Wiring guide

Shielded cable termination: drain wires, grounding one end and sensor shields

Shielded cable termination means connecting the shield or drain wire so it drains noise without carrying current. For low-frequency sensor signals the usual rule is a single ground point: tie the drain to the ECU's sensor ground or shield pin and leave the far end insulated, so no ground-loop current flows in the shield. Above roughly 1 MHz, and for some data links, shields are bonded at both ends with low-impedance 360° connections.Medium675

Key takeaways

  • Ground a low-frequency signal shield at one point, normally the ECU end; insulate the far end.
  • Two ground points with a voltage between them drive current along the shield, a ground loop.
  • High-frequency shields work best bonded at both ends with short, 360° connections.
  • Foil gives 100% coverage and needs a drain wire; braid is easier to terminate and lower in resistance.
  • Keep the unshielded tail at each end as short as possible.

Foil and drain vs braid

Foil shields are an aluminium-polyester tape with full coverage.

Shield constructions (Belden datasheets)21
CableShieldCoverageDrain
Belden 8723Foil per pair (aluminium + polyester)100%24 AWG tinned copper, one per pair
Belden 8103Overall foil + tinned copper braid100% foil, 65% braid24 AWG tinned copper

The foil is too thin to crimp, so a bare drain wire runs in contact with it and becomes the connection point; Belden's 8723 pairs each have 100% foil with a 24 AWG tinned drain.2

Braid is woven copper with partial coverage, but you can terminate it directly. Many instrument cables combine both: Belden 8103 has 100% foil plus a 65% tinned copper braid and a drain wire.1

Why low-frequency shields are grounded at one end

Ground at two places that sit at different voltages and current flows along the shield between them.

TI's CAN note puts it simply: ground the network at a single point so parasitic currents cannot flow in the shield.6

For electric-field noise below about 1 MHz, a single ground point is enough; Wikipedia cites Analog Devices for that threshold. Most engine sensor signals are well below it.Medium7

When both ends are grounded

At high frequency, magnetic coupling dominates and the shield must carry a return current to cancel it.

Single vs double ended
  • Single point below about 1 MHz
  • Both ends above, with 360° bonds
Sourced · medium7
Pigtail penalty

More than 35 dB worse than 360° termination above a few MHz (NASA test, as cited)

Sourced · medium7

Howard Johnson's view for fast digital links is a low-impedance shield bond at both ends, and he rejects the series resistor trick because it makes the shield useless at high frequency.5

How the bond is made matters too. A NASA test cited on Wikipedia found pigtail terminations more than 35 dB worse than 360° terminations above a few MHz.Medium7

CAN bus shields

Cable
  • 120 Ω characteristic impedance twisted pair
  • Shielded cable recommended in electrically harsh environments
Sourced6
J1939-11 shield grounding detailDefined in the recommended practiceWe could not read the J1939-11 text; its exact shield and capacitive-ground requirements are not reproduced here.Researched, unverified

SAE J1939-11 defines a 250 kbit/s physical layer on twisted shielded pair for harsh vehicle environments, using ISO 11898-2 high-speed transceivers. Many passenger-car and motorsport CAN links use unshielded twisted pair instead.46

If you use a shield, TI recommends a short pigtail crimped to the shield at each connector, brought through its own pin to a nearby ground pin, with the whole network grounded at a single point at the source.6

Knock, crank and cam sensors

KS4-R2 connector
  • 3 pins: 1 signal, 2 ground, 3 screen
  • 0.5 mm² wire
  • Elastomer sleeve
Sourced3
Sensor-end shield termination for KS4-R2Described in Bosch's offer drawingThe Bosch product page labels pin 3 as screen but does not say how to terminate it; the offer drawing was not read.Researched, unverified
OEM practice for VR crank and cam sensor shieldsVaries by vehicle makerWe did not find a sensor maker or OEM training document on a public page that states the termination rule for VR sensor shields.Researched, unverified

Knock sensors and variable reluctance (VR) crank and cam sensors put out small AC signals, which makes them the usual candidates for shielded twisted pair. Bosch Motorsport's KS4-R2 knock sensor gives the screen its own connector pin (pin 3, Scr) next to signal and ground.3

Run the drain back to the ECU and land it on the sensor ground or shield pin the ECU maker designates. Leave it cut back and insulated at the sensor unless the sensor maker's drawing says otherwise.Medium63

How to terminate a shield

Strip the jacket back only as far as needed, fold the braid or foil back, and twist the drain out.

