Ignition dwell

dwell timecoil charge timedwell anglecoil dwell

Ignition dwell is the time the ignition coil's primary winding is switched on and charging before the spark. When the driver switches off, the stored magnetic energy collapses into the secondary winding and fires the plug. Dwell is set in milliseconds and corrected for battery voltage.12

How it works

An inductive ignition coil stores energy in its magnetic field while current flows through the primary winding.

Current does not jump to its final value. It rises over time, limited by winding inductance and resistance, so the coil needs a certain charge time to reach its target current.34

Dwell is that charge time. In old contact-breaker systems it was measured as a cam angle, called dwell angle. Electronic systems control it as time, because the coil needs the same milliseconds to charge regardless of engine speed.23

Battery voltage changes how fast the current rises. Lower voltage needs longer dwell for the same current. Bosch publishes this as a table: for its P65-TWG coil at 7.0 A, the listed dwell is about 3.94 ms at 12 V and 3.07 ms at 14 V.1

At high rpm the time between sparks shrinks. On a coil that fires once per cycle there is more time than on one shared between cylinders or firing every revolution, which is why coil-per-cylinder layouts make high-rpm dwell easier.Medium35

In tuning

Dwell should come from the coil maker's data, not guesswork.

Too short gives weak sparks and misfire under boost or high load. Too long overheats the coil and its driver and wastes current once the coil is saturated.13

Bosch states that its table values exclude loom resistance and that the needed dwell should be verified by current measurement. A current clamp and oscilloscope on the primary circuit show whether the coil reaches its rated current at each voltage.1

Check the driver type too. Some coils include their own power transistor and need a low-current logic trigger. Others need the controller to switch the full primary current.

Mismatching the two can destroy the coil or the controller output.1

Formula and worked example

θ_dwell = t_dwell × N × 0.006
θ_dwell
crankshaft degrees covered while the coil chargesdeg
t_dwell
dwell timems
N
engine speedrpm
0.006
conversion: 360 degrees per revolution divided by 60,000 ms per minutedeg/(ms·rpm)
23

Try it

A
V
%
°F

Hot engine bays raise copper resistance about 0.4% per °C.

Result

Smallest AWG: 10 AWG2.25 %voltage drop
Smallest metric: 4 mm²2.96 %voltage drop

Voltage drop is one check. The wire must also be rated for the current at its temperature and bundling, and the fuse must protect the wire.

Planning estimate from the formula below, not a measurement.

Open the full automotive wire gauge calculator →

Myths vs facts

Myth More dwell always means a bigger spark.

Fact Once the primary current reaches its limit, extra dwell only heats the coil and driver. Spark energy stops rising.14

Myth Dwell is measured in degrees on modern engines.

Fact Electronic ignition controls dwell as time in milliseconds. Dwell angle is a carryover from contact-breaker distributors.23

Myth One dwell value suits every coil.

Fact Dwell depends on the coil's inductance, resistance, rated current and driver. Use the specific coil's published table.1

Frequently asked

What happens if dwell is too long?

Too much dwell keeps current flowing after the coil is fully charged. The coil and its driver transistor heat up, the coil can fail or the driver can burn out, and the system draws extra current. Spark energy does not improve once the coil has reached its rated primary current.Medium14

What happens if dwell is too short?

Too little dwell means the coil never reaches its rated current, so it stores less energy and produces a weaker, shorter spark. Under high cylinder pressure, such as boost or high load, a weak spark can fail to jump the plug gap and the engine misfires.Medium43

Why does dwell change with battery voltage?

Primary current rises at a rate set by the applied voltage and the coil's inductance and resistance. With less voltage the current climbs more slowly, so the coil needs longer to reach the same current. Controllers use a dwell-versus-voltage table to keep spark energy steady as system voltage varies.13

How do you set coil dwell?

Start from the coil manufacturer's dwell-versus-voltage table for its rated current. Enter it into the controller, then measure the actual primary current with a current clamp and oscilloscope at several voltages. Adjust until the coil reaches its rated current without staying saturated. Bosch states table values exclude loom resistance.1

What is dwell angle?

Dwell angle is the number of distributor cam degrees during which contact-breaker points stayed closed and charged the coil. It was set by the points gap. Electronic ignition systems replaced it with dwell time in milliseconds, because the coil needs a fixed charge time regardless of rpm.Medium2

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Ignition Coil P65-TWG data sheet · Bosch Motorsport · vendor-doc · retrieved 2026-10-25
  2. Dwell angle · Wikipedia · reference · retrieved 2026-10-25
  3. Automotive Handbook, 10th edition · Robert Bosch GmbH · book · retrieved 2026-10-25
  4. Ignition coil · Wikipedia · reference · retrieved 2026-10-25
  5. Wasted spark · Wikipedia · reference · retrieved 2026-10-25