Ignition coil

coilspark coilcoil packstick coilpencil coilcanister coil

An ignition coil is a step-up transformer that turns 12 V battery power into the 10,000 to 40,000 V pulse that jumps a spark plug gap. It stores energy in a magnetic field while primary current flows, then releases it as high voltage when the ECU or igniter switches that current off.461

How it works

An ignition coil has a primary winding of relatively few turns of heavy wire and a secondary winding of thousands of turns of fine wire, both on a laminated iron core. The turns ratio sets how much the collapsing primary voltage is multiplied on the secondary side.64

While the switch is closed, primary current ramps up and stores energy in the core. This charging period is dwell. When the switch opens, the field collapses and the primary flies back to a few hundred volts, which the turns ratio steps up to tens of kilovolts on the secondary.16

Output voltage is available voltage. The plug only draws as much as it needs to break down the gap, which is required voltage. Spark plugs typically need about 12 to 25 kV and can need up to 45 kV.

The margin between available and required voltage is what prevents misfire.81

Coil designs evolved from oil-filled canister coils feeding a distributor, to wasted-spark coil packs firing two cylinders, to one coil per cylinder. Coil-on-plug and pencil or stick coils sit directly on the plug. Many modern coils add an internal igniter transistor, so the ECU sends only a logic-level trigger.642

Typical values

Secondary output10-40kVAvailable voltage; depends on coil design and dwellSourced46
Plug firing requirementAbout 12-25 kV, up to 45 kVRises with gap, cylinder pressure and electrode wearSourced · medium8
Primary current (Bosch P65-TWG example)Up to 7.0 ASet by dwell; higher current means more stored energySourced2
Dwell for 7 A (P65-TWG example)
  • 3.94 ms at 12 V
  • 3.07 ms at 14 V
Lower battery voltage needs longer dwellSourced2
Spark energy (P65-TWG example)63.6 mJ at 7 A primarySpecified minimum is 65 mJ classSourced2
Spark duration (P65-TWG example)About 1.4-1.9 msInductive coils give a long, lower-current arcSourced2
High-voltage rise time (P65-TWG)1.4 kV per microsecond or lessSlower than CDI systemsSourced25

How an ECU uses it

The ECU schedules two events per spark

When to start charging (dwell start) and when to cut current (spark). It computes dwell start backward from the spark angle, using engine speed so the coil reaches target current exactly when the spark is due.12

Dwell is read from a table against battery voltage, because primary current rises more slowly at low voltage. The Bosch P65-TWG needs about 3.9 ms at 12 V but only about 3.1 ms at 14 V for 7 A. Too little dwell weakens the spark; too much overheats the coil and driver.21

A dumb coil needs the ECU's own ignition driver (an IGBT or similar) to switch primary current. A coil with an integrated igniter takes a low-current trigger signal, about 10 to 20 mA for the P65-TWG, and the ECU output must match that type.24

How to test it

5 checks, in order.

  1. Safety
    secondary output can exceed 30 kV. Never hold a lead or coil while cranking, keep electronics clear and use an insulated spark tester rather than a screwdriver against the block.Medium23
  2. Read stored misfire codes and per-cylinder misfire counters with a scan tool first. Swap the suspect coil to another cylinder; if the misfire follows the coil, the coil is the cause. If it stays, look at the plug, injector or compression.Medium31
  3. Inspect the coil body and boot for cracks, carbon tracks, oil or water contamination and corroded terminals. Denso lists these, plus low battery voltage and damaged wiring, as common causes of early coil failure.3
  4. On a dumb coil, measure primary and secondary resistance with a multimeter and compare with the service manual figure. Many coils with built-in igniters cannot be measured this way; Bosch lists the P65-TWG resistances as not measurable.Medium21
  5. For a load test, fit an adjustable spark-gap tester and check the coil fires a wide gap consistently. A scope on the primary or secondary shows dwell length, firing voltage and burn time, which reveals weak coils that still pass a resistance check.Medium18

Symptoms and causes

Misfire under boost or heavy load only

Likely causes Coil output too low for the higher required voltage, plug gap too wide, or a tracking boot

Check Close the plug gap slightly; if the misfire stops, the coil margin was marginal

Medium78

Single-cylinder misfire code

Likely causes Failed coil, worn plug, injector or compression fault

Check Swap the coil to another cylinder and see whether the code follows

Medium3

Hesitation or stumble on acceleration

Likely causes Weak coil, cracked boot arcing to the head, low battery voltage

Check Inspect for carbon tracks and measure battery voltage at the coil while cranking

Medium3

Engine stalls but restarts

Likely causes Intermittent coil or igniter failure, often when hot

Check Log RPM and battery voltage; check coil connectors and grounds

Medium3

Coils failing repeatedly

Likely causes Excess dwell, oil in the plug well, vibration or wrong plug

Check Check the dwell table against the coil data sheet and fix the oil leak

Medium32

In tuning

Boost raises cylinder pressure at the spark, and breakdown voltage rises roughly with pressure times gap.

