TE Connectivity (Deutsch)

Deutsch DTM connectors

DTM seriesDeutsch DTM connectorDTM04 / DTM06

A Deutsch DTM connector is TE's small sealed wire-to-wire connector built around size 20 contacts. It comes in 2, 3, 4, 6, 8 and 12-way housings, carries 7.5 A per contact and runs from -55 to 125 °C. Receptacles (DTM04) take pins, plugs (DTM06) take sockets, and a separate wedge lock holds the contacts.14

At a glance

Contact size
  • Size 20
  • 1.0 mm pin0.04 in
Sourced12
Current7.5A per contactSourced12
Layouts2, 3, 4, 6, 8 and 12 waySourced1
Wire range16-22 AWG with standard contacts1.5-0.35 mm²TE's DTM FAQ quotes 14-22 AWG (2.50-0.35 mm²) for the series, but the TE contact pages found stop at 16 AWG. The drawings list 16-20 AWG as reference only.Conflict16121
Insulation OD1.35-3.05mm0.053-0.120 inSourced24
Temperature-55 to 125°C-67 to 257 °FSourced1
Sealing
  • IP68 and IP6K9K
  • Silicone grommet and interfacial seal
Sourced12
Operating voltage250V AC/DCSourced2
Vibration20 G, 10-2000 Hz, no discontinuity over 1 µsSourced1
Mating cycles100 with no electrical or mechanical defectsSourced1

Part numbers

What a Deutsch DTM connector is

The Deutsch DTM connector is the smallest of the three common Deutsch rectangular families.

It uses size 20 contacts where DT uses size 16, so it suits sensor, signal and light-load circuits on 20-16 AWG wire.123

Every DTM pair is a DTM04 receptacle with pins and a DTM06 plug with sockets. The housings are glass-filled thermoplastic with silicone seals, and a separate wedge lock in each half holds the contacts in place.16

Common DTM housings and their wedges

Order each housing with its own wedge.

Pages in this library. Dimensions from TE drawings; DTM04-6P from TE's product page.56738
PartTypeWaysMates withWedgeSize L x W x H
DTM04-4PReceptacle (pins)4DTM06-4SWM-4P43.69 x 19.20 x 19.61 mm
DTM06-4SPlug (sockets)4DTM04-4PWM-4S30.10 x 15.24 x 17.65 mm
DTM04-6PReceptacle (pins)6DTM06-6SWM-6P44.9 x 23.8 x 19.2 mm (TE page)
DTM06-6SPlug (sockets)6DTM04-6PWM-6S30.10 x 15.24 x 20.75 mm

Receptacle wedges end in P and plug wedges end in S.57

DTM contacts and tools

All DTM contacts are size 20 and rated 7.5 A typical.

Crimp tool, solidHDT-48-00sizes 12, 16, 20; four-indentSourced20
Crimp tool, stampedDTT-20-00size 20TE confirms a size 20 tool, now superseded, but its page does not state the contact style. Distributors sell it for stamped and formed contacts.Sourced · medium21
Removal tool0411-240-2005size 20Sourced · medium22
Size 20 contacts from TE product pages. All 7.5 A typical.9101112131415161718
PinSocketStyleWirePlating
0460-202-201410462-201-20141Solid20 AWG (0.5 mm²)Nickel
0460-010-201410462-005-20141Solid16-18 AWG (0.75-1.5 mm²)Nickel
0460-202-20310462-201-2031Solid20 AWG (0.5 mm²)Gold
1060-20-01221062-20-0122Stamped16-22 AWG (0.35-1.5 mm²)Nickel
1060-20-01441062-20-0144Stamped16-22 AWG (0.35-1.5 mm²)Gold interface, tin crimp

Solid contacts cover one wire range per part number and take a closed-barrel indent crimp. Stamped contacts cover 16-22 AWG and take an open-barrel F-crimp.916

Gold versions suit low-current sensor signals. TE lists the solid gold contacts at -55 to 150 °C, above the 125 °C housing rating.Medium1413

How to assemble a DTM connector

Strip to the depth the contact needs, crimp with the matching tool, then push the contact in from the wire side until it clicks.

Do this for every cavity before touching the wedge.Medium620

Press the wedge in from the mating face. It only seats when all contacts are home, so a wedge that stops short is a fault check, not something to force.Medium61

Fill unused cavities with a size 20 sealing plug. Check that wire insulation sits inside 1.35-3.05 mm, or the grommet will not seal.Medium219

Where DTM connectors are used

TE lists truck, bus, off-highway, agriculture, marine and motorcycle uses.

