Electric fan controller

fan controllerradiator fan controllercooling fan controllerPWM fan controllerfan relay controller

An electric fan controller is the circuit that decides when a radiator cooling fan runs and how fast. It reads coolant temperature from a thermo-switch or sensor, applies separate on and off thresholds, and switches the fan through a relay, solid state switch or PWM driver. Many also respond to air conditioning requests and run the fan after key-off.Medium1091

How it works

Electric fans replaced belt-driven fans on most cars because they deliver airflow at idle and in traffic regardless of engine speed, and draw no power when cooling is not needed. A thermostatic switch or the engine control unit switches them.Medium10

The simplest electric fan controller is a thermo-switch in the coolant that closes at a fixed temperature and energizes a relay. Adjustable controllers read a coolant temperature sensor instead, and an ECU does the same in software, with an off point below the on point so the fan does not chatter.Medium101

A PWM controller varies fan speed by switching the motor on and off many times per second and changing the on-time fraction. Airflow follows demand, the fan starts softly instead of slamming on, and average current falls at part speed. The switch must be a semiconductor stage, not a mechanical relay.Medium94

A fan motor draws a large inrush at start, because a stationary motor has no back EMF to limit current and draws near its stall current. The relay contacts, fuse and wiring must survive that surge every cycle, which is why soft starts and staggered dual-fan starts reduce stress and voltage dips.Medium811

Typical values

Motorsport PDM fan-capable channels
  • 15 A continuous / 100 A peak
  • 25 A / 150 A
Bosch PBX 190 high-side outputsSourced2
Motor start-up currentNear stall current until the motor builds speedSeveral times running current; size switch and fuse for itSourced · medium8
PWM frequency limit, smart high-side switch2kHz maximumTI TPS1H100-Q1; fan drivers each specify their own rangeSourced4
Fan-on threshold

Above the thermostat opening temperature, off point a few degrees lower

Engine-specific; set from coolant logsSourced · medium101
Fuse rating ruleAt or below the wire's ampacity, above fan running currentThe fuse protects the wire and must ride through start-up surgeSourced · medium65
Automotive blade fuse ranges
  • Mini 2-30 A
  • Regular 0.5-40 A
  • Maxi 20-120 A
Sourced · medium7

How an ECU uses it

An ECU fan output is usually a low-side driver that grounds a relay coil, or a signal to a PDM channel.

The ECU compares coolant temperature with fan-on and fan-off thresholds, and dual-fan setups add a second, higher stage or a second PWM range.Medium13

Most strategies force the fan on with an air conditioning request, because the condenser needs airflow at idle. Many also run the fan after key-off until coolant falls below a threshold or a timer expires, which needs a fan feed that stays live with the ignition off.Medium101

A PDM or smart switch adds current measurement. The controller can then flag a seized or dragging fan by high current, an open motor or broken wire by near-zero current, and ramp the fan in with PWM instead of hitting it with full voltage.Medium24

How to test it

5 checks, in order.

  1. Log coolant temperature with a scan tool or the ECU and note when the fan turns on and off as the engine warms at idle. Compare with the calibrated thresholds or the thermo-switch rating. A fan that never starts with coolant above the on point points to the controller, relay, fuse or motor.Medium110
  2. Command the fan on and measure voltage at the fan connector under load. It should be close to battery voltage; a drop of more than about half a volt suggests a worn relay contact, a poor connector or a bad ground.Low13
  3. Power the fan directly from the battery through a fused jumper to prove the motor. Read running current with a clamp meter and compare it with the maker's rating. Current well above rating means a dragging or seizing motor.Medium86
  4. On PWM controllers, scope the output. Duty cycle should rise with coolant temperature and the frequency should match the driver's specification. An output stuck at 0% or 100% while temperature changes points to the input sensor or the controller settings.Medium94
  5. Safety
    keep hands, tools and loose clothing clear of the blades. A fan with run-on can start with the ignition off, so unplug the fan connector or disconnect the battery before reaching near it.Medium1

Symptoms and causes

Engine overheats in traffic but is fine at speed

Likely causes Fan not running: blown fuse, failed relay, threshold set too high, failed motor or coolant sensor

Check Command or jumper the fan; if it runs, the fault is in the control side, not the motor.

Medium101

Fan runs constantly, even on a cold engine

Likely causes Relay or switch stuck on, ECU failsafe running the fan on a failed coolant sensor, or a stuck AC request

Check Read the coolant sensor value and the AC request input, then pull the relay and see if the fan stops.

Medium112

Fan fuse blows on start-up

Likely causes Inrush exceeds the fuse rating, seized motor or chafed wire

Check Clamp-meter start-up and running current; a dragging motor shows high running current too.

Medium86

Lights dim and idle dips when the fan starts

Likely causes Inrush loading the charging system, undersized wire or a poor ground

Check Log battery voltage at fan switch-on; a soft start or staged fans reduce the dip.

Medium813

Fan relay chatters on and off

Likely causes On and off thresholds too close together, or a voltage dip at fan start resetting the controller

Check Log coolant temperature against fan state and widen the gap between on and off points.

