Chassis dyno (chassis dynamometer)

chassis dynamometerrolling roadroller dynohub dynowheel dyno

A chassis dyno is a dynamometer that measures a complete vehicle's output at the driven wheels or hubs, with its transmission and driveline in place. Roller types read force where the tire meets the roller; hub types bolt to the wheel hubs. Results are wheel figures, lower than crank figures by the drivetrain loss.Medium354

How it works

Inertia chassis dynos use heavy rollers of known mass and calculate power from how quickly the car accelerates them.

EngineLabs notes they are quick to set up and very repeatable for back-to-back comparisons but cannot hold steady-state load points without an added absorber.Medium43

Load-bearing dynos add an absorber, usually eddy current, to the rollers. It applies controlled resistance so the car can be held at a fixed rpm and load or swept at a set ramp rate, and a load cell measures torque directly. They usually read slightly lower than inertia dynos.Medium47

Hub dynos replace the wheels with adapters bolted to the hubs that drive absorbers. Nicholson McLaren describes a hydraulic hub system that computes work from absorber pressure and hub speed, with no tire slip, no rolling resistance and no straps.Medium5

Wheel figures sit below crank figures because the gearbox, differential, joints, bearings and tires all absorb power. Wikipedia cites a range of 15 to 20 percent, but the real loss varies with layout, gear, fluid temperature and tire, so a fixed percentage only approximates crank output.Medium36

AWD vehicles need front and rear rollers or hub units that turn together. If one axle stands still, the center coupling and stability systems see a speed difference and react, which corrupts the run or triggers torque cuts.Low52

Typical values

Drivetrain lossWikipedia cites a range of 15 to 20 percentVaries with layout, gear and fluid temperatureSourced · medium3
Inertia versus loaded readingsInertia dynos usually read higher than loaded steady-state dynosSourced · medium4
Hub dyno interface
  • Adapters on the wheel hubs
  • No tires, rollers or straps
Sourced · medium5
Eddy-current absorber
  • No holding torque at zero speed
  • Cannot motor the car
Sourced · medium7
Variables that change readings

Tire pressure, strap tension, drivetrain fluid temperature, back-to-back heat

Sourced · medium4
Typical chassis absorber coolingAir-cooled eddy units with heavy steel rotorsRotor mass adds useful inertiaSourced · medium7

How an ECU uses it

A chassis dyno sees only roller or hub speed and force; the ECU log shows what happened inside the engine.

Log engine speed, load, lambda, timing, knock, boost and temperatures, and on roller dynos compare wheel speed with roller speed to spot tire slip.Medium41

Roller dynos often take engine rpm from roller speed and a ratio set at the start of the run. Check dyno rpm against ECU rpm in a steady gear before trusting a torque curve, because a wrong ratio distorts torque per rpm.Low4

Vehicle systems react to the dyno. On a two-wheel dyno, traction and stability control see stationary wheels on the other axle and may cut torque, so they often need a dyno mode or switching off.Low2

How to test it

5 checks, in order.

  1. Set tire pressure to the same value every session and inspect the tires for damage, since roller speed and heat stress them.Medium4
  2. Strap the car with the same anchor points and tension each time. EngineLabs and Nicholson McLaren both note that strap tension changes tire loading and the reading.Medium45
  3. Place fans for the radiator and intercooler and log intake air temperature. A car on rollers gets none of the ram airflow it sees on the road.Low4
  4. Run sweeps in the same gear, from the same start rpm and temperature, with the same correction standard. Make three runs and check their spread before comparing modifications.Medium4
  5. Safety
    Keep people out of the line of the tires and rollers, check wheel fasteners and straps before every run, and have an extinguisher ready. A tire failure or strap release at speed can throw debris or the car.Low54

Symptoms and causes

Torque curve dips or spikes at high load

Likely causes Tire slip on the roller, strap movement or knock

Check Compare wheel speed with roller speed and check the knock log for the same moment.

Medium45

Readings fall run after run

Likely causes Heat soak in drivetrain fluid, intake air or tires

Check Compare start temperatures and cool the car to the same point between runs.

