CDI ignition

capacitor discharge ignitionCDICD ignitionthyristor ignitionDC-CDIAC-CDI

CDI ignition (capacitor discharge ignition) is an ignition system that charges a capacitor to a few hundred volts and dumps it through the coil primary with a fast switch. The result is a very fast-rising spark voltage. It is common on motorcycles, small engines, outboards and aftermarket race ignition boxes.45

How it works

In CDI ignition a converter raises supply voltage to roughly 250 to 600 V and stores it in a capacitor.

At the trigger signal a thyristor (SCR) closes and discharges the capacitor into the primary of an ignition coil, which steps it up to the plug firing voltage.4

Here the coil acts as a pulse transformer, not an energy store. Because energy is already waiting in the capacitor, there is no dwell to build up. Voltage rises at about 3 to 10 kV per microsecond, compared with roughly 300 to 500 V per microsecond for inductive systems.Medium41

The fast rise makes CDI tolerant of fouled or wet plugs, because the voltage reaches breakdown before current can leak away across deposits. The tradeoff is a short spark, roughly 50 to 600 microseconds, which can be too brief for reliable ignition of lean or dilute mixtures.Medium4

AC-CDI units take power straight from an alternator or magneto winding and suit simple small engines. DC-CDI units run from the battery through an inverter to 400 to 600 V, which gives more consistent energy at cranking speed. Many race boxes fire several sparks per event at low rpm to offset the short duration.4

Typical values

Capacitor charge voltageAbout 250-600 VDC-CDI: 400-600 V from a 12 V inverterSourced · medium4
Secondary voltage riseAbout 3-10 kV per microsecondInductive: about 0.3-0.5 kV per microsecondSourced · medium4
Spark durationAbout 50-600 microsecondsInductive coils often exceed 1 msLow confidence42
Stored energyAbout 50 mJ or morePoints-type Kettering systems: about 25 mJ at low speedSourced · medium4
Inductive comparison (Bosch P65-TWG)
  • Rise 1.4 kV per microsecond or less
  • Spark up to about 1.85 ms
Shows the long-arc, slower-rise inductive alternativeSourced2

How an ECU uses it

With CDI, the ECU or trigger module only needs to command the firing instant.

There is no dwell calculation, so timing accuracy at very high rpm is easier, which is one reason CDI suits small high-speed engines and rotaries.Medium41

When an ECU drives an external CDI box, it usually sends a short logic-level trigger per spark. The box handles charging and discharge internally. Some boxes need a fixed short pulse rather than a dwell-length pulse, so the ECU output mode must match the box's input specification.Low41

How to test it

4 checks, in order.

  1. Safety
    a CDI capacitor holds several hundred volts even with the engine stopped and can give a dangerous shock. Disconnect power and wait before handling the module or its coil terminals.Medium4
  2. Confirm the trigger first. Check that the pickup or ECU trigger signal reaches the CDI input while cranking, using a scope or LED test light. A missing trigger looks exactly like a dead CDI.Medium14
  3. Check supply. On a DC-CDI, measure battery voltage at the module while cranking; on an AC-CDI, check the charging coil output against the service manual. Low input voltage gives a weak or missing spark.Medium4
  4. Check spark with an adjustable gap tester. A CDI spark is thin and fast, so judge whether it fires the gap every time rather than how fat it looks. Substitute a known-good module if trigger and supply are both correct.Low46

Symptoms and causes

No spark at all

Likely causes No trigger signal, failed capacitor or SCR, open charging coil

Check Scope the trigger input, then measure supply or charging coil output

Medium4

Misfire at high rpm only

Likely causes Capacitor not recharging fully between sparks, weak supply

Check Measure supply voltage at the module under load at high rpm

Low4

Lean or dilute mixture misfires

Likely causes Spark duration too short for the mixture

Check Compare with a longer-duration inductive spark or a multi-spark setting

Low43

Hard starting with a weak battery (DC-CDI)

Likely causes Low inverter input voltage

Check Measure battery voltage at the module while cranking

Medium4

In tuning

CDI shines where fouling is a risk

Rich two-strokes, oily rotaries and high-rpm small engines. Inductive ignition with ample dwell is often preferred on lean-burn or high-EGR engines, where a longer arc helps the flame kernel grow.Medium43

Multi-spark modes help cold start and idle but must taper off with rpm, because the capacitor needs time to recharge. Check that a race box's rev limit and multi-spark settings suit the engine's maximum rpm.Medium4

Common mistakes

Mistake Using an ordinary inductive coil with a CDI box without checking the maker's coil specification.

Do instead Use the coil type the CDI maker specifies; the primary inductance changes how fast the pulse rises.Low41

Mistake Condemning the CDI box before checking the trigger and supply.

Do instead Scope the trigger input and measure supply voltage first; most no-spark faults are upstream.Medium4

Myths vs facts

Myth CDI always makes a stronger spark than inductive ignition.

Fact CDI gives a faster voltage rise, not more energy in every case. Its spark is much shorter, so an inductive coil can deliver comparable or more total energy over a longer arc.Medium42

Myth CDI boxes add power on their own.

Fact Ignition only needs to light the mixture reliably. Once misfire is gone, a hotter spark adds no power; claimed gains come from fixing a weak original system.Medium43

Frequently asked

How does a CDI ignition work?

A CDI charges a capacitor to a few hundred volts, then a thyristor dumps it into the ignition coil primary when the trigger arrives. The coil steps that pulse up to tens of kilovolts, producing a very fast-rising but short spark at the plug.4

What is the difference between CDI and inductive ignition?

Inductive ignition stores energy in the coil's magnetic field during dwell and gives a slower-rising, longer spark. CDI stores energy in a capacitor and gives a much faster rise and shorter spark, which resists fouling but suits lean mixtures less well.Medium42

What are the symptoms of a bad CDI?

Common signs are no spark, intermittent cutting out when hot, misfire at high rpm and hard starting. Check the trigger signal and supply voltage before replacing the module, because a missing pickup signal or low battery voltage produces the same symptoms.Medium4

What is the difference between AC CDI and DC CDI?

AC-CDI charges its capacitor from an alternator or magneto winding, so spark energy depends on engine speed. DC-CDI runs from the battery through an inverter at 400 to 600 V, giving steadier energy at cranking and more precise control.Medium4

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Automotive Handbook, 10th edition · Robert Bosch GmbH · book · retrieved 2026-10-27
  2. Ignition Coil P65-TWG data sheet · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  3. Internal Combustion Engine Fundamentals, 2nd edition (J. B. Heywood) · McGraw-Hill Education · book · retrieved 2026-10-27
  4. Capacitor discharge ignition · Wikipedia · reference · retrieved 2026-10-27
  5. Ignition system · Wikipedia · reference · retrieved 2026-10-27
  6. Spark plug · Wikipedia · reference · retrieved 2026-10-27