Load dump

load dump transientalternator load dumpISO 16750-2 test Apulse 5apulse 5b

A load dump is the high-energy voltage surge produced when a charging alternator suddenly loses its load, most often because the battery is disconnected while the engine runs. The alternator's field cannot collapse instantly, so system voltage can spike far above normal for hundreds of milliseconds and damage unprotected electronics.123

How it works

An alternator regulates its output by controlling field current, and the field winding is a large inductance.

When a big load such as the battery disappears, output current has nowhere to go and the regulator cannot reduce the stored field energy quickly. The voltage rises until the field decays, which takes a long time compared with most electrical transients.13

ISO 16750-2 defines the load dump test for 12 V and 24 V equipment. Test A represents an alternator without central suppression and Test B one with clamping in the alternator. These pulses were previously known as pulses 5a and 5b in ISO 7637-2, and that older naming is still common on datasheets.Medium21

For 12 V systems the unsuppressed Test A pulse is commonly quoted in the range of roughly 79 to 101 V, lasting tens to hundreds of milliseconds, with a source resistance of about 0.5 to 4 Ω. Exact values depend on the test level chosen, so check the edition of the standard your component is rated to.Medium21

Because the pulse is long and the source resistance is low, the energy is large. Small signal protection parts cannot absorb it. Designs use large transient-voltage-suppression (TVS) diodes, series blocking or surge-stopper circuits, or components rated to survive the full voltage.Medium452

In tuning

Never disconnect the battery or open a main isolator with the engine running and the alternator charging.

On race cars, the master switch is normally wired to kill the engine and to route alternator output through a suppression path when it opens, for this reason.Medium13

When fitting aftermarket controllers, data loggers or power modules, check their stated transient ratings rather than assuming automotive tolerance. A TVS diode that is overstressed usually fails short, so the circuit feeding it must be fused; otherwise the shorted part can overheat the wiring.52

Myths vs facts

Myth A load dump only happens if a battery cable is pulled off on purpose.

Fact Any sudden loss of a large charging load can cause one: a corroded or loose battery terminal, a failing master switch, or a fuse opening in the main charge path while the alternator is delivering high current.Medium13

Myth A TVS diode on the supply input makes a module immune to load dump.

Fact Only if it is sized for the pulse energy. An undersized TVS diode is usually destroyed and fails short, which then blows the feed fuse or overheats unfused wiring.54

Frequently asked

What causes an alternator load dump?

A load dump happens when the alternator is charging and its load is removed suddenly, usually by the battery being disconnected. The alternator field stores energy that cannot vanish instantly, so output voltage surges until the field decays. Loose battery terminals and master switches opened with the engine running are common real-world causes.Medium13

How high can load dump voltage get on a 12 V car?

Without central suppression it can reach well above 70 V. The unsuppressed ISO 16750-2 test pulse for 12 V systems is commonly quoted at roughly 79 to 101 V, lasting tens to hundreds of milliseconds. Alternators with built-in clamping limit it much lower, which is what the suppressed Test B represents.Medium21

What is the difference between load dump Test A and Test B?

Test A models an alternator with no central suppression, so the full surge reaches the equipment. Test B models an alternator with internal clamping, so the voltage is capped at a lower level for the same event. Both come from ISO 16750-2 and replaced the older ISO 7637-2 pulses 5a and 5b.Medium21

How do you protect electronics from load dump?

Use parts rated for the pulse, a large TVS diode sized for its energy, or an active surge-stopper or ideal-diode controller that disconnects or limits the supply. Fuse the feed so a failed-short suppressor cannot overheat wiring. At system level, never open the battery circuit while the alternator is charging.Medium562

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Load dump · Wikipedia · reference · retrieved 2026-10-27
  2. ISO 16750-2:2023 Road vehicles, Environmental conditions and testing for electrical and electronic equipment, Part 2: Electrical loads · International Organization for Standardization · standard · retrieved 2026-10-27
  3. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  4. Transient-voltage-suppression diode · Wikipedia · reference · retrieved 2026-10-27
  5. Failure modes and fusing of TVS devices (application note 88440) · Vishay General Semiconductor · vendor-doc · retrieved 2026-10-27
  6. Basics of ideal diodes (SLVAE57) · Texas Instruments · vendor-doc · retrieved 2026-10-27