Termination checklistMedium671
StepECU endSensor end
Drain wireCrimp into its own contact; to shield or sensor ground pinCut back and insulate
Foil / braidFold back, cover with heat shrinkFold back, cover with heat shrink
Unshielded tailAs short as possibleAs short as possible
PairsKeep twisted to the contactsKeep twisted to the contacts

Cover the exposed shield with heat shrink so it cannot touch a pin or the housing.Medium61

At the ECU end, crimp the drain into its own contact and route it to the shield or sensor ground pin. At the far end, cut the drain short, fold it back and insulate it. Keep the unshielded tail at both ends short.Medium67

Common mistakes

Grounding the drain at both ends on a low-frequency sensor line creates the ground loop the shield was meant to avoid.

Landing it on chassis at one end and sensor ground at the other is the same mistake.Medium6

Long pigtails and shields that stop several centimetres short of the connector let noise in where the shield ends. Using the shield as the signal return also defeats it, since the signal then shares a conductor with the noise current.Medium75

Frequently asked

Should a cable shield be grounded at both ends?

For low-frequency sensor signals, usually no: ground the shield at one point so no ground-loop current flows in it, as TI recommends for CAN networks. Above roughly 1 MHz the advice reverses, and shields are bonded at both ends with short 360° connections so they can cancel magnetic fields.Medium67

Which end of a shielded cable should be grounded?

Ground the end where the signal is measured, normally the ECU, and leave the sensor end insulated. That keeps the single ground at the controller's sensor ground or shield pin, which is the reference the input is measured against. Follow the ECU or sensor maker's pinout if it names a shield pin.Medium63

What do you do with the drain wire at the sensor end?

Cut it back, fold it against the jacket and cover it with heat shrink so it cannot touch a pin, the housing or the engine. Do not connect it to the sensor ground or the sensor body unless the sensor maker's drawing calls for it, since that adds a second ground point.Medium6

Does CAN bus need shielded cable?

Not always. SAE J1939-11 specifies twisted shielded pair for harsh truck and off-road environments, but many CAN links use unshielded 120 Ω twisted pair. TI recommends shielded cable where the electrical environment is harsh, with the shield grounded at a single point at the source.46

Should a knock sensor use shielded wire?

Shielded wire is common practice for knock sensors because their signal is small and AC. Bosch Motorsport's KS4-R2 has a dedicated screen pin next to signal and ground. Ground that screen at the ECU end only and keep the pair twisted, unless the sensor maker's drawing specifies otherwise.Medium36

Keep going

Related

Sources

  1. 8103 technical data sheet (overall Beldfoil plus braid, drain wire) · Belden · vendor-doc · retrieved 2026-10-27
  2. 8723 technical data sheet (individually foil-shielded pairs, drain wire) · Belden · vendor-doc · retrieved 2026-10-27
  3. Knock sensor KS4-R2 product page · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  4. J1939-11_202607 Physical layer, 250 kbit/s, twisted shielded pair (abstract) · SAE International · standard · retrieved 2026-10-27
  5. Cable shield grounding, High-Speed Digital Design newsletter vol. 2 issue 2 (H. Johnson) · Signal Consulting · reference · retrieved 2026-10-27
  6. SLLA270 Controller Area Network physical layer requirements (S. Corrigan, January 2008) · Texas Instruments · vendor-doc · retrieved 2026-10-27
  7. Shielded cable (section on grounding, citing Analog Devices MT-095 and a NASA pigtail study) · Wikipedia · reference · retrieved 2026-10-27

Facts come from manufacturer documents and distributor spec pages, read on the retrieval date shown. Part numbers and ratings change: confirm against the maker's current drawing before you order. Manufacturer names identify parts only; no affiliation is implied.