Medium4

Large difference from another shop's sheet

Likely causes Different dyno type, correction standard or ramp rate

Check Check the correction standard and dyno type before comparing; compare changes on one dyno.

Medium4

Stability or traction warnings during a run

Likely causes Speed mismatch between driven and non-driven axles

Check Use the vehicle's dyno mode or disable the systems the maker allows.

Low2

In tuning

Use a loaded roller or hub dyno to build tables, since steady-state holds let you tune part-throttle cells.

Use inertia runs for quick before-and-after comparisons where repeatability matters more than holding a point.Medium45

Report wheel figures as wheel figures. Converting to crank with a fixed percentage hides the real loss, which changes with driveline, gear and temperature.Medium36

Try it

psi
°F
%
hp

Result

SAE J1349 factor1.017 :1
STD (SAE J607) factor1.055 :1

Planning estimate from the formula below, not a measurement.

Open the full dyno correction factor calculator (sae j1349 and std) →

Common mistakes

Mistake Converting wheel figures to crank figures with one fixed percentage.

Do instead Quote wheel figures as measured; Wikipedia's cited range of 15 to 20 percent is a rough guide, not a constant.Medium3

Mistake Comparing an inertia dyno sheet with a loaded dyno sheet.

Do instead Compare changes made on the same dyno; EngineLabs notes inertia designs usually read higher.Medium4

Mistake Inconsistent strapping or tire pressure between sessions.

Do instead Record strap points, tension and pressures, and repeat them every time.Medium45

Myths vs facts

Myth The dyno that reads highest is the most accurate.

Fact EngineLabs notes inertia dynos usually read higher, while loaded dynos measure torque with a load cell and usually read slightly lower. The difference reflects method, not accuracy.Medium4

Myth A hub dyno measures crank power.

Fact A hub dyno measures at the hubs, after the gearbox, differential and axles. Removing the tires and rollers removes slip and rolling resistance, but drivetrain loss is still included.Medium56

Myth Drivetrain loss is a fixed percentage.

Fact Losses vary with driveline type, gear, fluid temperature and tires. Wikipedia's range of 15 to 20 percent is a general figure, not a rule for any one car.Medium36

Frequently asked

How does a chassis dyno work?

The car drives rollers or hub adapters with its own transmission. An inertia dyno calculates power from how fast heavy rollers accelerate; a loaded dyno adds an absorber and measures torque with a load cell. The result is power at the wheels, after drivetrain loss.Medium345

Why do different dynos read differently?

Design, correction standard and setup all matter. Inertia dynos usually read higher than loaded dynos, and tire pressure, strap tension, ramp rate and drivetrain temperature all change the figure. Compare before-and-after changes on one dyno rather than peak numbers across shops.Medium4

What is the difference between an inertia dyno and a load-bearing dyno?

An inertia dyno has fixed-mass rollers and calculates power from their acceleration, so it cannot hold a steady load. A load-bearing dyno adds an absorber, usually eddy current, that can hold a set rpm and load for steady-state tuning and measures torque with a load cell.Medium43

How much power is lost through the drivetrain?

It varies. Wikipedia cites wheel figures generally 15 to 20 percent below crank figures, but the real loss depends on driveline layout, gear, fluid temperature and tires. Treat any fixed percentage as an estimate, and compare wheel figures with wheel figures.Medium36

Is a hub dyno more accurate than a roller dyno?

It removes several variables. A hub dyno bolts to the hubs, so there is no tire slip, rolling resistance or strap effect, and it can hold load precisely. It still measures after the gearbox and differential, so its figures are not crank figures.Medium5

Wiring, pinouts and parts

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. Traction control system · Wikipedia · reference · retrieved 2026-10-27
  3. Dynamometer · Wikipedia · reference · retrieved 2026-10-27
  4. The Data And Accuracy Implications Of Different Dynamometer Designs (Bradley Iger, May 2018) · EngineLabs · press · retrieved 2026-10-27
  5. Hub Dyno testing · Nicholson McLaren Engines · vendor-doc · retrieved 2026-10-27
  6. Horsepower · Wikipedia · reference · retrieved 2026-10-27
  7. Eddy current brake · Wikipedia · reference · retrieved 2026-10-27