Typical spots are on the engine or transmission, under the hood, at solenoids and motor controllers, and along the chassis or in the cab.1

Common mistakes

Crimping a solid contact in an open-barrel tool, or a stamped contact in an indent tool, gives a crimp that may pass a tug test and fail later. Match the tool to the contact style.Medium2016

Running a DTM circuit above 7.5 A overheats the contact. Use a size 16 DT or larger contact for heavier loads instead.1

Leaving a cavity empty without a plug breaks the IP68 seal even if every wire is sealed.Medium41

CAD and drawings

  • Application specApplication specification 114-151010 rev D2 (DTM connector system) · 114-15101024Download from TE Connectivity ↗No login at last check; the maker may change this
  • Product specProduct specification 108-151010 rev F (DTM series) · 108-15101025Download from TE Connectivity ↗Registration may be needed
  • Application specApplication specification 114-151003 rev J1 (size 20 stamped and formed contacts) · 114-15100326Download from TE Connectivity ↗No login at last check; the maker may change this
  • Application specApplication specification 114-151004 rev E1 (size 4-20 solid contacts) · 114-15100427Download from TE Connectivity ↗No login at last check; the maker may change this
  • Instruction sheetInstruction sheet 0425-071-0000 rev D (HDT-48-00 crimp tool) · 0425-071-000028Download from TE Connectivity ↗No login at last check; the maker may change this
  • Instruction sheetInstruction guide 0425-072-0000 rev A (DTT-20-00 stamped-contact crimp tool, superseded) · 0425-072-000029Download from TE Connectivity ↗No login at last check; the maker may change this
  • Instruction sheetInstruction sheet 408-151008 rev B (DT-RT1 removal tool) · 408-15100830Download from TE Connectivity ↗No login at last check; the maker may change this

We link to the maker's own downloads and do not rehost drawings, 3D models or specifications: the makers' terms grant no redistribution. Our cavity maps are drawn from the cavity numbers, never traced from these drawings.

Crimp and assembly quick card

Strip length

Solid size 20 (0460-202-20141, 0462-201-20141, 0460-010-20141, 0462-005-20141): 3.96-5.54 mm (0.156-0.218 in). Stamped size 20 (1060/1062-20-01xx): 4.45 +/- 0.64 mm (0.175 +/- 0.025 in) per the DTT-20-00 guide.

114-151003 gives the stamped strip length only in a figure that could not be extracted; the legacy 2009 Deutsch manual gives 3.81-5.08 mm, consistent with the DTT-20-00 guide.Sourced272829
Crimp height
  • Stamped 1060/1062-20-01xx and 1062-20-03 (wire barrel): 16 AWG 1.22-1.30 mm
  • 18 AWG 1.19-1.27 mm
  • 20 AWG 0.94-1.02 mm
  • 22 AWG 0.89-0.97 mm
  • Crimp width 1.80-1.98 mm (insulation OD 1.91-3.18 mm). Solid contacts on HDT-48-00 (reference only, validate by pull test): 0460-202-20/0462-201-20 at 20 AWG 0.73-0.82 mm lock indent, 0.95-1.02 mm entry indent
  • 0460-010-20/0462-005-20 at 16 AWG 0.90-0.98 / 1.06-1.22 mm, at 18 AWG 0.79-0.90 / 1.03-1.10 mm.
Sourced2627
Pull-out force (minimum)
  • Stamped size 20: 14-18 AWG 89 N20 lbf
  • 20 AWG 67 N15 lbf
  • 22 AWG 22 N. Solid size 20: 89 N at 16, 18 and 20 AWG per 114-151004 rev E15 lbf · 20 lbf
  • 108-151004 rev E gives 156 N at 16 AWG, 111 N at 18 AWG and 67 N at 20 AWG. Contact retention in the housing: 89 N minimum.20 lbf
TE's two solid-contact documents disagree for size 20. Until TE confirms, take the higher figure per wire size as the pass mark (16 AWG 156 N, 18 AWG 111 N, 20 AWG 89 N).ConflictMedium322733
Application spec

Connector: 114-151010 rev D2. Contacts: 114-151004 rev E1 (solid 0460/0462-xxx-20), 114-151003 rev J1 (stamped 1060/1062-20-01). Tools: 0425-071-0000 rev D (HDT-48-00), 0425-072-0000 rev A (DTT-20-00).

