Reverse polarity protection

reverse battery protectionreverse voltage protectionreverse polarity diodeideal diode protection

Reverse polarity protection is circuitry that prevents damage when a supply is connected backwards, such as a battery or jump leads reversed. It blocks or diverts the reverse current that would otherwise flow through semiconductor body diodes, using a series diode, a MOSFET arranged as an ideal diode, or a fuse-and-clamp arrangement.543

How it works

Reverse battery connection is common in automotive service.

Texas Instruments notes it occurs during battery maintenance and jump starts, and its automotive examples test protection at -14 V input. Without protection, current flows backwards through the internal body diodes of MOSFET switches and through regulator structures, overheating them.35

The simplest protection is a series diode. It blocks reverse current, but its forward voltage drop wastes power and lowers the supply to the load. A Schottky diode drops less than a standard silicon diode but costs more, and at high current either type needs heat sinking.46

A MOSFET in the supply or ground path gives a much lower drop, set by its on-resistance times load current. Ideal diode controllers drive an N-channel MOSFET so it conducts in the forward direction and turns off on reverse voltage, replacing a diode's losses with a small resistive drop.463

Smart high-side switches often need their own arrangement. TI describes a diode-and-resistor network in the switch's ground pin that protects the control circuitry, while noting that this network does not stop reverse current through the main switching transistor.5

Typical values

Automotive reverse battery test voltage-14VUsed in TI's high-side controller test examplesSourced3
Cold-crank battery voltageAs low as 3-4 VTI ideal diode note; a series diode's drop eats into this headroomSourced6
Silicon diode forward dropAbout 0.6-0.7 VTI example uses 0.6 V; TPS1H100-Q1 body diode 0.7 VSourced48
Schottky diode loss at 10 AAbout 5 W with a 0.5 V dropP = V_F × ISourced · medium4
MOSFET loss at 10 A, 5 mΩ0.5 W and a 0.05 V dropP = I² × R_DS(on)Sourced6
Smart switch reverse rating
  • -18 V max
  • 4 A reverse for under 60 s with GND network
TI TPS1H100-Q1Sourced8

How an ECU uses it

Control modules usually protect their own supply input with a series MOSFET or an ideal diode controller.

TI's power distribution example puts many high-side outputs behind one ideal-diode stage, so the switches downstream never see reverse voltage.3

High-side outputs are the weak spot. With polarity reversed, current can flow back through each output switch and its ground pin. TI's mitigations are a diode-resistor network in the switch ground, current-limit resistors on microcontroller pins and a blocking diode on the supply.5

Some loads, such as heaters, have no protection of their own. TI describes turning the high-side MOSFET fully on during reverse battery so reverse current flows through the low-resistance channel rather than the body diode, limiting heat in the switch.3

How to test it

5 checks, in order.

  1. Before first power-up of a new harness, leave the module unplugged, connect the battery and measure from the connector's supply pins to its ground pins. The meter should read positive battery voltage; a negative reading means crossed feeds.Medium51
  2. If a reversal has happened, disconnect the battery at once and check every fuse, fusible link and the main feed fuse. Blown fuses show where reverse current flowed.Medium57
  3. Check the charging system next. Alternator rectifier diodes conduct heavily on a reversed battery, and damage shows as low charging voltage or ripple on the battery voltage.Low1
  4. Power suspect modules one at a time from a current-limited bench supply at correct polarity and watch the current. A module drawing far more than its normal idle current has likely been damaged inside.Medium56
  5. Safety
    a reversed battery can drive large currents through any unprotected path, heat cables quickly and damage the battery. Disconnect it first, wear eye protection, and do not reconnect until the cause is found.Medium67

Symptoms and causes

Main fuse or fusible link blown after a battery change

Likely causes Battery or jump leads connected backwards

Check Inspect terminals and cable routing, then check other fuses and modules before reconnecting.

Medium57

Module dead after a jump start

Likely causes Reverse current through its input, ESD structures or outputs

Check Bench-power it at correct polarity through a current limit and compare with normal draw.

Medium65

Charging warning or low charging voltage after a reversal

Likely causes Alternator rectifier diodes damaged

Check Measure charging voltage and AC ripple at the battery.

