Centrifugal supercharger

centrifugal blowerbelt-driven centrifugal compressordynamic superchargerhead unitVortechProChargerPaxton

A centrifugal supercharger is a belt-driven dynamic compressor that spins an impeller at very high speed through a step-up gearbox, flinging air outward and converting its velocity into pressure. It works like the compressor half of a turbocharger, but the crankshaft drives it, so boost rises steeply with engine speed.125

How it works

A centrifugal supercharger draws air into the eye of the impeller, accelerates it outward through the blades, then slows it in a diffuser and volute so velocity turns into pressure. The impeller must spin many times faster than the engine, so a crank pulley drives an internal step-up gear set. Vortech's V-30, for example, uses a 4.21:1 internal ratio.25

Pressure rise from a centrifugal compressor scales roughly with the square of impeller tip speed, a result of the turbomachine affinity laws. Because impeller speed is locked to engine speed, a unit that makes 10 psi (69 kPa) at redline makes only about a quarter of that at half the rpm. Boost climbs steadily and peaks at the top.Medium21

A centrifugal head unit has a compressor map just like a turbo: pressure ratio against corrected airflow, with speed lines, efficiency islands, a surge line on the left and a choke region on the right. Pick the compressor and pulley ratio so the engine's operating line crosses the efficient islands near peak rpm and stays clear of surge.42

Surge is the main hazard. When the throttle snaps shut at high rpm, the impeller is still turning fast but flow collapses, pushing the compressor left of the surge line. A blow-off or bypass valve vents or recirculates the trapped charge so flow ramps down smoothly, protecting the impeller, bearings and gears.42

Dynamic superchargers are typically quoted at about 70-85% peak efficiency, higher than a Roots at high boost, so charge temperature is usually lower for the same pressure. Compression still heats the air, and most high-boost systems use an air-to-air or air-to-water intercooler between the head unit and the throttle.Medium16

Typical values

Boost vs impeller speedPressure rise roughly proportional to tip speed squaredApproximation from the affinity lawsSourced · medium2
Internal step-up ratio (example)4.21:1 on the Vortech V-30Ratios differ by model and makerSourced · medium5
Peak efficiency, dynamic superchargersAbout 70-85%Uncited figure in a secondary summary; maker maps differLow confidence1
Map efficiency contours (example map)56-76% isentropicSourced · medium2
Inlet depression from filter and ducting1 psi or more on some intake systems6.9 kPaRaises pressure ratio for the same gauge boostSourced4
Pressure ratio example

12 psi (83 kPa) gauge at sea level with 1 psi inlet loss: 26.7 ÷ 13.7 ≈ 1.95

Sourced4

How an ECU uses it

Speed-density is common on centrifugal kits.

A MAP sensor in the manifold reads boost directly and must cover the highest absolute pressure; place the IAT sensor after the intercooler, near the throttle or in the plenum. Because boost tracks rpm, the VE table sees a steadily rising load line through every gear.76

With a MAF, the meter usually sits ahead of the head unit, in the draw-through position. Any air vented to atmosphere after the MAF, such as through a vent-style blow-off valve, has been metered but never reaches the cylinders, so the engine runs rich and may stall on lift-off. A recirculating bypass avoids this.Medium47

Some systems mount the MAF after the compressor, in the blow-through position, where it reads pressurized, hotter air. Then the meter must be sized and calibrated for boost, and the bypass must return air upstream of the head unit so the reading still matches cylinder airflow.Medium7

How to test it

5 checks, in order.

  1. Inspect the drive with the engine off and the key out. Check belt wear, tension and alignment, and look for glazing or rubber dust. High impeller speed needs a lot of drive torque near redline, so slip shows up there first.Medium51
  2. Spin the impeller input by hand with the belt off. It should turn smoothly with no grinding, notchiness or axial play you can feel. Check the head unit's oil level or feed line and drain if it is not self-contained.Low5
  3. Log MAP, rpm, IAT and knock on a full-throttle pull in one gear. Boost should rise smoothly and peak near redline. Boost that flattens or falls at the top points to belt slip, a leak or a bypass that opens under boost.Medium14
  4. Check the bypass or blow-off valve. Apply vacuum with a hand pump to confirm it opens and holds, then confirm the spring keeps it shut under full boost. A fluttering or barking sound on lift-off means the valve is too stiff, too small or not plumbed to manifold reference.Medium4
  5. Safety
    keep clear of belts and fans with the engine running, and never run the engine with the inlet duct off, since the impeller can ingest debris or fingers. Wear eye protection during pressure tests and stay below the rated pressure of the intercooler and couplers.Medium27

Symptoms and causes

Boost drops or flattens near redline

Likely causes Belt slip, boost leak, bypass valve opening early, inlet restriction

Check Look for belt dust, pressure-test the tract and confirm the valve stays shut with a pressure reference

Medium41

Fluttering or barking on throttle lift

Likely causes Compressor surge from a missing, undersized or stuck bypass valve

Check Watch the valve with a helper snapping the throttle, and check its vacuum line and spring rate

42

Rich stumble or stall when lifting off with a MAF

Likely causes Metered air vented to atmosphere by a blow-off valve, or a leak after the meter

Check Plumb the valve to recirculate before the head unit and recheck fuel trims

Medium47

Knock or timing retard only at the top of the rev range

Likely causes Peak boost and charge temperature arrive together near redline, intercooler too small, low octane

Check Log IAT and knock against rpm; a rising IAT trace near redline points to charge cooling

Medium61

In tuning

Because boost rises with rpm, the high-load area of the maps is reached near redline, not at the torque peak.

