TE Connectivity (Deutsch)

Deutsch DT connectors

DT seriesDeutsch DT connectorDT04 / DT06DEUTSCH DT

A Deutsch connector from the DT series is a sealed, rectangular wire-to-wire connector made by TE Connectivity that uses size 16 contacts rated at 13 A each. DT housings come in 2, 3, 4, 6, 8 and 12 way layouts, take 14-20 AWG wire, work from -55 to 125 °C and hold their contacts with a separate wedge lock.21415

At a glance

Contact size
  • Size 16
  • Mating pin diameter 1.59 mm0.063 in
Sourced1518
Current13 A maximum per contactSourced1514
Layouts2, 3, 4, 6, 8 and 12 waySourced · medium2
Wire range14-20 AWG, set by the contact0.5-2 mm²Sourced25711
Insulation OD2.23-3.68mm0.088-0.145 inSourced1517
Temperature-55 to 125°C-67 to 257 °FSourced1520
SealingIP68 and IP6K9KSourced1520
Operating voltage250V AC/DCSourced15
Housing
  • Glass-filled polyamide, grey
  • Silicone seals
Sourced152
Wedge lockSeparate PBT wedge: green for receptacles, orange for plugsSourced24252829

Part numbers

What a Deutsch DT connector is

The Deutsch DT connector is TE Connectivity's general-purpose sealed connector for size 16 contacts.

Each housing has an integrated latch, a rear silicone grommet and a separate wedge that locks the contacts in place.142

Part numbers tell you the half. DT04 housings are receptacles that hold pin contacts; DT06 housings are plugs that hold socket contacts. The number after the dash is the cavity count, and the letter is P for pins or S for sockets.151816191720

TE aims the DT series at industrial and commercial vehicles and other harsh-environment wiring. Mouser's launch note adds that J1939/11 versions exist for three-wire CAN.Medium142

Common DT housings and their wedges

All six housings below carry size 16 contacts rated 13 A, work from -55 to 125 °C and seal to IP68 and IP6K9K.

Pitch, 2 way5.46mm0.215 inSourced1518
Pitch, 4 way4.47 mm (DT04-4P) / 4.44 mmDT06-4SThe 0.03 mm gap looks like rounding.Sourced1619
Pitch, 6 way3.81 mm (DT04-6P) / 4.44 mmDT06-6STE's pages for the two mating 6-way housings print different centrelines. Check the TE drawing before relying on either.Conflict1720
DT receptacles and plugs (TE product pages)151816191720242526272829
PartHalfWays / rowsL x W x H (mm)Wedge lock
DT04-2PReceptacle (pins)2 / 143.38 x 17.15 x 17.02W2P (green)
DT06-2SPlug (sockets)2 / 128.4 x 15.01 x 15.77W2S (orange)
DT04-4PReceptacle (pins)4 / 245.92 x 20.83 x 19.71W4P (green)
DT06-4SPlug (sockets)4 / 230.94 x 18.19 x 18.39W4S-ZZ (orange)
DT04-6PReceptacle (pins)6 / 245.92 x 20.83 x 24.16W6P (green)
DT06-6SPlug (sockets)6 / 230.94 x 18.19 x 22.63W6S (orange)

Sizes are TE product-page values for the plain in-line housing.151816191720

DT contacts and tools

DT housings use Deutsch common contacts in size 16.

Crimp tool, solid contacts

HDT-48-00: four-indent hand tool for solid size 12, 16 and 20 contacts

Sourced23
Crimp tool, size 16DTT-16-00: straight-action hand tool, size 16 (superseded)TE's page does not state the contact style or wire range. Check instruction sheet 0425-037-0000.Sourced · medium22
Contact removal tool
  • DT-RT1, front release
  • TE lists DT, DTP and DTM
Sourced13
Sealing plug114017, white, for size 12 and 16 cavitiesSourced · medium1
Size 16 contacts for DT housings (TE product pages; all 13 A typical)58697101112
PinSocketStyleWirePlating
0460-202-161410462-201-16141Solid16-20 AWG (0.5-1.5 mm²)Nickel
0460-202-16310462-201-1631Solid16-20 AWG (0.5-1.5 mm²)Gold
0460-215-161410462-209-16141Solid14 AWG (2 mm²)Nickel
1060-16-01221062-16-0122Stamped and formed14-18 AWG (0.75-2 mm²)Nickel contact, tin crimp

Solid (machined) contacts take an indent crimp; stamped and formed contacts come on reels and take an F-crimp. TE states that each style needs its own Deutsch tooling.581114

How to assemble and service a DT connector

Crimp each contact with Deutsch tooling.

