Robert Bosch GmbH

Bosch LSU 4.9 wideband sensor connector

LSU 4.9 harness plugLSU 4.9 mating connector1 987 280 016D261.205.356-016-pin LSU 4.9 plug

The Bosch LSU 4.9 connector is the 6-pin sealed harness plug that mates with the plug on the LSU 4.9 wideband lambda sensor. Bosch's installation spec 1 928 A00 17M-E describes a housing with MCP 1.5K flat contacts, single wire seals, a radial seal and a two-position secondary latch. Pins 1-6 carry pump current, virtual ground, heater minus, heater plus, trim resistor and Nernst voltage.12

At a glance

Positions6Sourced12
ContactsMCP 1.5K flat contactsQKKSourced1
Contact part numbers and wire rangeListed on Bosch offer drawing 1 928 A00 039The installation spec defers to offer drawing 1 928 A00 039 for the contact part numbers. We did not have that drawing, so the exact contact numbers and wire range are not confirmed here.Researched, unverified1
Sealing

Individual conductor seal per wire plus a radial seal to the mating plug

Sourced1
Secondary latch
  • Pre-latched as delivered
  • Push to end position with ≤ 30 N
Sourced1
Connector temperature< 140 °C at the sensor connector284 °FSourced2
Mating plug (automotive)

D261.205.356-01 for the sensor's automotive connector 1928.404.687

Sourced23
Mating plug (motorsport)AS007-35SN for the motorsport variant's AS607-35PNSourced23
Kit1 987 280 016: housing, terminals and sealsSourced · medium4

What the LSU 4.9 connector is

The LSU 4.9 is Bosch's planar wideband lambda sensor.

It ships with a pigtail ending in a 6-pin plug, and that plug carries a trimming resistor that sets the sensor's characteristic. The Bosch LSU 4.9 connector on this page is the harness half that mates with it.2

Bosch offers the sensor with two plug types. The automotive version has connector 1928.404.687 and mates with D261.205.356-01. The motorsport version has a DEUTSCH AS607-35PN and mates with an AS007-35SN.23

LSU 4.9 connector pinout

Bosch publishes the same pin functions for both plug types.

Heater supply
  • 7.5 V nominal at H+
  • System supply 10.8-16.5 V
  • 7.5 W steady state
Sourced2
Nernst cell
  • 300 Ω nominal
  • 250 µA maximum current load
Sourced2
Bosch LSU 4.9 pin assignment (Bosch Motorsport datasheet)23
PinBosch labelFunction
1APE / IPPump current
2IPN / VMVirtual ground
3H- / Uh-Heater negative
4H+ / Uh+Heater positive
5RT / IATrim resistor
6UN / RENernst voltage

Only the pump current IP correlates with oxygen content; the lambda voltage you see on a controller is the output of its evaluation circuit, not of the sensor.2

Harness plug parts and chamber layout

Bosch's installation spec 1 928 A00 17M-E lists five parts in the as-delivered plug, built to offer drawing 1 928 A00 039.

6-pin LSU 4.9 harness plug, as delivered (Bosch 1 928 A00 17M-E)1
ItemPartRole
1Plug housingHolds six chambers; primary latch springs engage each contact on both sides
2Secondary latchSlides from pre-latched to end position to lock all contacts
3Flat contact MCP 1.5K (QKK)Crimped per the contact maker's handling spec
4Individual conductor sealSeals each wire where it enters the housing
5Radial sealSeals the joint to the sensor plug
VariantCPA (premounted)Must not be moved or pressed during contact assembly

A later variant adds a pre-fitted connector position assurance (CPA) clip.1

The spec's end view numbers the chambers 1, 3, 5 across the top row and 2, 4, 6 across the bottom. The spec does not say in words whether that view is from the wire side, so confirm against the housing markings before pinning.Medium1

How to assemble and depin the plug

Crimp the contacts, then push each one straight into its chamber until the primary latch snaps in on both sides.

Unlatching tool part numberNot named in the installation spec1 928 A00 17M-E tells you to use 'the correct unlatching tool' but gives no part number. We found no maker page naming one.Researched, unverified

Check that the conductor seal sits correctly, then push the secondary latch from its pre-latched position to the end position with a blunt screwdriver in the slot.1

Bosch caps that push at 30 N (about 6.7 lbf). If the latch will not reach the end position at that force, a contact is not fully home; pull the latch back to pre-latched, reseat the contacts and try again.1

To remove a contact, move the latch back to pre-latched, insert the unlatching tool part way, push the contact toward the tool, then insert the tool fully and draw the wire out gently. Bosch says removed contacts must be replaced with new ones.1

Kits, variants and the LSU 4.2 trap

1 987 280 016 vs D261.205.356-01Relationship not confirmedBosch's datasheet names D261.205.356-01 as the automotive mating connector and the shop sells kit 1 987 280 016. No Bosch page we found states whether the kit contains that housing.Researched, unverified
LSU 4.2 compatibilityNot interchangeable, per retailersSeveral retailers warn that the LSU 4.2 6-pin plug differs from the LSU 4.9 plug. We found no Bosch page saying so; check the sensor generation before ordering.Researched, unverified

Bosch Motorsport's Australian shop lists 1 987 280 016 as a genuine Bosch 6-pin mating connector for all LSU 4.9 sensors, supplied with housing, terminals and seals. The same listing says it also fits some Bosch electronic throttle bodies.Medium4

Common mistakes

Cutting the sensor's own plug off loses the trim resistor, because Bosch places it in the sensor's connector module.

