Spark plug heat range

heat rangehot plugcold plugplug heat rating

Spark plug heat range is a measure of how quickly a plug moves heat from its firing tip into the cylinder head. A hot plug keeps more heat in the tip to burn off deposits; a cold plug sheds heat faster to avoid overheating and pre-ignition. It says nothing about spark strength.37

How it works

Spark plug heat range is set by the length of the insulator nose and its heat path to the metal shell.

A long nose gives a long path, so the tip runs hotter. A short nose gives a short path, so heat flows into the head and coolant faster.37

The tip must stay inside a temperature window, roughly 500 to 800 °C (932 to 1,472 °F). Below it, carbon deposits do not burn off and the plug fouls. Above it, the ceramic and electrodes can glow and ignite the mixture before the spark.Medium73

Numbering differs by brand. NGK and Denso use higher numbers for colder plugs. Champion, Bosch, Beru and ACDelco use higher numbers for hotter plugs.

Numbers cannot be swapped between brands as equals, so use a maker's cross-reference.72

Typical values

Tip operating windowAbout 500-800 °C932-1,472 °FToo cold fouls; too hot risks pre-ignitionSourced · medium7
NGK and Denso numberingHigher number = colder plugSourced72
Champion, Bosch, Beru, ACDelcoHigher number = hotter plugDo not cross numbers between brandsSourced7
Typical automotive gap0.6-1.8mm0.024-0.071 inBoosted engines usually run the smaller endSourced · medium7
Firing voltage neededAbout 12-25 kV, up to 45 kVHigher with wider gap and higher pressureSourced · medium7

How an ECU uses it

The ECU never measures plug temperature, but plug choice affects what it sees.

A plug that runs too hot can cause pre-ignition that knock control cannot cure, because retarding the spark does nothing for ignition that starts before the spark.63

Some OEM ECUs use ionization current through the plug for misfire and knock detection. Fouled or wrong-heat-range plugs change that signal, which is one reason the factory range should be the default.Low41

How to test it

4 checks, in order.

  1. Run the engine at the condition you want to judge, ideally sustained high load, then cut the engine without idling. Idle running quickly overwrites the marks left by full-load running.7
  2. Remove the plugs and inspect the insulator nose under magnification. A light tan or gray color suggests the right range; black sooty deposits suggest too cold or rich; a white, blistered or glazed insulator suggests too hot.Medium7
  3. Look at the ground strap and center electrode. Rounded or melted electrodes and specks of aluminum on the insulator point to severe overheating, pre-ignition or detonation. Check the piston before going back to load.Medium76
  4. Check the gap with a wire or disc gauge, not a flat feeler gauge, before installation. Do not regap fine-wire iridium or platinum plugs by bending near the precious-metal tip.7

Symptoms and causes

Fouled plugs, misfire at idle or cold start

Likely causes Plug too cold for the use, rich mixture, oil consumption

Check Check mixture and oil use first; go one step hotter only if both are correct

Medium37

Blistered white insulator, eroded electrodes

Likely causes Plug too hot, lean mixture, over-advanced timing

Check Check lambda and timing logs at the load where the damage occurs

Medium7

Knock that does not respond to timing retard

Likely causes Pre-ignition from an overheated plug tip

Check Fit plugs one step colder and recheck at the same load

Medium63

Misfire at high boost with new plugs

Likely causes Gap too wide for the coil, not a heat range issue

Check Close the gap and retest before changing heat range

Medium57

In tuning

Adding boost, nitrous or compression raises combustion heat at the plug tip, so tuned engines often run one or more steps colder than stock. The goal is a tip that stays below the glow point at sustained full load but still self-cleans at idle.Medium37

Higher cylinder pressure also raises the voltage needed to fire the gap. Boosted engines usually close the gap at the same time as going colder, so the coil keeps enough margin to avoid high-load misfire.Medium57

Do not use a hotter plug to hide rich fueling or oil burning. NGK notes that hotter plugs reduce the pre-ignition safety margin; fix the fueling or mechanical problem instead.3

Common mistakes

Mistake Assuming a higher number is always colder.

Do instead That is true for NGK and Denso but backwards for Champion, Bosch, Beru and ACDelco. Use the brand's cross-reference.7

Mistake Going several steps colder on a street engine.

Do instead Change one step at a time and read the plugs; too cold causes fouling and misfire at idle and in traffic.Medium37

Mistake Reading plugs after idling back to the pits.

Do instead Cut the engine straight after the load run, because idling erases the full-load evidence.7

Myths vs facts

Myth A hotter plug gives a hotter spark.

Fact Heat range only describes how fast the tip sheds heat to the head. Spark energy comes from the coil and ignition system, not from the plug's heat range.3

Myth A colder plug cools the combustion chamber.

Fact The plug is not a heat sink for the chamber. A colder plug only keeps its own tip cooler, which removes it as a pre-ignition source.3

Frequently asked

What does spark plug heat range mean?

It describes how quickly the plug transfers heat from its firing tip to the cylinder head. A hot plug keeps the tip hotter to burn off deposits, while a cold plug sheds heat faster to prevent the tip from glowing and causing pre-ignition.37

Is a higher NGK number hotter or colder?

Colder. On NGK and Denso plugs a higher heat range number means a colder plug. Champion, Bosch, Beru and ACDelco use the opposite convention, so never compare numbers across brands without the maker's cross-reference chart.72

Do I need colder spark plugs for a turbo?

Often yes. Boost raises combustion heat at the plug tip, so many boosted engines run one step colder than stock to keep the tip below the glow point. Change one step at a time, close the gap for boost and read the plugs after a load run.Medium37

What happens if a spark plug is too hot?

The tip can overheat and glow, igniting the mixture before the spark. That pre-ignition raises cylinder temperature and pressure fast and can melt electrodes or hole a piston. Signs include a blistered white insulator and eroded electrodes.76

What happens if a spark plug is too cold?

The tip never reaches self-cleaning temperature, so carbon builds up on the insulator. The deposits can conduct current away from the gap and cause misfire, especially at idle, in traffic and on cold starts. Check mixture and oil use before going hotter.73

Wiring, pinouts and parts

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Automotive Handbook, 10th edition · Robert Bosch GmbH · book · retrieved 2026-10-27
  2. DENSO updates its spark plug heat range information · DENSO Aftermarket Europe · vendor-doc · retrieved 2026-10-27
  3. Understanding Spark Plug Heat Range · NGK Spark Plugs · vendor-doc · retrieved 2026-10-27
  4. Capacitor discharge ignition · Wikipedia · reference · retrieved 2026-10-27
  5. Paschen's law · Wikipedia · reference · retrieved 2026-10-27
  6. Pre-ignition · Wikipedia · reference · retrieved 2026-10-27
  7. Spark plug · Wikipedia · reference · retrieved 2026-10-27