A coil that fires cleanly naturally aspirated can misfire at high boost. Closing the plug gap lowers required voltage and is usually the first fix.Medium78

Set dwell from the coil maker's data, not from another coil's table. Dwell must also shrink at high rpm on wasted-spark and single-coil layouts, because the time between sparks falls. Check that the dwell table covers low cranking voltage.21

Try it

V
V

Ignition driver saturation plus wiring loss; about 1-2 V is typical for an IGBT driver.

Ω

Illustrative default, not for any specific coil. Measure, or use the coil maker's data.

mH
A
rpm

Result

Dwell at this voltage (modelled)1.88 ms
Dwell at 10 V2.95 ms
Dwell at 12 V2.30 ms
Dwell at 14 V1.88 ms
Stored energy at target current73.5 mJ
Coil time constant L ÷ R6.00 ms
Share of time between sparks11.0 %

Modelled from an ideal RL circuit, not from a coil's measured data. Coil makers' dwell tables take priority; too much dwell overheats coils and drivers.

Planning estimate from the formula below, not a measurement.

Open the full ignition coil dwell calculator (modelled dwell vs battery voltage) →

Common mistakes

Mistake Copying a dwell table from a different coil.

Do instead Use the maker's dwell versus voltage data and verify current with a clamp meter or scope.2

Mistake Driving a coil with an internal igniter from a high-current ECU output, or a dumb coil from a logic output.

Do instead Confirm whether the coil has an integrated igniter and match the ECU output type.24

Mistake Replacing a coil without fixing the cause.

Do instead Check for oil in the plug wells, worn plugs and wiring faults first, or the new coil fails the same way.3

Myths vs facts

Myth A coil rated at 40 kV always delivers 40 kV.

Fact That figure is available voltage. The coil only reaches the voltage the gap needs to break down. Extra rating is margin, which matters under boost and with worn plugs.81

Myth More dwell always means a stronger spark.

Fact Energy rises with primary current only up to the coil's design limit. Beyond it, extra dwell adds heat, not useful energy, and shortens coil and driver life.2

Frequently asked

How does an ignition coil work?

Current flows through the primary winding during dwell and stores energy in the magnetic core. When the ECU or igniter cuts that current, the field collapses and the secondary winding, with far more turns, produces a high-voltage pulse that jumps the spark plug gap.61

How many volts does an ignition coil produce?

Most automotive coils can supply roughly 10,000 to 40,000 V. The spark plug usually needs about 12 to 25 kV to fire, and up to 45 kV under high cylinder pressure, so the coil only reaches the voltage the gap demands.Medium48

What are the symptoms of a bad ignition coil?

Typical signs are a misfire on one cylinder, hesitation under acceleration, rough idle, stalling that restarts, and a check engine light with a misfire code. On boosted engines a weak coil often misfires only at high load, when the plug needs the most voltage.Medium37

How do you test an ignition coil?

Swap the coil to another cylinder and see whether the misfire follows it. Then inspect for cracks and carbon tracks, check primary and secondary resistance against the service figure on coils without igniters, and confirm spark with an adjustable gap tester or a scope.Medium31

Why does dwell change with battery voltage?

Primary current rises more slowly at lower voltage, so the coil needs longer charging time to reach the same current. Bosch's P65-TWG data shows about 3.9 ms at 12 V but about 3.1 ms at 14 V for 7 A, which is why ECUs use a dwell versus voltage table.2

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Automotive Handbook, 10th edition · Robert Bosch GmbH · book · retrieved 2026-10-27
  2. Ignition Coil P65-TWG data sheet · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  3. Ignition Coils Product Information Catalogue · DENSO Aftermarket Europe · vendor-doc · retrieved 2026-10-27
  4. DENSO highlights the evolution of the ignition coil · DENSO Aftermarket Europe · vendor-doc · retrieved 2026-10-27
  5. Capacitor discharge ignition · Wikipedia · reference · retrieved 2026-10-27
  6. Ignition coil · Wikipedia · reference · retrieved 2026-10-27
  7. Paschen's law · Wikipedia · reference · retrieved 2026-10-27
  8. Spark plug · Wikipedia · reference · retrieved 2026-10-27