Keep the sensor plug and fit the matching harness plug instead.2

Mounting the plug where it gets too hot is the other one. Bosch limits the connector to under 140 °C (284 °F) and the sensor wire and sleeve to under 250 °C (482 °F), so route the pigtail away from the exhaust.2

CAD and drawings

No maker drawing or CAD link confirmed yet (TBC).

We link to the maker's own downloads and do not rehost drawings, 3D models or specifications: the makers' terms grant no redistribution. Our cavity maps are drawn from the cavity numbers, never traced from these drawings.

Crimp and assembly quick card

Strip lengthTBCNot published in the documents we could read; TBC.Researched, unverified
Crimp heightTBCNot published in the documents we could read; TBC.Researched, unverified
Pull-out force (minimum)TBCNot published in the documents we could read; TBC.Researched, unverified
Application specTBCBosch offer drawing 1 928 A00 039 (contact numbers) was not obtained. TE's MCP 1.5K contact 1418884-1 points to 114-18022 / 114-18022-20, but the -20 document we retrieved is an ultrasonic-welding guideline, not a crimp table.Researched, unverified

Summarised in our own words from the maker's application specifications and instruction sheets cited above. Disconnect the battery before working on a vehicle harness. A crimp is only as good as its pull test: check samples with your tool and wire before building a loom. Choosing a crimp tool →

Kit parts for this family

ItemPart numberDescriptionWireQtySource
TerminalMCP 1.5K SWS receptacle (TE family, e.g. 1418884-1 for 1.5 mm²)Reference only: TE MCP 1.5K sealed receptacle, 16 AWG, insulation 1.9-2.4 mmNot confirmed as the contact in the Bosch kit.1.5 mm²1 per wireUnverifiedLow5
Removal toolTBCUnlatching tool for MCP 1.5K in the LSU 4.9 plugNot published in the documents we could read; TBC.All1Unverified
Other1 987 280 016Bosch kit: housing, terminals and seals (no component list published)Component part numbers and quantities not published by the shop page.All1Medium4

Where it's used

Our harness designs

  • ECU2 harness (concept) Design, pre-releaseWideband: Bosch LSU 4.9 6-pin harness plug that mates the sensor directly. For the ECU2.6

Sensors that mate with it

Factory (OEM) use

No factory ECU in our pinout library uses this connector family.

Frequently asked

What is the Bosch LSU 4.9 connector pinout?

Bosch numbers the six pins as: 1 pump current (IP), 2 virtual ground (IPN or VM), 3 heater negative (H-), 4 heater positive (H+), 5 trim resistor (RT or IA) and 6 Nernst voltage (UN or RE). The same assignment applies to the automotive plug and to the DEUTSCH AS motorsport plug, per Bosch's datasheet.2

What connector mates with the Bosch LSU 4.9?

For the sensor with Bosch's automotive connector 1928.404.687, the datasheet lists mating connector D261.205.356-01. For the motorsport version with an AS607-35PN, it lists the DEUTSCH AS007-35SN. Bosch Motorsport's shop also sells kit 1 987 280 016 as the 6-pin mating connector with terminals and seals.24

Can I cut the plug off an LSU 4.9 sensor?

Not if you want correct readings. Bosch puts the trimming resistor, which sets the sensor's characteristic, in the sensor's connector module. Cutting off that plug removes it. Keep the sensor's plug and fit the matching harness plug, or use an extension built with the correct mating connector.2

How do I fit the secondary latch on the LSU 4.9 harness plug?

Insert all six contacts first. Then push the secondary latch from its pre-latched position to the end position with a blunt screwdriver, using no more than 30 N. If it will not snap home at that force, a contact is not fully seated. Pull the latch back, reseat the contacts and try again.1

How hot can the LSU 4.9 connector get?

Bosch's datasheet limits the connector to under 140 °C (284 °F). The sensor wire and protective sleeve can take under 250 °C (482 °F), and the sensor hex under 600 °C. Route the pigtail so the plug sits away from exhaust heat, ideally clipped to cooler structure.2

Keep going

Related

Sources

  1. Installation specification 1 928 A00 17M-E: cable harness plug 6-pin for LSU 4.9 (rev 03) · Robert Bosch GmbH · vendor-doc · retrieved 2026-10-27
  2. Lambda Sensor LSU 4.9 datasheet · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  3. Lambda Sensor LSU 4.9 product page · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  4. Mating connector, 6-pin for LSU 4.9 (1 987 280 016) · Bosch Motorsport Shop Australia · vendor-doc · retrieved 2026-10-27
  5. 1418884-1 AMP MCP 1.5K receptacle contact (product page) · TE Connectivity · vendor-doc · retrieved 2026-10-28
  6. internal GAINS internal: GAINS universal harness designs v1: Single Controller and IO Module harness build scripts, connector lists and wire lists (pre-release, not yet built)

Facts come from manufacturer documents and distributor spec pages, read on the retrieval date shown. Part numbers and ratings change: confirm against the maker's current drawing before you order. Manufacturer names identify parts only; no affiliation is implied.