Hold the contact about 25 mm (1 in) behind the barrel and push it straight through the rear grommet until it clicks, then tug lightly to confirm it is locked.14

When every cavity is filled with a contact or sealing plug, push the wedge in from the mating face until it clicks. Both halves use the same procedure.141

To remove a contact, pull the wedge straight out with needle-nose pliers, a screwdriver or a hook. Release the locking finger with a small screwdriver while easing the wire back, and hold the rear seal so it stays in place.14

DT vs DTM vs DTP

DT is the middle of three sister series.

Deutsch DT family series comparedMedium21521
SeriesContact sizeCurrent per contactLayouts
DTM207.5 A2-12 way
DT1613 A2, 3, 4, 6, 8, 12 way
DTP1225 A2 and 4 way

DTM uses smaller size 20 contacts for signal-heavy layouts; DTP uses size 12 contacts for power feeds. The housings share the latch and wedge design but contacts and wedges do not cross over.Medium214

Common mistakes

Swapping wedges between halves.

Receptacle wedges (W2P, W4P, W6P) are green and plug wedges (W2S, W4S-ZZ, W6S) are orange on TE's pages; each fits only its own half and cavity count.242526272829

Buying the wrong cavity plug. 0413-204-2005 is a red size 20 plug that TE lists for the HD30 series; a size 16 DT cavity needs a size 12/16 plug such as 114017.Medium41

Buying an HD-series extraction tool. TE lists 0411-204-1605 for HD, HD30, DRC and HDP connectors, not DT. DT contacts release with a small screwdriver or the DT-RT1 tool once the wedge is out.31314

Using insulation that is too thin. The grommet seals on 2.23-3.68 mm (0.088-0.145 in) insulation; thin-wall wire below that range will not seal.15

CAD and drawings

  • Application specApplication specification 114-151009 rev C3 (DT connector system) · 114-15100930Download from TE Connectivity ↗No login at last check; the maker may change this
  • Product specProduct specification 108-151009 rev E (DT series) · 108-15100931Download from TE Connectivity ↗No login at last check; the maker may change this
  • Application specApplication specification 114-151004 rev E1 (size 4-20 solid contacts) · 114-15100432Download from TE Connectivity ↗No login at last check; the maker may change this
  • Application specApplication specification 114-151000 rev R (size 16 stamped and formed contacts 1060/1062-16-01 etc.) · 114-15100033Download from TE Connectivity ↗No login at last check; the maker may change this
  • Instruction sheetInstruction sheet 0425-071-0000 rev D (HDT-48-00 crimp tool) · 0425-071-000034Download from TE Connectivity ↗No login at last check; the maker may change this
  • Instruction sheetInstruction guide 0425-037-0000 rev D (DTT-16-00 stamped-contact crimp tool, superseded) · 0425-037-000035Download from TE Connectivity ↗No login at last check; the maker may change this
  • Instruction sheetInstruction sheet 408-151008 rev B (DT-RT1 removal tool) · 408-15100836Download from TE Connectivity ↗No login at last check; the maker may change this

We link to the maker's own downloads and do not rehost drawings, 3D models or specifications: the makers' terms grant no redistribution. Our cavity maps are drawn from the cavity numbers, never traced from these drawings.