Sourced2427262829

Assembly

  1. Check the insulation OD is within the DTM seal range of 1.35-3.05 mm (16-20 AWG).24
  2. Strip the wire to the length for the contact type and check for damaged strands.272829
  3. Solid contacts: set the HDT-48-00 dial to the wire size, insert the wire until strands show in the inspection hole with a 0.63-2.54 mm gap to the insulation, and close the handles until the ratchet releases.2827
  4. Stamped contacts: seat the contact fully in the locator of the cavity marked for the wire size, insert the wire and close the tool until the ratchet releases.2926
  5. Inspect the crimp: all strands captured, no broken strands, mating end undamaged.2726
  6. Hold the contact about 25 mm behind the crimp barrel, grommet towards you, and push straight in until it stops and locks. Tug the wire lightly to confirm. For 20 AWG and smaller wire, insertion tool M15570-20 may help.24
  7. Fit a sealing plug in every unused cavity; it should sit flush with the cavity opening, not pushed through.24
  8. Push the wedge lock in until it snaps into the locked position (pliers can help on receptacles; plugs by hand).24
  9. Mate until there is an audible and tactile click, then check the latch is fully engaged.24

Removal

  1. Unmate: press the plug latch to its stop and pull the halves apart.24
  2. Grip the wedge lock with small long-nose pliers (or the DT-RT1 hook) and pull it straight out. Avoid damaging its inner ribs if it will be reused.2430
  3. Push the DT-RT1 screwdriver tip or a small flat screwdriver into the contact's cavity to release the locking finger.2430
  4. Pull the wire until the contact comes out, holding the rear grommet in place if the housing has no end cap.24
  5. If the grommet came out, inspect it for cuts or cracks and replace it if damaged.24

Summarised in our own words from the maker's application specifications and instruction sheets cited above. Disconnect the battery before working on a vehicle harness. A crimp is only as good as its pull test: check samples with your tool and wire before building a loom. Choosing a crimp tool →

Kit parts for this family

ItemPart numberDescriptionWireQtySource
Cavity plug0413-204-2005Sealing plug, red PBT, size 20 - the plug TE specifies for DTMResolves the library's 'unverified' flag: TE's DTM application spec names this plug.Allper unused cavity24
Crimp toolHDT-48-00Hand crimp tool for solid size 20 contacts16-20 AWG12028
Crimp tool2391435-1Current TE hand crimp tool for stamped size 20 contacts 1060/1062-20-01 and 1062-20-03114-151003 rev J1 names this tool; DTT-20-00 is marked superseded by TE. Instruction sheet 408-35200.16-20 AWG (0.5-1.5 mm2)12631
Removal toolDT-RT1Removal tool for front-release connectors (wedge hook + locking-finger screwdriver)All12430
Removal tool0411-240-2005Size 20 extraction tool already listed in the libraryThe library cites a distributor listing that calls it an HDP extraction tool. TE's DTM application spec names only DT-RT1 for removal (DTM is front-release). Recommend replacing it with DT-RT1 in DTM kits.AllTBCUnverifiedMedium24
OtherM15570-20Insertion tool, size 20 (red); may be needed for wire of 20 AWG or smaller20 AWG124
Other0413-216-2005Keying pin, red PBT (optional, prevents mis-mating)Allas needed24

Where it's used

Our harness designs

Not used in our current harness designs.

Sensors that mate with it

No sensor in our sensor library lists this connector yet.

Factory (OEM) use

No factory ECU in our pinout library uses this connector family.

Frequently asked

How many amps is a Deutsch DTM connector rated for?

TE rates each DTM contact at 7.5 A continuous, and the housings at 250 V AC or DC. That covers sensors, signal lines and small solenoids. For loads above 7.5 A, step up to the Deutsch DT series with size 16 contacts, or the DTP series for heavier power feeds.12

What is the difference between Deutsch DT and DTM?

DTM is the smaller family. It uses size 20 contacts rated 7.5 A, while DT uses size 16 contacts. Both come in 2 to 12-way housings with separate wedge locks and silicone seals. Their contacts, wedges and housings do not interchange, so pick the family by wire size and current.123

What wire size fits Deutsch DTM contacts?