Medium1

In tuning

Set the fan-on point above the thermostat opening temperature so the thermostat regulates first, and set the off point a few degrees lower. A fan threshold below the thermostat temperature keeps the fan running constantly and adds electrical load without lowering coolant temperature.Medium101

Coolant temperature feeds fuel, ignition and idle corrections, so a fan strategy that lets temperature swing widely makes those corrections swing too. Proportional PWM control holds coolant steadier than on-off switching, which keeps calibration logs cleaner.Medium91

Try it

A
:1

Typical surge multipliers, used only to flag a PDM channel's inrush allowance. Check the load's own data.

%

80% is the common sizing rule: the fuse is 125% of the steady current.

in
%
V
°F
A
A
A

Result

Fuse or current-limit rating20.0 A
Recommended wire (mm²)2.08 14 AWG
Voltage drop with this wire0.37 V
Smallest for ampacity (mm²)1.31 16 AWG, 21.3 A derated
Smallest for voltage drop (mm²)2.08 14 AWG
Estimated start-up surge90 A
Channel load60 %
PDM total load60 %

Start-up surge exceeds the channel rating: check the PDM's inrush time allowance for this channel.

Planning estimate from the formula below, not a measurement.

Open the full pdm channel fuse and wire size calculator →

Common mistakes

Mistake Running fan current straight through a thermo-switch or toggle.

Do instead Most probe switches cannot carry fan current. Let the switch drive a relay coil or a solid state switch rated for the fan's inrush.Medium118

Mistake Fusing to the fan's running current only.

Do instead The fuse must protect the wire and ride through start-up surge. Size the wire for the load and length, then fuse at or below the wire's rating.Medium65

Mistake Setting the fan to turn on below the thermostat opening temperature.

Do instead Set it above; otherwise the fan runs constantly and the thermostat never controls coolant temperature.Medium10

Mistake PWM-driving a fan through a mechanical relay.

Do instead Relays cannot switch at PWM rates and wear out fast. Use a MOSFET driver or a PDM PWM channel.Medium119

Myths vs facts

Myth Turning the fan on earlier makes the engine run cooler.

Fact While the thermostat is regulating, it sets coolant temperature. Running the fan below that point only adds electrical load; extra airflow lowers temperature only when the radiator is at its limit.Medium101

Myth PWM fans are just slower relay fans.

Fact PWM varies motor power continuously, softens inrush and cuts current at part speed. It needs a semiconductor driver, and the fan motor must tolerate the switching frequency.Medium94

Myth A fan running after shutdown means something is wrong.

Fact Many cars run the fan after key-off by design to clear heat soak, stopping on a timer or a temperature threshold. Running until the battery is flat is the fault.Medium1

Frequently asked

What temperature should an electric fan turn on?

Set it above the thermostat's opening temperature so the thermostat regulates first, with the off point a few degrees lower to stop chatter. The right value depends on the engine and thermostat, so confirm it against coolant logs at idle and in traffic rather than copying another car's number.Medium101

Do I need a relay for an electric fan?

Yes, unless a solid state switch or PDM channel drives it. A radiator fan draws far more current than a thermo-switch, toggle or ECU output can carry, especially at start-up. The control device switches the relay coil, and the relay carries the fan current.Medium118

What size fuse do I need for an electric radiator fan?

Pick the wire first for the fan's rated running current and the run length, then a fuse at or below that wire's rating that still survives start-up surge. Use the fan maker's current rating, not a guess. A PDM channel with an inrush delay handles motor surge well.Medium658

Why does my radiator fan run after the engine is off?

Usually by design. After shutdown, coolant stops flowing and heat soaks out of the engine, so many controllers run the fan until temperature drops or a timer expires. If it runs until the battery is flat, suspect a stuck relay, a failed coolant sensor or a controller that never sleeps.Medium110

Is PWM fan control better than a relay?

For most cars, yes. PWM matches airflow to demand, starts the fan softly and holds coolant temperature steadier than on-off switching. It costs more and needs a MOSFET driver rated for the fan current. A relay is simpler and cheaper, and works fine for a basic setup.Medium94

Wiring, pinouts and parts

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

13 sources
  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. PowerBox PBX 190 data sheet 75077387 · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  3. TPL7407L 40-V 7-channel low side driver data sheet (SLRS066) · Texas Instruments · vendor-doc · retrieved 2026-10-27
  4. TPS1H100-Q1 40-V, 100-mOhm single-channel smart high-side power switch data sheet · Texas Instruments · vendor-doc · retrieved 2026-10-27
  5. Ampacity · Wikipedia · reference · retrieved 2026-10-27
  6. Fuse (electrical) · Wikipedia · reference · retrieved 2026-10-27
  7. Fuse (automotive) · Wikipedia · reference · retrieved 2026-10-27
  8. Inrush current · Wikipedia · reference · retrieved 2026-10-27
  9. Pulse-width modulation · Wikipedia · reference · retrieved 2026-10-27
  10. Radiator (engine cooling) · Wikipedia · reference · retrieved 2026-10-27
  11. Relay · Wikipedia · reference · retrieved 2026-10-27
  12. Solid-state relay · Wikipedia · reference · retrieved 2026-10-27
  13. Voltage drop · Wikipedia · reference · retrieved 2026-10-27