Oxygen (O2) sensor

O2 sensorlambda sensorlambda probeexhaust gas oxygen sensorEGO sensorHO2S

An O2 sensor (oxygen sensor, or lambda sensor) is an exhaust sensor that measures how much oxygen is left after combustion, telling the ECU whether the mixture is rich or lean. Narrowband sensors switch sharply at stoichiometry; wideband sensors measure the actual lambda value. Modern cars fit one before and one after each catalytic converter.32

How it works

Most O2 sensors use a zirconia (zirconium dioxide) ceramic that conducts oxygen ions when hot.

One side sees exhaust, the other a reference, usually outside air. The oxygen difference creates a voltage: Bosch quotes about 20 to 900 mV for its switching sensors, high when rich and low when lean.32

That narrowband output is steep and nonlinear around lambda 1, near 0.45 V, which is ideal for holding stoichiometry and poor for reading how rich or lean. A wideband sensor adds an oxygen pump cell; the pump current needed to balance the measuring cell gives a continuous reading, zero at lambda 1.234

Titania sensors work differently. Titanium dioxide changes resistance with oxygen, low when rich and high when lean, so the ECU supplies a current and reads a voltage between near 0 and about 5 V. They need no reference air but are far less common than zirconia.Medium2

Zirconia works only when hot, from roughly 316 °C (600 °F). Unheated sensors waited minutes for exhaust heat. Heaters bring older finger sensors to about 350 °C (662 °F), while planar sensors integrate the heater for faster readiness.

The Bosch LSU 4.9 wideband heater draws 7.5 W in steady state.234

Position sets the job. The upstream (control) sensor sits after the manifold merge and before the catalyst and drives fuel control. The downstream (diagnostic) sensor sits after the catalyst and lets the ECU judge how well the catalyst works.32

Typical values

Narrowband outputabout 20-900 mVHigh when rich, low when lean; about 0.45 V near lambda 1Sourced32
Zirconia working temperaturefrom about 316 °C600 °FSourced · medium2
Finger sensor heater targetup to 350 °C662 °FSourced3
Wideband range (Bosch LSU 4.9)lambda 0.65 to free airSourced4
LSU 4.9 heater7.5 W steady state, 7.5 V nominalSourced4
LSU 4.9 exhaust gas limit930 °C continuous, 1,030 °C briefly1,706 °F · 1,886 °FSourced4
Titania outputnear 0 to about 5 Vresistance typeSourced · medium2
Service life
  • Heated about 100,000 mi160,000 km
  • Unheated 30,000-50,000 mi
Sourced · medium2

How an ECU uses it

In closed loop, the ECU trims fuel around the upstream narrowband signal.

It adds fuel until the sensor reads rich, removes fuel until it reads lean, and the switching averages near stoichiometric. The accumulated corrections become short-term and long-term fuel trims.Medium21

US rules require on-board monitoring of catalyst efficiency and of the oxygen sensors themselves. A healthy catalyst stores oxygen, so the downstream signal stays steady while the upstream one switches; a downstream signal that mirrors the upstream one indicates a worn catalyst.523

The ECU also drives and monitors the heater circuit, and it ignores the sensor until it is hot enough to trust. Heater faults set their own codes and keep the engine in open loop longer after a cold start.Medium35

How to test it

6 checks, in order.

  1. Read codes and live data first. Separate heater-circuit codes from slow-response or stuck-signal codes, since they point to different failures. Note fuel trims: large trims with a sensor that still switches normally suggest a fuel or air problem, not the sensor.Medium51
  2. Warm the engine fully and hold a steady fast idle. The upstream narrowband should swing repeatedly between roughly 0.1-0.2 V and 0.8-0.9 V. A signal stuck high, stuck low or switching slowly is suspect.Medium23
  3. Force the mixture to check response. A throttle snap should drive the signal rich, and a small induced intake leak should drive it lean. A good sensor follows promptly; a lazy one lags or barely moves.Low2
  4. Check the heater. Unplug the sensor, measure heater resistance across the heater pins against the maker's figure, then confirm battery voltage on the heater supply with the key on. The narrowband hub page lists typical pinouts.Medium34
  5. Remove the sensor and read the tip. White or light-gray deposits suggest silicone or coolant silicates, an oily black coating suggests oil burning, and black powdery soot suggests rich running. Fix the cause before fitting a new sensor.Medium2
  6. Safety
    exhaust parts stay hot long after a run. Let the system cool before removal, and use only the thread compound supplied on the new sensor, keeping it off the tip.Medium43

Symptoms and causes

Check engine light with a heater-circuit code

Likely causes Open heater element, blown fuse or relay, or damaged wiring.

Check Measure heater resistance and heater supply voltage.

Medium3

Poor fuel economy, rich smell, sooty tailpipe

Likely causes Sensor stuck lean so the ECU adds fuel, an exhaust leak ahead of the sensor, or genuinely rich fueling.

Check Compare sensor voltage with fuel trims and smoke-test for exhaust leaks upstream of the sensor.

Medium2

Catalyst efficiency code

Likely causes Worn catalyst, failing downstream sensor or an exhaust leak near it.