Crimp and assembly quick card

Strip length
  • Solid size 16 (0460-202-16141, 0462-201-16141, 0460-215-16141, 0462-209-16141): 6.35-7.92 mm (0.250-0.312 in). Stamped size 16 (1060/1062-16-01xx): 3.81-5.08 mm0.150-0.200 in
  • The DTT-16-00 guide gives 4.45 +/- 0.64 mm (0.175 +/- 0.025 in), which sits inside that window.
Sourced32343335
Crimp height
  • Stamped 1060/1062-16-01xx (wire barrel): 14 AWG 1.35-1.43 mm
  • 16 AWG 1.22-1.30 mm
  • 18 AWG 1.19-1.27 mm
  • Crimp width 2.31-2.47 mm (insulation OD 1.91-3.56 mm). Solid contacts on HDT-48-00 (reference only, TE says validate by pull test): 0460-202-16/0462-201-16 at 18 AWG 0.85-0.94 mm at the lock indent, 1.07-1.15 mm at the entry indent
  • 0460-215-16/0462-209-16 at 14 AWG 1.06-1.31 / 1.28-1.52 mm (dial 1.5).
An older DTT-16-01 envelope drawing gives 1.22-1.32 mm height and 2.39-2.54 mm width at 18 AWG for 1060/1062-16-01; the current 114-151000 rev R values are used. The HDT-48-00 table in 114-151004 lists 0460-202-16/0462-201-16 only at 18 AWG; heights for 16 and 20 AWG on that tool are not published there.Sourced3332
Pull-out force (minimum)
  • Crimp tensile minimum, solid size 16: 14 AWG 311 N70 lbf
  • 16 AWG 156 N35 lbf
  • 18 AWG 111 N25 lbf
  • 20 AWG 67 N (15 lbf). Stamped size 16: 14-18 AWG 111 N25 lbf
  • 20 AWG 67 N. Contact retention in the housing: 111 N minimum. Pull rate 25 mm/min.15 lbf · 25 lbf
A 2009 Deutsch manual listed 89 N for solid size 16 at 20 AWG; current TE specs give 67 N.Sourced323738
Application spec

Connector: 114-151009 rev C3. Contacts: 114-151004 rev E1 (solid 0460/0462), 114-151000 rev R (stamped 1060/1062-16-01). Tools: 0425-071-0000 rev D (HDT-48-00), 0425-037-0000 rev D (DTT-16-00).

Sourced3032333435

Assembly

  1. Choose the contact by wire size and check the insulation OD fits the housing seal: standard DT (N-seal) seals 2.23-3.68 mm OD; the E-seal option seals 1.35-3.05 mm (14-20 AWG).30
  2. Strip the wire to the length for the contact type, then check for missing or damaged strands.323433
  3. Solid contacts: set the HDT-48-00 dial to the wire size, push the stripped wire into the barrel until strands show in the inspection hole, leave a 0.63-2.54 mm gap between barrel and insulation, centre the contact and close the handles until the ratchet releases.3432
  4. Stamped contacts: put the contact in the tool cavity marked for the wire size, insert the stripped wire and close the tool until the ratchet releases.3533
  5. Inspect the crimp: all strands inside the barrel, none broken, mating end straight.3233
  6. On plugs, make sure the front (interface) seal is present and seated before inserting contacts.30
  7. Hold the contact about 25 mm behind the crimp barrel, grommet towards you, and push it straight in until it stops and locks. Tug the wire lightly to confirm.30
  8. Fit a sealing plug in every unused cavity.30
  9. Push the wedge lock in until it snaps into the locked position. On receptacles a DT-RT1 or small long-nose pliers can help; on plugs it goes in by hand.30
  10. Mate plug to receptacle until the latch clicks, then check the latch is fully engaged.Medium30

Removal

  1. Unmate the connector.Medium30
  2. Plug (sockets): slide the DT-RT1 screwdriver tip under the wedge lock and lift it out evenly, taking care not to damage the front seal.3036
  3. Receptacle (pins): on 2, 4, 6 and 12-way, hook the DT-RT1 hook tip in the wedge removal slot and pull straight out; on 3 and 8-way and keyed 2/4-way wedges, grip the wedge post with small long-nose pliers.3036
  4. Push the DT-RT1 screwdriver tip (or a small flat screwdriver) into the contact's cavity to lift the locking finger off the contact.3036
  5. Holding the rear grommet in place, pull the wire back until the contact comes out.3036
  6. Inspect the grommet and wedge lock; replace any damaged part before reassembly.30

Summarised in our own words from the maker's application specifications and instruction sheets cited above. Disconnect the battery before working on a vehicle harness. A crimp is only as good as its pull test: check samples with your tool and wire before building a loom. Choosing a crimp tool →