Fuel and timing must be built along a rising load line, and knock margin is usually tightest at the top, where boost, charge temperature and cylinder pressure all peak together.Medium61

A smaller crank-to-blower pulley ratio raises impeller speed and therefore boost at every rpm, roughly with the square of the speed change. Check fuel headroom first: injector duty and fuel pressure must hold at the new peak, and the rev limiter caps impeller speed, so keep it at or below the maker's limit.Medium27

Treat the bypass as part of the calibration. With speed-density, a vent-to-atmosphere valve is fine for fueling; with a MAF it is not. Either way, transient fueling must handle the boost collapse and recovery around each shift.Medium47

Formula and worked example

Δp2 ≈ Δp1 × (N2 / N1)²
Δp1
pressure rise at the original impeller speedpsi or kPa
Δp2
estimated pressure rise at the new impeller speedpsi or kPa
N1, N2
original and new impeller speeds at the same engine rpmrpm
Medium2

Try it

psi
ft
psi
psi

Result

Pressure ratio2.29 :1
Ambient pressure14.70 psi
Manifold absolute pressure29.4 psi

Planning estimate from the formula below, not a measurement.

Open the full turbo pressure ratio calculator →

Common mistakes

Mistake Venting the blow-off valve to atmosphere on a MAF car.

Do instead Recirculate the bypass air to the inlet between the MAF and the head unit so metered air stays in the system.Medium47

Mistake Raising the rev limit without checking impeller speed.

Do instead Impeller speed rises with engine speed times the drive and gear ratios. Calculate it at the new limit and stay inside the maker's maximum.Medium52

Mistake Judging the setup from low-rpm boost.

Do instead A centrifugal makes little boost at low rpm by design. Judge it at the top of the rev range and size fuel and cooling for that point.1

Myths vs facts

Myth A centrifugal supercharger is just a turbo without lag.

Fact It uses the same kind of compressor, but impeller speed is tied to engine speed, so boost is low at low rpm and rises steadily. A turbo can make full boost in the midrange once the exhaust spools it up.12

Myth Belt-driven blowers do not need a blow-off valve.

Fact The impeller keeps spinning at engine speed when the throttle closes, so flow collapses while pressure stays high. That drives the compressor into surge, which a bypass or blow-off valve prevents.42

Myth A smaller pulley always means more power.

Fact More impeller speed raises boost, but it also raises drive load, belt slip risk and charge temperature, and can push the compressor toward choke where efficiency falls. Past that point extra boost brings mostly heat.Medium24

Frequently asked

How does a centrifugal supercharger work?

A belt from the crankshaft drives a step-up gearbox that spins an impeller many times faster than the engine. The impeller throws air outward at high speed, and the diffuser and volute slow it down, turning velocity into pressure. The pressurized air then flows to the intake, usually through an intercooler.25

Why does a centrifugal supercharger make more boost at high rpm?

Its pressure rise grows roughly with the square of impeller speed, and impeller speed is tied to engine speed by the belt and gears. Doubling engine rpm roughly quadruples the pressure rise, so boost is small at low rpm and peaks near redline.Medium21

Does a centrifugal supercharger need a blow-off valve?

Yes, in almost every case. When the throttle closes at high rpm, the impeller keeps spinning while flow collapses, pushing the compressor into surge. A bypass or blow-off valve releases that pressure. On MAF cars, recirculate it to the inlet so measured air is not lost.47

Is a centrifugal supercharger better than a Roots?

For top-end efficiency, usually yes. A centrifugal compressor runs cooler at high boost and packages like a turbo. A Roots or twin-screw gives strong boost from low rpm. The better choice depends on whether you want low-speed torque or high-rpm power with lower charge temperatures.Medium13

How do you increase boost on a centrifugal supercharger?

Raise impeller speed with a smaller blower pulley or a larger crank pulley. Boost rises roughly with the square of the speed change. Stay within the head unit's maximum impeller speed, and check fuel headroom, belt grip and charge temperature before running the new setting hard.Medium257

Wiring, pinouts and parts

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Supercharger · Wikipedia · reference · retrieved 2026-10-27
  2. Centrifugal compressor · Wikipedia · reference · retrieved 2026-10-27
  3. Roots-type supercharger · Wikipedia · reference · retrieved 2026-10-27
  4. Turbo Tech 103 (Expert): compressor maps · Garrett Motion (Honeywell) · vendor-doc · retrieved 2026-10-27
  5. Big Boost: Breaking Down Vortech's Lineup Of V-30 Superchargers · Dragzine · press · retrieved 2026-10-27
  6. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-27
  7. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27