It depends on the contact. Solid contacts come in 20 AWG (0.5 mm²) and 16-18 AWG (0.75-1.5 mm²) versions, while stamped contacts cover 16-22 AWG. The insulation must also fall within 1.35-3.05 mm for the grommet to seal. TE's series FAQ quotes a wider 14-22 AWG range.Medium9111521

What crimp tool do DTM contacts need?

Solid DTM contacts need a four-indent closed-barrel tool such as TE's HDT-48-00, which covers sizes 12, 16 and 20. Stamped contacts need an open-barrel F-crimp tool; TE's size 20 hand tool DTT-20-00 is sold for them but is now superseded, so check TE for its replacement.Medium202116

Are DTM connectors waterproof?

Yes, when assembled correctly. TE rates DTM housings IP68 and IP6K9K and says wired, mated pairs withstand immersion under three feet of water. That relies on silicone grommets around each wire, the interfacial seal and a plug in any unused cavity.12

Keep going

Related

Sources

35 sources
  1. DEUTSCH DTM connectors FAQ · TE Connectivity · vendor-doc · retrieved 2026-10-27
  2. DTM04-4P product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  3. DTM04-6P product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  4. DTM06-4S product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  5. Customer drawing DTM04-4P rev A · TE Connectivity (Deutsch) · vendor-doc · retrieved 2026-10-27
  6. Customer drawing DTM06-4S rev A · TE Connectivity (Deutsch) · vendor-doc · retrieved 2026-10-27
  7. Customer drawing DTM06-6S rev A · TE Connectivity (Deutsch) · vendor-doc · retrieved 2026-10-27
  8. WM-6P wedge lock product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  9. 0460-202-20141 pin contact product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  10. 0462-201-20141 socket contact product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  11. 0460-010-20141 pin contact product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  12. 0462-005-20141 socket contact product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  13. 0460-202-2031 gold pin contact product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  14. 0462-201-2031 gold socket contact product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  15. 1060-20-0122 stamped pin contact product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  16. 1062-20-0122 stamped socket contact product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  17. 1060-20-0144 stamped gold pin contact product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  18. 1062-20-0144 stamped gold socket contact product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  19. 0413-204-2005 sealing plug, size 20 · TE Connectivity · vendor-doc · retrieved 2026-10-27
  20. HDT-48-00 hand crimp tool product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  21. DTT-20-00 crimp tool product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  22. 0411-240-2005 extraction tool, size 20 · element14 / Farnell · vendor-doc · retrieved 2026-10-27
  23. 0460-202-16141 size 16 solid pin (Deutsch DT contact) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  24. Application Specification 114-151010 DEUTSCH DTM Series Connector System, rev D2 (23 Sep 2025) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  25. Product Specification 108-151010 DEUTSCH DTM Series, rev F · TE Connectivity · vendor-doc · retrieved 2026-10-27
  26. Application Specification 114-151003 DEUTSCH Size 20 S&F Pin and Socket Contacts, rev J1 (04 Jun 2026) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  27. Application Specification 114-151004 DEUTSCH Size 4-20 Solid Pin and Socket Contacts, rev E1 (14 Sep 2022) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  28. Instruction Sheet 0425-071-0000 DEUTSCH Field Maintenance Crimp Tool HDT-48-00, rev D (15 Jan 2018) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  29. Instruction Guide 0425-072-0000 for DTT-20-00, rev A · TE Connectivity · vendor-doc · retrieved 2026-10-27
  30. Instruction Sheet 408-151008 DEUTSCH Removal Tool DT-RT1 for Front-Release Connectors, rev B (22 Jan 2015) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  31. 2391435-1 product page (SDE F pin/socket 16-18 hand tool) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  32. Product Specification 108-151000 DEUTSCH Stamped and Formed Contacts, rev J (25 Sep 2024) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  33. Product Specification 108-151004 DEUTSCH Solid Contacts (HD), rev E (20 Aug 2020) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  34. Application Specification 114-151000 DEUTSCH Size 16 S&F Pin and Socket Contacts, rev R (08 Aug 2025) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  35. Instruction Guide 0425-037-0000 for DTT-16-00, rev D · TE Connectivity · vendor-doc · retrieved 2026-10-27

Facts come from manufacturer documents and distributor spec pages, read on the retrieval date shown. Part numbers and ratings change: confirm against the maker's current drawing before you order. Manufacturer names identify parts only; no affiliation is implied.