Ignition coil dwell calculator (modelled dwell vs battery voltage)

Modelled coil dwell = −(L ÷ R) × ln(1 − I × R ÷ V): the time the primary current needs to reach its target at the available voltage. Lower battery voltage needs longer dwell. Enter coil resistance, inductance and target current to build a starting dwell table.

V
V

Ignition driver saturation plus wiring loss; about 1-2 V is typical for an IGBT driver.

Ω

Illustrative default, not for any specific coil. Measure, or use the coil maker's data.

mH
A
rpm

Result

Dwell at this voltage (modelled)1.88 ms
Dwell at 10 V2.95 ms
Dwell at 12 V2.30 ms
Dwell at 14 V1.88 ms
Stored energy at target current73.5 mJ
Coil time constant L ÷ R6.00 ms
Share of time between sparks11.0 %

Modelled from an ideal RL circuit, not from a coil's measured data. Coil makers' dwell tables take priority; too much dwell overheats coils and drivers.

Planning estimate from the formula below, not a measurement.

How it works

The formula, the method step by step, then a worked example.

i(t) = (V ÷ R)(1 − e^(−t R ÷ L));  dwell = −(L ÷ R) × ln(1 − I × R ÷ V);  V = V_batt − V_drop;  E = ½ L I²
  1. The coil primary is an inductor in series with its resistance, so current rises exponentially towards V ÷ R with time constant L ÷ R.
  2. Solve for the time at which the current reaches the target; that is the dwell.
  3. At lower voltage the current rises more slowly and the ceiling (V ÷ R) is lower, so the dwell is longer.
  4. Energy stored in the coil at the end of dwell is half the inductance times the current squared.

Worked example

Inputs

Battery voltage
14 V
Driver and wiring drop
1 V
Primary resistance
0.5 Ω
Primary inductance
3 mH
Target peak primary current
7 A
Engine speed
7000 rpm
Coil layout
1

Result

Dwell at this voltage (modelled)1.88ms
Dwell at 10 V2.95ms
Dwell at 12 V2.30ms
Dwell at 14 V1.88ms
Stored energy at target current73.5mJ
Coil time constant L ÷ R6.00ms
Share of time between sparks11.0%

Assumptions and limits

  • Modelled curve: ideal, constant inductance and resistance. Real coils saturate and warm up, which changes both.
  • Defaults are illustrative and do not describe any specific coil.
  • Smart coils with built-in drivers may limit current themselves; follow the maker's dwell table.

Related terms

Frequently asked

Why does dwell need to increase at low voltage?

Coil current builds more slowly at lower voltage, and its ceiling (voltage ÷ resistance) is lower. To reach the same peak current, and spark energy, the ECU needs more time. Dwell tables therefore fall as battery voltage rises.

Can I use this to set my coil's dwell table?

Only as a starting point. The result is modelled from an ideal circuit. Use the coil maker's dwell data where available, and check coil and driver temperatures; too much dwell overheats both.

What is a typical coil dwell time?

Many coil-on-plug coils run roughly 2-4 ms at 14 V, but it varies widely by coil. Measure resistance and inductance, or use the maker's table, rather than copying another coil's figures.

Answers draw on the sources below.

Sources

  1. Transients in an inductor (RL time constant) · HyperPhysics, Georgia State University · retrieved 2026-10-27
  2. Automotive Handbook · Robert Bosch GmbH

Spot an error? Tell us.