Bosch · Wideband pump cell (needs controller)

Bosch LSU 4.9 wideband lambda sensor

Bosch 0 258 017 025Bosch Motorsport B261.209.358-03Bosch (BMW N54/N55 OE) 0 258 017 102

The Bosch LSU 4.9 is a planar dual-cell wideband lambda sensor that reads lambda 0.65 to air. It outputs pump current, not voltage, so it needs a controller. The six-pin connector carries pump current, virtual ground, heater minus and plus, a trim resistor and the Nernst voltage. Heater: 7.5 V nominal, 7.5 W steady state.1

Key specifications

Measures: Oxygen content of exhaust gas (lambda), from rich 0.65 to free air. Output: Wideband pump cell (needs controller).

Lambda range0.65to ∞airSourced1
Fuel compatibilityGasoline, diesel, E85Sourced1
Exhaust gas temperature
  • < 930 °C operating
  • < 1,030 °C short time
Sourced1
Hexagon temperature< 600°CSourced1
Exhaust gas pressure≤ 2.5 barhigher with reduced accuracySourced1
Heater
  • 7.5 V nominal H+
  • 7.5 W steady state
  • Control frequency ≥ 100 Hz
Sourced1
System supply10.8 to 16.5VSourced1
Nernst cell
  • 300 Ω nominal
  • Max current load 250 µA
Sourced1
Accuracy
  • Λ 0.80 ± 0.01
  • Λ 1.016 ± 0.007
  • Λ 1.70 ± 0.05
Sourced1
Thread and torqueM18x1.5, 22 mm hex, 40-60 N·mSourced1
Wire length
  • 95 cmautomotive connector
  • 20-90 cmmotorsport connector
Sourced1
Connector temperature< 140°Cwire and sleeve < 250 °CSourced1
Part numberMakerNote
0 258 017 025BoschWith automotive connector 1 928 404 6871
B261.209.358-03Bosch MotorsportWith motorsport connector AS607-35PN1
0 258 017 102Bosch (BMW N54/N55 OE)LSU 4.9 variant with a vehicle connector (BMW 11787558087)Medium2

Pinout and connector

123456Schematic, pin-number order (positions not published)
Schematic in pin-number order: the maker does not publish cavity positions. Mating face labels. Pin functions from the maker's document. Our drawing from the published pin list, not a maker drawing.
  • Supply
  • Ground / return
  • Signal
  • Shield
  • Not used / not listed
Download pinout (SVG)
PinFunction (as published)Typical ECU inputWire note
1Pump current (IP / APE)Wideband controller (match the pin name)—
2Virtual ground (VM / IPN)Wideband controller (match the pin name)Return to sensor ground, not chassis
3Heater minus (H− / Uh−)Wideband controller (match the pin name)Return to sensor ground, not chassis
4Heater plus (H+ / Uh+)Wideband controller (match the pin name)—
5Trim resistor (RT / IA)Wideband controller (match the pin name)—
6Nernst voltage (UN / RE)Wideband controller (match the pin name)—

Bosch's data sheet gives pin functions but no wire colours; identify wires at the connector.1 The ECU-input and wire columns are our general guidance, not the maker's.

Connector: Bosch 1 928 404 687 (automotive) or AS607-35PN (motorsport); mating part D261.205.356-01 (automotive) / AS007-35SN (motorsport)1 Connector library

Terminals and seals: Not listed: the Bosch data sheet gives the mating housing only, not contact or seal part numbers.

Transfer function and calibration data

Pump current vs lambda1
0.653.0175.3857.75210.12-2-0.93750.1251.1882.25Pump current IP (mA)Lambda (λ)

Bosch notes only IP correlates with oxygen content; the UA voltages in its table are outputs of an evaluation circuit, not the sensor.

Show the 24 data points
Pump current IP (mA)Lambda (λ)
-20.65
-1.6020.7
-1.2430.75
-0.9270.8
-0.80.822
-0.6520.85
-0.4050.9
-0.1830.95
-0.1060.97
-0.040.99
01.003
0.0151.01
0.0971.05
0.1931.1
0.251.132
0.3291.179
0.6711.429
0.9381.701
1.151.99
1.3852.434
1.73.413
25.391
2.157.506
2.2510.12

How it's calibrated

ECU-neutral: enter these values in whichever ECU you use. Nominal values without the maker's tolerance band.

Transfer function

  • Lambda from Pump current IP (maker table)1

Worked conversion

  • A pump current of 0.193 mA is λ 1.1, which is 16.2:1 on gasoline (λ × 14.7). Pump current is read by a wideband controller, not by a plain analog input.1Calculated from the maker's data
Pump current vs lambda (24 rows)Calculated from the maker's data
Pump current IP (mA)Lambda (λ)AFR (gasoline, 14.7:1)
-20.659.55
-1.6020.710.29
-1.2430.7511.02
-0.9270.811.76
-0.80.82212.08
-0.6520.8512.49
-0.4050.913.23
-0.1830.9513.96
-0.1060.9714.26
-0.040.9914.55
01.00314.74
0.0151.0114.85
0.0971.0515.44
0.1931.116.17
0.251.13216.64
0.3291.17917.33
0.6711.42921.01
0.9381.70125
1.151.9929.25
1.3852.43435.78
1.73.41350.17
25.39179.25
2.157.506110.34
2.2510.119148.75

AFR (gasoline, 14.7:1) calculated by us from the maker's values.