Low1

One high-side output stuck or dead after a reversal

Likely causes Output switch or its ground pin overstressed by reverse current

Check Test the output into a known load and compare with the other channels.

Medium5

In tuning

Before powering a new harness, check polarity at the controller connector with a meter, not just at the battery.

A reversed feed from a mislabeled terminal can damage modules even if the battery itself is connected correctly.Medium51

Protection inside a module does not protect its outputs' loads. Fuel pumps, solenoids and sensors on the same supply can still see reversed voltage. Fusing close to the battery limits the damage if a reversal happens.Medium57

Formula and worked example

P_loss = V_F × I (diode)   |   P_loss = I² × R_DS(on) (MOSFET)
P_loss
power dissipated in the protection deviceW
V_F
diode forward voltageV
I
load currentA
R_DS(on)
MOSFET on-resistanceΩ
46

Common mistakes

Mistake Relying on the ECU's input protection to protect everything.

Do instead It covers the module input. Loads and other modules still need fusing near the battery.Medium57

Mistake Putting a large silicon diode in a high-current feed.

Do instead At 20 A a 0.7 V drop wastes 14 W. Use a MOSFET with an ideal diode controller.Medium46

Mistake Checking polarity only at the battery.

Do instead Verify at the module connector too; mislabeled terminals and harness errors reverse feeds downstream.Medium5

Myths vs facts

Myth If a device has reverse polarity protection, nothing connected to it can be damaged.

Fact The protection covers that device's input. Other loads on the same feed, and sometimes the device's own outputs, can still conduct reverse current. TI notes that some protection networks protect the control circuitry but not the main switching transistor.5

Myth A series diode is always good enough.

Fact It works, but its forward drop costs voltage and heat at high current. For high-current feeds, MOSFET-based ideal diode circuits are used because their loss is much lower.46

Frequently asked

What is reverse polarity protection?

Reverse polarity protection is a circuit that stops current flowing the wrong way when a supply is connected backwards. Common forms are a series diode, a MOSFET driven as an ideal diode, or a fuse with a clamp diode. It protects the device's own input, not every load on the same feed.46

What happens if you connect a car battery backwards?

Current flows backwards through any path it can find, especially the internal body diodes of MOSFETs and regulators. Fuses may blow, and unprotected modules, alternator diodes or sensors can be damaged. TI identifies battery maintenance and jump starting as typical times this happens. Disconnect immediately and check fuses and modules before trying again.Medium35

How does a MOSFET provide reverse polarity protection?

A MOSFET placed in the supply or ground path conducts when polarity is correct and blocks when it is reversed. Driven by an ideal diode controller, an N-channel MOSFET behaves like a diode with a very small drop equal to load current times its on-resistance, so it wastes far less power than a real diode.64

Is a diode enough for reverse polarity protection?

For low-current circuits, yes. A series diode blocks reverse current simply and reliably. At higher currents its forward drop wastes power and reduces supply voltage, so a Schottky diode or a MOSFET ideal diode is preferred. Also check that the diode's voltage rating covers transients on the supply.46

Do ECUs have reverse polarity protection?

Most automotive control units are designed to survive a reverse battery test, because standards such as ISO 16750-2 include one. Protection levels vary by product, and loads driven by the unit may not be protected. Check the specific datasheet rather than assuming, and never rely on it as a substitute for checking wiring.Medium25

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. ISO 16750-2:2023 Road vehicles, Environmental conditions and testing for electrical and electronic equipment, Part 2: Electrical loads · International Organization for Standardization · standard · retrieved 2026-10-27
  3. Achieving reverse battery protection using TI high side switch controllers (SLUAAN7) · Texas Instruments · vendor-doc · retrieved 2026-10-27
  4. Reverse current/battery protection circuits (SLVA139) · Texas Instruments · vendor-doc · retrieved 2026-10-27
  5. Reverse battery protection for high side switches (SLVAE55) · Texas Instruments · vendor-doc · retrieved 2026-10-27
  6. Basics of ideal diodes (SLVAE57) · Texas Instruments · vendor-doc · retrieved 2026-10-27
  7. Fuse (electrical) · Wikipedia · reference · retrieved 2026-10-27
  8. TPS1H100-Q1 40-V, 100-mOhm single-channel smart high-side power switch data sheet · Texas Instruments · vendor-doc · retrieved 2026-10-27