Roots supercharger

Roots blowerRoots-type superchargerlobe blowerpositive displacement blowerEaton TVS6-71 blower

A Roots supercharger is a belt-driven, positive displacement blower that uses two meshing lobed rotors to carry a fixed volume of air per revolution from inlet to outlet. It does not compress air internally. Boost builds because the engine cannot swallow the air as fast as the rotors deliver it.125

How it works

A Roots supercharger traps air in the pockets between each rotor lobe and the housing, then carries it around the outside of the rotors to the outlet. Timing gears keep the rotors from touching. Because each revolution moves a nearly fixed volume, airflow rises almost in step with blower speed, which is why boost arrives at low engine speed.12

There is no reduction in pocket volume inside the housing. When a pocket opens to the outlet, higher-pressure manifold air rushes back into it and the mixture is pushed out. This backflow compression is irreversible, so a Roots blower turns more drive work into heat than a compressor that squeezes air internally, and the penalty grows with pressure ratio.15

Efficiency falls as boost rises. Wikipedia puts a Roots blower at about 70% efficiency near a pressure ratio of 2.0 and roughly 50-58% at 15 psi (103 kPa) of boost. A larger blower turned more slowly for the same boost usually runs more efficiently than a small one spun hard.

Maker figures differ, so treat any one value as approximate.Medium124

Modern Roots units twist the lobes into a helix to smooth the pulses. Eaton's first rotors used three lobes with a 60° twist; the TVS (Twin Vortices Series) uses four lobes with a 160° twist, and the later R2650 uses 170°. Eaton credits the extra lobe, twist and redesigned ports with better efficiency and lower noise.Medium3

Because the drive comes straight off the crankshaft, the blower always costs some engine output to turn, even at light load. Most factory and aftermarket Roots systems add a bypass valve that opens at part throttle so the blower can recirculate air instead of compressing it, cutting drive loss and heat when boost is not requested.Medium264

Typical values

Internal compression
  • None
  • Outlet pressure is set by the engine and manifold restriction downstream
Sourced15
Adiabatic efficiency
  • About 70% near pressure ratio 2.0
  • About 50-58% at 15 psi boost103 kPa
Secondary summary; vendor comparisons quote 30-65%Sourced · medium14
Volumetric efficiencyUsually above 90% except at the lowest blower speedsSourced · medium1
Eaton TVS rotor geometry
  • Four lobes, 160° twist
  • R2650 uses 170°
Earlier Eaton units: three lobes, 60° twistSourced · medium3
Classic GMC-pattern displacementA 6-71 blower moves about 339 cu in (5.6 L) per revolutionSourced · medium2
Boost curve shapeNear flat across the rpm range once the blower is up to speedSourced2

How an ECU uses it

On speed-density, the MAP sensor in the manifold after the blower reads boost directly, so the sensor range must cover the highest absolute pressure plus margin. Place the IAT sensor after the blower and any intercooler core. Charge temperature after a Roots blower can be far above ambient, and the density correction must see it.65

With a MAF, the meter must sit upstream of the blower, and the bypass must recirculate within the metered tract. Air that leaves the system after being measured, through a leak or a vent-to-atmosphere valve, makes the engine run rich because the ECU fuels air that never reaches the cylinders.Medium62

The bypass valve changes what the load signal means. With it open, manifold pressure sits in vacuum even at fairly large throttle angles; as it closes, MAP climbs fast. Transient fueling and knock control must track that pressure rise rather than throttle position alone.Medium65

How to test it

5 checks, in order.

  1. Inspect the drive first. With the engine off and the key out, check belt condition, tension and pulley alignment. Glazing, black dust around the pulleys or a chirp on throttle snaps points to belt slip, which lowers blower speed and boost.Medium26
  2. Log MAP, rpm and IAT on a full-throttle pull in one gear. A healthy Roots system holds near-flat boost once up to speed. Boost that sags as rpm rises suggests belt slip, a leak or a bypass that is not fully closed.Medium21
  3. Check the bypass actuator. With a hand vacuum pump, apply vacuum to the actuator and confirm it holds and moves the valve freely through its travel. At idle the valve should be open; under boost it must close fully.Medium6
  4. Leak-test the pressurized tract. With the engine off, cap the inlet, pressurize the system with regulated shop air below your boost target, and listen or spray soapy water at couplers, gaskets and the bypass. Any hiss under pressure is a boost leak.Medium6
  5. Safety
    keep hands, tools and loose clothing away from belts and fans with the engine running, and remove the key before any belt work. Wear eye protection when pressurizing the intake, and never exceed the pressure the couplers and intercooler are rated for.Medium6

Symptoms and causes

Boost lower than expected or falling at high rpm

Likely causes Belt slip, bypass valve not fully closing, boost leak, inlet restriction

Check Look for belt dust and chirp, verify the bypass closes under boost, then run a pressure leak test

Medium26

Knock or timing retard late in long pulls

Likely causes Charge temperature rise from blower heat, intercooler heat soak, fuel octane too low

Check Log IAT after the intercooler across the pull; a climbing IAT points to heat, a flat IAT to fuel or timing