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptPreset listedOnboard LSU 4.9 controller: Nernst pin 23, pump 24, virtual ground 25, heater minus 27, trim 26. Concept hardware, not yet bench-tested.Medium3
Haltech (Elite / Nexus)Preset listedNexus onboard wideband supports LSU 4.9; Haltech sells an LSU 4.9 kit for it (HT-010740). The Elite 2500 has no onboard controller: use an external CAN controller.Medium789
Link (G4X)Preset listedOnboard digital wideband on the G4X FuryX; Link sells an LSU 4.9 for ECUs with onboard wideband.Medium1011
MoTeC (M1)Preset listedThrough MoTeC's LTC lambda-to-CAN module (the M150 has no onboard wideband).Medium121314
ECUMaster (EMU Black)Preset listedBuilt-in wideband input; ECUMaster names LSU 4.2 and LSU 4.9.15
AEM (Infinity)UnverifiedAEM's public documents name LSU 4.2 only.No public source
MaxxECUPreset listedBuilt-in wideband supports LSU 4.9; MaxxECU sells Bosch 0 258 017 025.1617
Holley (Terminator X / EFI)Preset listedTerminator X controls an LSU 4.9 supplied by Holley (Holley P/N 554-155). Holley says its sensors are calibrated for Holley EFI, so a generic LSU 4.9 is not stated as supported.Medium1819

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Wiring and installation

Mount where the exhaust is representative and hot but within limits, wire upward and as vertical as possible, away from the tailpipe and with no leaks upstream. Use only the recommended thread grease; never paint the sensor.1

Do not heat the sensor while water can still condense in a cold exhaust; Bosch requires protection against condensation water.1

Failure modes and checks

Reading lean on a rich engine

Likely cause Air leak upstream of the sensor

Check Inspect joints; Bosch requires a leak-free passage opposite the sensor.Medium1

Offset reading across the range

Likely cause Trim resistor (pin 5) not connected or controller set for another sensor

Check Measure the trim resistor in the connector and confirm the controller sensor type.Medium1

Sensor dies early

Likely cause Thermal shock from condensation or overheating above 930 °C

Check Delay heater start until the exhaust is dry and check gas temperature at the mounting point.Medium1

Frequently asked

What is the pinout of the Bosch LSU 4.9?

Pin 1 pump current (IP), pin 2 virtual ground (VM), pin 3 heater minus, pin 4 heater plus, pin 5 trim resistor, pin 6 Nernst voltage (UN), per Bosch Motorsport's data sheet.1

What heater voltage does the LSU 4.9 need?

7.5 V nominal on H+, with 7.5 W steady-state heater power and PWM control at 100 Hz or more, from a 10.8-16.5 V system supply. The controller regulates it; never connect the heater straight to battery voltage.1

Is the LSU 4.9 compatible with E85?

Yes. Bosch lists gasoline, diesel and E85 as compatible fuels. Lambda readings stay valid; only the AFR scale changes with fuel.1

Related

Use it with GAINS

Bosch LSU 4.9 wideband lambda sensor on GAINS hardware

ECU2WB onboard front end

Pins
On the ECU2 pin map
Pull-up
Not used
Shielding
Not needed

Sensor pin 6 (UN) to ECU 23, pin 1 (IP) to 24, pin 2 (VM) to 25, pin 5 (trim) to 26, pin 3 (H−) to 27. Heater plus (sensor pin 4) to a fused, switched 12 V feed.Medium3

ECU2Pin 26 shared as AVI6

Pins
On the ECU2 pin map
Pull-up
Not used
Shielding
Not needed

If pin 26 is reassigned to AVI6, the wideband runs on a nominal calibration whose accuracy is still to be bench-quantified.Medium3

The onboard wideband is designed for the LSU 4.9 from Bosch's published documents and needs bench validation against a reference lambda meter before any accuracy claim.3

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.34

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

19 sources
  1. Lambda Sensor LSU 4.9 data sheet 69034379 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  2. cross reference: Superspares AU Bosch fitment by engine code (N54 LSU 4.9 0258017102; M113 knock 0261231110; M113 LSF4.2 025800 · superspares.com.au · vendor-doc · retrieved 2026-10-25
  3. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  4. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  5. LSU 4 9 product page · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  6. Nexus R3 VCU (HT-193000) product page · Haltech · vendor-doc · retrieved 2026-10-27
  7. Onboard Wideband Bosch LSU 4.9 Sensor Kit (HT-010740) · Haltech · vendor-doc · retrieved 2026-10-27
  8. Elite 2500 ECU (HT-151300) product page · Haltech · vendor-doc · retrieved 2026-10-27
  9. LTC (Lambda to CAN) product page · MoTeC · vendor-doc · retrieved 2026-10-27
  10. Bosch LSU 4.9 product page (#57006) · MoTeC · vendor-doc · retrieved 2026-10-27
  11. M150 product page (M1 series) · MoTeC · vendor-doc · retrieved 2026-10-27
  12. EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-10-27
  13. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-10-27
  14. Lambda Sensor Bosch wideband LSU 4.9 store page · MaxxECU · vendor-doc · retrieved 2026-10-27
  15. Terminator X MPFI part numbers / install manual 199R11760 · Holley · vendor-doc · retrieved 2026-10-27
  16. HP / Dominator EFI wiring manual 199R10555 · Holley · vendor-doc · retrieved 2026-10-27