Bosch · Wideband pump cell (needs controller)

Bosch LSU ADV wideband lambda sensor

Bosch 0 258 027 010

The Bosch LSU ADV is a wideband lambda sensor with the LSU 4.9's 0.65-to-air range but higher temperature limits: hexagon 650 °C operating. It has no trim resistor, so only five of six pins are used, and Bosch states it works only with a special evaluation unit such as the LT4 ADV.2

Key specifications

Measures: Exhaust oxygen content (lambda) from 0.65 to free air. Output: Wideband pump cell (needs controller).

Lambda range0.65to ∞Sourced2
Hexagon temperature
  • ≤ 650 °C operating
  • ≤ 700 °C short time
Sourced2
Exhaust gas temperature
  • ≤ 930 °C operating
  • ≤ 1,030 °C short time
Sourced2
Heater
  • 7.5 V nominal
  • 8.7 W steady state
  • ≥ 100 Hz control
Sourced2
Nernst cell
  • 300 Ω nominal
  • Max current load ≤ 80 µA
Sourced2
Switch-on time≤ 5 sSourced2
Accuracy (pump current)
  • Λ 0.8: −0.652 ± 0.032 mA
  • Λ 1: −0.018 ± 0.008 mA
  • Λ 1.7: 0.515 ± 0.022 mA
Sourced2
ThreadM18x1.5, 22 mm, 40-60 N·mSourced2
Part numberMakerNote
0 258 027 010BoschWith automotive connector 1 928 404 6692

Pinout and connector

123456Schematic, pin-number order (positions not published)
Schematic in pin-number order: the maker does not publish cavity positions. Mating face labels. Pin functions from the maker's document. Our drawing from the published pin list, not a maker drawing.
  • Supply
  • Ground / return
  • Signal
  • Shield
  • Not used / not listed
Download pinout (SVG)
PinFunction (as published)Typical ECU inputWire note
1Pump current (IP / APE)Wideband controller (match the pin name)—
2Virtual ground (VM / IPN)Wideband controller (match the pin name)Return to sensor ground, not chassis
3Heater minus (Uh− / H−)Wideband controller (match the pin name)Return to sensor ground, not chassis
4Heater plus (Uh+ / H+)Wideband controller (match the pin name)—
5Not connectedLeave unconnected—
6Nernst voltage (UN / RE)Wideband controller (match the pin name)—

Pin functions as published.2 The ECU-input and wire columns are our general guidance, not the maker's.

Connector: Bosch 1 928 404 669 (automotive); mating part F02U.B00.725-012 Connector library

Terminals and seals: Not listed: the Bosch data sheet gives the mating housing only, not contact or seal part numbers.

Transfer function and calibration data

Pump current vs lambda2
0.651.7372.8253.9125-1.38-0.6850.010.7051.4Pump current IP (mA)Lambda (λ)

Different curve from the LSU 4.9: a controller calibrated for one sensor reads the other wrongly.

Show the 23 data points
Pump current IP (mA)Lambda (λ)
-1.380.65
-1.110.7
-0.880.75
-0.650.8
-0.4750.85
-0.370.88
-0.30.9
-0.160.95
-0.0760.98
-0.0480.99
-0.021
0.011671.03
0.032781.05
0.064441.08
0.085561.1
0.171.18
0.23081.26
0.361.43
0.40151.5
0.521.7
0.54741.78
0.772.43
1.45

How it's calibrated

ECU-neutral: enter these values in whichever ECU you use. Nominal values without the maker's tolerance band.

Transfer function

  • Lambda from Pump current IP (maker table)2

Worked conversion

  • A pump current of 0.06444 mA is λ 1.08, which is 15.9:1 on gasoline (λ × 14.7). Pump current is read by a wideband controller, not by a plain analog input.2Calculated from the maker's data
Pump current vs lambda (23 rows)Calculated from the maker's data
Pump current IP (mA)Lambda (λ)AFR (gasoline, 14.7:1)
-1.380.659.55
-1.110.710.29
-0.880.7511.02
-0.650.811.76
-0.4750.8512.49
-0.370.8812.94
-0.30.913.23
-0.160.9513.96
-0.0760.9814.41
-0.0480.9914.55
-0.02114.7
0.011671.0315.14
0.032781.0515.44
0.064441.0815.88
0.085561.116.17
0.171.1817.35
0.23081.2618.52
0.361.4321.02
0.401481.522.05
0.521.724.99
0.54741.7826.17
0.772.4335.72
1.4573.5

AFR (gasoline, 14.7:1) calculated by us from the maker's values.

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptTo be confirmedThe ECU2's onboard controller is specified for LSU 4.9; Bosch says the LSU ADV needs an ADV-type evaluation unit.Medium3
Haltech (Elite / Nexus)UnverifiedNo public statement on LSU ADV support found.No public source
Link (G4X)UnverifiedNo public statement on LSU ADV support found.No public source
MoTeC (M1)UnverifiedNo public statement on LSU ADV support found.No public source
ECUMaster (EMU Black)UnverifiedNo public statement on LSU ADV support found.No public source
AEM (Infinity)UnverifiedNo public statement on LSU ADV support found.No public source
MaxxECUUnverifiedNo public statement on LSU ADV support found.No public source
Holley (Terminator X / EFI)UnverifiedNo public statement on LSU ADV support found.No public source

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Wiring and installation

Same installation rules as the LSU 4.9: representative hot exhaust, wire upward, no leaks upstream, no paint or wax on the sensor.Medium21

Failure modes and checks

Wrong lambda on an LSU 4.9 controller

Likely cause ADV pump-current curve and missing trim resistor differ from the 4.9

Check Use an ADV-capable evaluation unit such as Bosch's LT4 ADV.Medium2

Cracked element after cold starts

Likely cause Condensation shock

Check Delay heating until the exhaust is dry.Medium21

Frequently asked

What is the difference between the LSU ADV and LSU 4.9?

The ADV tolerates higher hexagon temperatures (650 °C against 600 °C), draws a bit more heater power (8.7 W against 7.5 W), has no trim resistor and uses a different pump-current curve, so it needs an ADV-specific controller.21

Can an LSU 4.9 controller run an LSU ADV?

Not correctly. Bosch states the ADV operates only with a special evaluation unit such as the LT4 ADV, and its pump-current curve differs from the 4.9.2

Related

Use it with GAINS

Bosch LSU ADV wideband lambda sensor on GAINS hardware

ECU2AVI (external ADV controller 0-5 V)

Pins
On the ECU2 pin map
Pull-up
Off
Shielding
Not needed

The onboard front end targets the LSU 4.9 only. Read an ADV-capable controller's analog output on an AVI.Medium3

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.34

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

  1. Lambda Sensor LSU 4.9 data sheet 69034379 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  2. Lambda Sensor LSU ADV data sheet 69086859 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  3. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  4. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  5. LSU ADV product page · Bosch Motorsport · vendor-doc · retrieved 2026-10-27

Not yet indexed: fewer than 3 FAQs.