2 v0 design spec (hardware/mini-pdm/SPEC.md): outputs, inputs, safe defaults
  2. internal GAINS internal: PDM2 v0 concept (hardware/mini-max-pdm/CONCEPT.md)
  3. internal GAINS internal: ECU2 v0 concept (hardware/mini-ecu/CONCEPT.md): fuel pump and DBW rules
  4. internal GAINS internal: Third-party ECU integration evidence (docs/research/THIRD_PARTY_ECU_EVIDENCE.md)
  5. internal GAINS internal: Automotive wire gauge calculator (@aitune/calc wire-gauge), voltage-drop method per ASTM B258 areas
  6. internal GAINS internal: Fuel pump size calculator (@aitune/calc fuel-pump-flow), assumptions
  7. Smart power switches (high-side and low-side) product family overview · Infineon Technologies · vendor-doc · retrieved 2026-10-27
  8. High-side switches product family · Infineon Technologies · vendor-doc · retrieved 2026-10-27
  9. TPS1H100-Q1 40-V, 100-mOhm single-channel smart high-side power switch data sheet · Texas Instruments · vendor-doc · retrieved 2026-10-27
  10. PowerBox PBX 190 data sheet 75077387 · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  11. Fuseology Design Guide · Littelfuse · vendor-doc · retrieved 2026-10-27
  12. Superseal 1.0 34-position plug datasheets (4-1437290-0 / -1) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  13. Controller Area Network physical layer requirements (SLLA270) · Texas Instruments · vendor-doc · retrieved 2026-10-27
  14. SAE J1128: Low Voltage Primary Cable · SAE International · standard · retrieved 2026-10-27
  15. ISO 11898-1:2024 Road vehicles, Controller area network (CAN), Part 1 · International Organization for Standardization · standard · retrieved 2026-10-27
  16. ISO 16750-2:2023 Road vehicles, Environmental conditions and testing for electrical and electronic equipment, Part 2: Electrical loads · International Organization for Standardization · standard · retrieved 2026-10-27
  17. Automotive Handbook, 10th ed. (vehicle electrical systems, charging) · Robert Bosch GmbH / Wiley, 2018 · book · retrieved 2026-10-27
  18. Fuse (electrical) · Wikipedia · reference · retrieved 2026-10-27
  19. Solid-state relay · Wikipedia · reference · retrieved 2026-10-25
  20. Ampacity · Wikipedia · reference · retrieved 2026-10-27
  21. Voltage drop · Wikipedia · reference · retrieved 2026-10-27
  22. Inductor · Wikipedia · reference · retrieved 2026-10-27
  23. Pulse-width modulation · Wikipedia · reference · retrieved 2026-10-27
  24. H-bridge · Wikipedia · reference · retrieved 2026-10-27
  25. Electronic throttle control · Wikipedia · reference · retrieved 2026-10-27