Bosch · Wideband pump cell (needs controller)

Bosch LSU 4.2 wideband lambda sensor

Bosch 0 258 007 057

The Bosch LSU 4.2 is the wideband lambda sensor generation before the LSU 4.9. It is still found on engines such as the VW/Audi 1.8T 20v (Bosch 0 258 007 057). Bosch's LT4 controller supports the LSU 4.2, LSU 4.9 and Mini-LSU 4.9, but the sensors are not interchangeable without changing the controller setting and connector.Medium34

Key specifications

Measures: Exhaust oxygen content (lambda). Output: Wideband pump cell (needs controller).

Supported controllersBosch LT4 supports LSU 4.2, LSU 4.9 and Mini-LSU 4.9Sourced3
Catalog fitmentVW/Audi 1.8T 20v upstream wideband (5-wire per listing)Low confidence4
Heater rating and pump-current tableUnverifiedBosch's LSU 4.2 data sheet was not retrievable from an official Bosch host for this draft.Researched, unverified
PinoutUnverifiedNot published here until an official Bosch LSU 4.2 document is archived.Researched, unverified
Part numberMakerNote
0 258 007 057BoschVW 1K0998262D; listed for the VW/Audi 1.8T 20vLow4

Pinout and connector

No pinout is shown: the maker or OEM does not publish one in a document we could cite. Identify pins with a meter before wiring.

Connector not published. Browse the connector library

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptTo be confirmedThe ECU2's onboard controller is specified for LSU 4.9; LSU 4.2 is not in the design documents.Medium5
Haltech (Elite / Nexus)UnverifiedHaltech's public pages name NTK and LSU 4.9 only.No public source
Link (G4X)UnverifiedLink's public pages do not name LSU 4.2.No public source
MoTeC (M1)UnverifiedMoTeC's public pages name LSU 4.9 only.No public source
ECUMaster (EMU Black)Preset listedBuilt-in wideband input; ECUMaster names LSU 4.2 and LSU 4.9.7
AEM (Infinity)Preset listedAEM's harness instructions say an LSU 4.2 can be connected directly (AEM sells it under its own part number).Medium8
MaxxECUPreset listedBuilt-in wideband supports LSU 4.2; MaxxECU sells Bosch 0 258 007 057.910
Holley (Terminator X / EFI)UnverifiedHolley's public documents name LSU 4.9 only.No public source

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

The maker does not publish a data sheet, drawing or CAD model for this part that we could find.

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Wiring and installation

Treat the LSU 4.2 as a different sensor from the 4.9: set the controller for the 4.2 and use its own connector. Mounting rules are the same as for any LSU sensor.Medium32

Failure modes and checks

Wrong readings after swapping in a 4.9

Likely cause Controller still set for LSU 4.2

Check Change the controller sensor type and re-pin to the 4.9 connector.Medium3

Slow response on an old sensor

Likely cause Aged element

Check Compare against a known-good sensor; replace if response lags.Low1

Frequently asked

Is the LSU 4.2 the same as the LSU 4.9?

No. They are different Bosch generations. Bosch's LT4 controller supports both, but it must be set for the sensor fitted.3

Can I replace an LSU 4.2 with an LSU 4.9?

Yes, if the controller supports the 4.9 and you change the connector and sensor setting. An ECU that only supports the 4.2 cannot read a 4.9 correctly.Medium3

Related

Use it with GAINS

Bosch LSU 4.2 wideband lambda sensor on GAINS hardware

ECU2AVI (external LSU 4.2 controller 0-5 V)

Pins
On the ECU2 pin map
Pull-up
Off
Shielding
Not needed

The onboard front end is designed for the LSU 4.9; use an external LSU 4.2 controller's analog output.Medium5

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.56

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

10 sources
  1. Lambda sensors: program and product details (workshop brochure) · Bosch Automotive Aftermarket · vendor-doc · retrieved 2026-10-27
  2. Lambda Sensor LSU 4.9 data sheet 69034379 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  3. Lambdatronic LT4 data sheet 75422859 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  4. part numbers: VAG retailer listings: 1.8T MAF 06A906461L/Bosch 0280218340, O2 1K0998262D/Bosch 0258007057 LSU4.2, EA888 Gen3 · fcpeuro.com · vendor-doc · retrieved 2026-10-25
  5. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  6. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  7. EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-10-27
  8. 30-3519 Infinity plug-and-play harness instructions · AEM Electronics · vendor-doc · retrieved 2026-10-27
  9. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-10-27
  10. Lambda Sensor Bosch wideband LSU 4.2 store page · MaxxECU · vendor-doc · retrieved 2026-10-27

Not yet indexed: fewer than 3 FAQs; more than 40% of specs unverified.