Medium51

Rich running and black smoke on lift-off with a MAF

Likely causes Metered air vented to atmosphere, or a leak after the MAF

Check Confirm the bypass recirculates to the inlet after the MAF and leak-test the tract

Medium6

Rough idle or hunting after a kit install

Likely causes Bypass valve stuck, vacuum leak at the blower or manifold gasket, wrong MAF or injector scaling

Check Check fuel trims at idle, smoke-test for vacuum leaks and confirm the bypass actuator holds vacuum

Medium6

In tuning

A Roots blower delivers near-peak cylinder filling from low rpm, so the high-load areas of the fuel and ignition maps are reached at engine speeds that saw only light load before. Fuel and timing must be set for that load across the whole rpm range, not just near the redline.Medium25

Heat is the limit. Charge temperature rises through the run and with each pulley step, so knock margin shrinks as boost climbs. Use IAT-based timing reduction, log knock across repeated pulls and check that the intercooler holds temperature before chasing more boost.Medium51

Check fuel headroom before any pulley change. More boost raises airflow, so confirm injector duty and fuel pressure stay inside their limits at the new peak, and remember the blower's drive load also rises with boost.Medium62

Formula and worked example

T2 = T1 × [1 + (PR^0.286 − 1) / η]
T2
blower outlet temperature (absolute)K
T1
blower inlet temperature (absolute)K
PR
pressure ratio, absolute outlet over absolute inlet pressure
η
adiabatic (isentropic) efficiency as a fraction
5

Try it

°F
:1

Absolute outlet ÷ absolute inlet pressure. Use the turbo pressure ratio calculator if you know boost instead.

%

Read it from the compressor map island at your operating point; 65-78% is typical of modern compressors.

Result

Compressor outlet temperature238 °F
Temperature rise158 °F
Ideal (isentropic) outlet temperature198 °F
Charge density vs inlet air1.55 :1before any intercooling

Planning estimate from the formula below, not a measurement.

Open the full turbo compressor outlet temperature calculator →

Common mistakes

Mistake Mounting the IAT sensor in the inlet ahead of the blower.

Do instead Read charge temperature after the blower and intercooler core, where it reflects what the cylinders receive.65

Mistake Overdriving a small blower to reach a boost target.

Do instead Efficiency falls as speed and pressure ratio rise; a larger blower turned slower usually makes the same boost with less heat.Medium1

Mistake Fitting a smaller pulley without checking fuel and spark headroom.

Do instead Log injector duty, fuel pressure, IAT and knock at the new peak boost before calling the change done.Medium65

Myths vs facts

Myth A Roots blower compresses air inside its housing.

Fact It only displaces air. Pressure rises when outlet-side air flows back into each opening pocket and when the engine cannot swallow the delivered volume. That backflow compression is why a Roots runs hotter than an internal-compression design at the same boost.15

Myth A supercharger has no lag, so it needs no transient tuning.

Fact Boost follows engine speed closely, but the bypass valve closing and the manifold filling still produce a fast pressure rise. Acceleration fueling and knock control must follow MAP during that step, or the engine leans out or knocks on tip-in.Medium65

Myth A supercharger adds power for free because it does not restrict the exhaust.

Fact The crankshaft drives the blower, so part of the engine's gross output is spent turning it, and that share grows with boost. A bypass valve reduces the loss at part throttle but cannot remove it under boost.26

Frequently asked

How does a Roots supercharger work?

Two meshing lobed rotors, driven by a belt from the crankshaft, trap air between the lobes and housing and carry it to the outlet. Each revolution moves a nearly fixed volume. The engine cannot take that air as fast as it arrives, so pressure builds in the manifold.12

Is a Roots or twin-screw supercharger better?

It depends on the goal. Both give strong low-speed boost. A twin-screw compresses air internally, so it usually runs cooler and more efficiently at higher boost. A Roots is simpler and often cheaper, and modern twisted-lobe designs have narrowed the gap at moderate pressure ratios.Medium213

Is the Eaton TVS a Roots supercharger?

Yes. The Eaton TVS is a Roots-type positive displacement blower with two four-lobe rotors twisted 160°, or 170° on the later R2650. The twist and redesigned ports smooth airflow and improve efficiency and noise, but it still has no internal compression.Medium31

Do Roots superchargers need an intercooler?

Not always, but most benefit. Backflow compression heats the charge more than an internal-compression blower does, and hotter air is less dense and more knock-prone. Most modern factory Roots systems use an air-to-water core under or inside the blower housing for that reason.Medium15

Why do Roots blowers make so much heat?

The air is not squeezed gradually. When each pocket opens to the outlet, hot pressurized air rushes back in and mixes, which wastes work as heat. The loss grows with pressure ratio, so outlet temperature climbs faster with boost than on twin-screw or centrifugal units.15

Wiring, pinouts and parts

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Roots-type supercharger · Wikipedia · reference · retrieved 2026-10-27
  2. Supercharger · Wikipedia · reference · retrieved 2026-10-27
  3. Eaton adds supercharger oomph (TVS R2650) · Gardner Business Media · press · retrieved 2026-10-27
  4. Twin Screw System · Whipple Superchargers · vendor-doc · retrieved 2026-10-27
  5. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-27
  6. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27