Kit parts for this family

ItemPart numberDescriptionWireQtySource
Cavity plug114017Sealing plug, white PBT, fits N-seal and E-seal DT housingsConfirms the plug already in the library.Allper unused cavity30
Cavity plug0413-217-1605Locking sealing plug, white PBT, N-seal and E-sealAlternative to 114017.Allper unused cavity30
Cavity plug776363-1Sealing plug, yellow PBT, N-seal (standard) housingsAlternative for standard-seal housings.Allper unused cavity30
Crimp toolHDT-48-00Hand crimp tool for solid size 12/16/20 contacts14-20 AWG (size 16)12334
Crimp tool2388970-1Current TE hand crimp tool for stamped size 16 contacts 1060/1062-14-01, -14-10, -16-01, -16-07, -16-09114-151000 rev R names this in place of DTT-16-00, which TE marks superseded. Instruction sheet 408-35190.14-16 AWG (1.0-2.0 mm2)133
Crimp tool2390264-1Current TE hand crimp tool for stamped size 16 contacts -16-01, -16-07, -16-09 at 18 AWGInstruction sheet 408-35284.18 AWG (0.75 mm2)133
Removal toolDT-RT1Removal tool: hook end lifts the wedge lock, screwdriver end releases the locking fingerAll13036
Removal tool0411-204-1605Size 16 extraction tool already listed in the libraryTE's DT application spec names only DT-RT1 (front release) for contact removal; no TE source found tying 0411-204-1605 to DT. Recommend dropping it from the DT kit or marking it as not required.AllTBCUnverifiedMedium3036
OtherM15570-16Insertion tool, size 16 (blue); may be needed for contacts on wire of 20 AWG or smaller20 AWG130
Other0413-215-1605Keying pin (optional) for plug cavities to prevent mis-mating of like connectorsAllas needed30

Where it's used

Our harness designs

Not used in our current harness designs.

Sensors that mate with it

No sensor in our sensor library lists this connector yet.

Factory (OEM) use

No factory ECU in our pinout library uses this connector family.

Frequently asked

What is a Deutsch DT connector?

A Deutsch DT connector is a sealed, rectangular wire-to-wire connector from TE Connectivity that uses size 16 contacts rated at 13 A each. It comes in 2 to 12 way layouts, seals to IP68 and IP6K9K, and works from -55 to 125 °C. A separate wedge lock holds the crimped contacts in the housing.21514

What is the difference between DT04 and DT06?

DT04 housings are receptacles that hold pin contacts, and DT06 housings are plugs that hold socket contacts. A DT04 always mates with the DT06 of the same cavity count, for example DT04-4P with DT06-4S. Each half takes its own wedge lock: green for receptacles, orange for plugs on TE's standard parts.Medium1518161917202627

What wire size do Deutsch DT connectors take?

Deutsch DT connectors take 14-20 AWG (0.5-2 mm²) wire, and the contact sets the exact range. Solid size 16 contacts such as 0460-202-16141 cover 16-20 AWG, solid 14 AWG versions exist, and stamped 1060-16-0122 contacts cover 14-18 AWG. Insulation must be 2.23-3.68 mm across to seal in the grommet.571115

How do you remove pins from a Deutsch DT connector?

Pull the wedge lock straight out with needle-nose pliers or a hook. Then push the contact's locking finger aside with a small screwdriver, or use the DT-RT1 removal tool, while gently pulling the wire back. Hold the rear seal in place as the contact comes out, because it can be pulled out of position.1413

Do Deutsch DT connectors need a wedge lock?

