Individual cylinder trim

cylinder trimper-cylinder fuel trimindividual cylinder fuel correctioncylinder balanceper-cylinder ignition trimICT

Individual cylinder trim is an ECU correction that adjusts fuel or ignition timing for one cylinder relative to the others. It compensates for uneven airflow, fuel distribution, injector tolerance or knock tendency between cylinders, so each runs closer to the intended mixture and spark advance.Medium123

How it works

Cylinders on the same engine do not breathe or fuel identically.

Intake runner shape, plenum position, exhaust pulse interaction and cam timing differences make volumetric efficiency vary between cylinders. Heywood describes cylinder-to-cylinder variation in mixture and charge as a normal feature of multi-cylinder engines.2

Injectors also vary within their flow tolerance, and wear or deposits widen the spread over time. A trim table, usually a percentage per cylinder that may vary with rpm and load, lets the ECU add or remove fuel for one cylinder without changing the main table.Medium13

Ignition trim works the same way for spark advance. A cylinder with a hotter end-gas region or poorer cooling may knock first. Retarding only that cylinder protects it while the others keep their advance.

Knock control systems with per-cylinder detection apply this automatically.Medium41

In tuning

Trim needs per-cylinder measurement.

Individual exhaust temperature probes, per-runner wideband sensors or per-cylinder knock data show where cylinders differ. EGT differences can come from timing as well as mixture, so confirm with lambda before trimming fuel on temperature alone.Medium52

Fix hardware problems first. A clogged injector, vacuum leak or failing coil should be repaired, not trimmed around. Use trims for the consistent residual differences that remain on healthy hardware.Medium1

Formula and worked example

Myths vs facts

Myth Per-cylinder trim is only for race engines.

Fact Factory ECUs on many production engines balance cylinders using crank speed fluctuation or knock sensing. Aftermarket trim tables apply the same idea manually.Medium1

Myth One wideband in the collector shows each cylinder's mixture.

Fact A collector sensor reads the average of several cylinders. One rich and one lean cylinder can average to the target, hiding the difference.72

Frequently asked

Why does one cylinder run lean?

Common causes are uneven airflow from the intake design, an injector flowing below the others, a vacuum leak near one runner, or exhaust scavenging that pulls more air through one cylinder. Diagnose the cause with injector flow testing and per-cylinder measurement before using trim to correct a remaining difference.Medium21

How do you balance cylinders with EGT?

Fit a thermocouple in each exhaust runner at equal distance from the port, log them together and compare at steady load. Higher temperature can mean leaner mixture or later combustion, so confirm with lambda where possible. Trim fuel or timing in small steps and recheck at several operating points.Medium52

Should you trim timing per cylinder?

Where knock data shows that one cylinder reaches the knock limit before the others, yes. Retarding only that cylinder keeps margin there without giving up advance on the rest. Use per-cylinder knock data and make small changes; ignition guidance here is qualitative only.Medium41

Is per-cylinder trim a fix for bad injectors?

No. Trim corrects small, consistent differences. A faulty injector may vary from cycle to cycle, leak or spray poorly, which a fixed trim cannot fix. Clean, flow test or replace injectors first, ideally as a matched set, then trim what remains.Medium13

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-27
  3. Fuel injection · Wikipedia · reference · retrieved 2026-10-27
  4. Engine knocking · Wikipedia · reference · retrieved 2026-10-27
  5. Exhaust gas temperature gauge · Wikipedia · reference · retrieved 2026-10-27
  6. Air-fuel ratio · Wikipedia · reference · retrieved 2026-10-27
  7. Lambda Sensor LSU 4.9 product page · Bosch Motorsport · vendor-doc · retrieved 2026-10-27