Check Compare upstream and downstream traces; a steady downstream signal with the code points to the sensor or a leak.

Medium52

Slow switching and drifting fuel trims

Likely causes Contamination from silicone, coolant silicates, oil or leaded fuel, or plain age.

Check Inspect tip deposits and test response with forced rich and lean conditions.

Medium2

Long open-loop time after a cold start

Likely causes Weak heater or a sensor mounted in a cool spot.

Check Log time from start to closed loop and check heater resistance and supply.

Low32

In tuning

A narrowband sensor cannot tell a tuner how rich the engine is at full load, because its output barely changes away from lambda 1.

Tune with a wideband and leave the narrowbands for factory closed-loop fueling.24

Headers, turbo pipes and relocated sensors change sensor temperature and the gas it sees. Mount upstream sensors where gas is hot and representative, tip down with the wire upward where possible, away from the tailpipe outlet, and fix any leak ahead of them.4

Keep downstream sensors and catalyst monitors working on a road vehicle. Catalyst monitoring is a required emissions function, and hiding a catalyst fault from it is treated as tampering under US law.56

Try it

:1
%

0 for E0 gasoline, 10 for E10, 85 for nominal E85.

Result

Lambda0.850 :1
Stoichiometric AFR of this blend14.70 :1

Planning estimate from the formula below, not a measurement.

Open the full afr to lambda converter →

Common mistakes

Mistake Using silicone sealant or the wrong anti-seize near the sensor.

Do instead Silicones poison zirconia elements. Use sensor-safe sealants and only the grease supplied on the new sensor's threads.Medium24

Mistake Replacing a sensor that is reporting a real fault.

Do instead A sensor reading lean because of a vacuum or exhaust leak is working. Check fuel trims and leaks first.Medium21

Mistake Tuning full-load fuel from narrowband voltage.

Do instead Narrowband output is nearly flat away from lambda 1. Fit a wideband for any fuel tuning.24

Safety, legal and emissions

Legal

On US road vehicles, the Clean Air Act prohibits removing or disabling emissions controls, and EPA treats parts that fool emissions monitors as defeat devices. This is general information, not legal advice.6

Myths vs facts

Myth Higher O2 sensor voltage means more oxygen.

Fact On a zirconia narrowband it is the opposite. High voltage means little oxygen (rich) and low voltage means excess oxygen (lean), because the cell voltage grows with the oxygen difference across it.32

Myth An O2 sensor spacer fixes a catalyst code.

Fact A spacer only moves the downstream sensor out of the main gas flow so it sees a damped signal. It hides a catalyst problem instead of fixing it, and on a road vehicle that can count as tampering.Medium26

Myth Any O2 sensor works if the plug fits.

Fact Element type, heater power and response differ, and Bosch notes finger sensors must be replaced with the same type. Narrowband and wideband sensors are not interchangeable.34

Frequently asked

What does an O2 sensor do?

It measures leftover oxygen in the exhaust so the ECU can tell whether the engine runs rich or lean. The upstream sensor drives closed-loop fuel trim to hold the mixture near stoichiometric, and the downstream sensor checks that the catalytic converter is still storing oxygen and cleaning the exhaust.32

What are the symptoms of a bad O2 sensor?

A check engine light is the most common sign, often with heater-circuit, slow-response or catalyst efficiency codes. Drivers may also notice worse fuel economy, rough idle, a rich smell or a failed emissions test. Exhaust leaks and fuel problems cause similar symptoms, so check them first.Medium25

How long do oxygen sensors last?

Heated zirconia sensors commonly last around 100,000 miles (160,000 km), while older unheated sensors lasted about 30,000 to 50,000 miles. Contamination from silicone, coolant, oil burning or leaded fuel shortens life sharply, so an early failure often points to another engine problem.Medium2

What is the difference between upstream and downstream O2 sensors?

The upstream sensor sits before the catalytic converter and controls fueling. The downstream sensor sits after it and checks the converter: a healthy catalyst smooths out oxygen swings, so the downstream signal stays fairly steady. Many newer cars use a wideband sensor upstream and a narrowband downstream.Medium32

Is a lambda sensor the same as an O2 sensor?

Yes. Lambda sensor is the usual European term and O2 or oxygen sensor the usual US term for the same exhaust oxygen sensor. Lambda is the actual air-fuel ratio divided by the stoichiometric ratio, and the sensor helps the ECU hold it at 1.0.32

Wiring, pinouts and parts

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. Oxygen sensor · Wikipedia · reference · retrieved 2026-10-27
  3. Lambda sensors: precisely measuring for an optimized combustion (workshop brochure, 2023) · Bosch Automotive Aftermarket · vendor-doc · retrieved 2026-10-27
  4. Lambda Sensor LSU 4.9 data sheet 69034379 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  5. 40 CFR 86.1806-05: On-board diagnostics · US Electronic Code of Federal Regulations · standard · retrieved 2026-10-27
  6. Tampering and Aftermarket Defeat Devices enforcement alert (December 2020) · U.S. Environmental Protection Agency · oem · retrieved 2026-10-27