Yes. The wedge lock is the secondary lock that holds each contact against being pulled back out, and TE sells it separately from the housing. Fit it after every contact has clicked into place; if it will not seat, one contact is probably not fully inserted.Medium242514

Keep going

Related

Sources

40 sources
  1. 114017 sealing plug, size 12 and 16 · BuyDeutsch (distributor) · vendor-doc · retrieved 2026-10-27
  2. Mouser offers wide inventory of DEUTSCH DT family of cable-to-cable connectors from TE Connectivity · Elektor Magazine · press · retrieved 2026-10-27
  3. 0411-204-1605 size 16 extraction tool product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  4. 0413-204-2005 sealing plug product page (size 20) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  5. 0460-202-16141 size 16 solid pin, nickel · TE Connectivity · vendor-doc · retrieved 2026-10-27
  6. 0460-202-1631 size 16 solid pin, gold · TE Connectivity · vendor-doc · retrieved 2026-10-27
  7. 0460-215-16141 size 16 solid pin for 14 AWG · TE Connectivity · vendor-doc · retrieved 2026-10-27
  8. 0462-201-16141 size 16 solid socket, nickel · TE Connectivity · vendor-doc · retrieved 2026-10-27
  9. 0462-201-1631 size 16 solid socket, gold · TE Connectivity · vendor-doc · retrieved 2026-10-27
  10. 0462-209-16141 size 16 solid socket for 14 AWG · TE Connectivity · vendor-doc · retrieved 2026-10-27
  11. 1060-16-0122 size 16 stamped and formed pin · TE Connectivity · vendor-doc · retrieved 2026-10-27
  12. 1062-16-0122 size 16 stamped and formed socket · TE Connectivity · vendor-doc · retrieved 2026-10-27
  13. DT-RT1 contact removal tool product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  14. DEUTSCH DT Series Connectors (overview and assembly video page) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  15. DT04-2P product page (DEUTSCH DT receptacle, 2 way) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  16. DT04-4P product page (DEUTSCH DT receptacle, 4 way) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  17. DT04-6P product page (DEUTSCH DT receptacle, 6 way) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  18. DT06-2S product page (DEUTSCH DT plug, 2 way) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  19. DT06-4S product page (DEUTSCH DT plug, 4 way) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  20. DT06-6S product page (DEUTSCH DT plug, 6 way) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  21. DTP04-2P product page (DEUTSCH DTP receptacle, 2 way) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  22. DTT-16-00 hand crimp tool product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  23. HDT-48-00 hand crimp tool product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  24. W2P wedge lock product page (2 way receptacle, DT) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  25. W2S wedge lock product page (2 contact plug, DT) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  26. W4P wedge lock product page (4 way receptacle, DT) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  27. W4S-ZZ wedge lock product page (4 way plug, DT) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  28. W6P wedge lock product page (6 way receptacle, DT) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  29. W6S wedge lock product page (6 way plug, DT) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  30. Application Specification 114-151009 DEUTSCH DT Series Connector System, rev C3 (14 Oct 2024) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  31. Product Specification 108-151009 DEUTSCH DT Series, rev E · TE Connectivity · vendor-doc · retrieved 2026-10-27
  32. Application Specification 114-151004 DEUTSCH Size 4-20 Solid Pin and Socket Contacts, rev E1 (14 Sep 2022) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  33. Application Specification 114-151000 DEUTSCH Size 16 S&F Pin and Socket Contacts, rev R (08 Aug 2025) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  34. Instruction Sheet 0425-071-0000 DEUTSCH Field Maintenance Crimp Tool HDT-48-00, rev D (15 Jan 2018) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  35. Instruction Guide 0425-037-0000 for DTT-16-00, rev D · TE Connectivity · vendor-doc · retrieved 2026-10-27
  36. Instruction Sheet 408-151008 DEUTSCH Removal Tool DT-RT1 for Front-Release Connectors, rev B (22 Jan 2015) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  37. Product Specification 108-151004 DEUTSCH Solid Contacts (HD), rev E (20 Aug 2020) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  38. Product Specification 108-151000 DEUTSCH Stamped and Formed Contacts, rev J (25 Sep 2024) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  39. Instruction Guide 0425-072-0000 for DTT-20-00, rev A · TE Connectivity · vendor-doc · retrieved 2026-10-27
  40. Application Specification 114-151003 DEUTSCH Size 20 S&F Pin and Socket Contacts, rev J1 (04 Jun 2026) · TE Connectivity · vendor-doc · retrieved 2026-10-27

Facts come from manufacturer documents and distributor spec pages, read on the retrieval date shown. Part numbers and ratings change: confirm against the maker's current drawing before you order. Manufacturer names identify parts only; no affiliation is implied.