Aptiv (formerly Delphi)

Aptiv Weather Pack connectors

Weather-PackWeatherpackDelphi Weather Pack

A Weatherpack connector is Aptiv's sealed round pin-and-sleeve connector system, sold through Delphi for decades. Housings come in 2, 3, 4 and 6-way versions, terminals cover 20-12 AWG wire in three sizes, and distributors list a -40 to 125 °C rating. Each wire carries its own silicone cable seal, and the housings seal to each other.Medium12

At a glance

Ways2,3, 4 and 6Sourced · medium1
Wire range20-12 AWG in three terminal sizes: 20-18, 16-14 and 12Sourced · medium1
Terminal styleRound pin and sleeve, tin plated, dual locking tangsSourced · medium12
Temperature-40 to 125°C-40 to 257 °FSourced · medium1
SealingMulti-rib silicone seals on each wire and between housingsSourced · medium1
Current ratingNot confirmedNo Aptiv or distributor page found states a current rating per terminal. Distributor listings quote figures for whole housings without naming the terminal and wire size.Researched, unverified
Crimp tool12014254sealed Weather Pack pin and sleeve, 0.5-2.0 mm²Sourced2
Removal tool1201401224-12 AWGSourced · medium1

What a Weatherpack connector is

Weatherpack is a sealed connector family from Aptiv, formerly Delphi.

It uses round pin and sleeve terminals, which distributors say helps against stress relaxation, and two locking tangs per terminal.Medium12

Every wire passes through its own silicone cable seal, crimped together with the terminal. The housings carry a multi-rib seal so the mated pair keeps out water, dirt and dust.Medium12

Weatherpack housings

Housings come in male and female halves that latch together.

Sealed Weatherpack housing pairs listed by a distributor.Medium1
WaysMale housingFemale housing
21201097312015792
31201071712015793
4 (in-line)1201097412015797
4 (square)1201502412015798
61201097512015799

Order both halves of a pair by part number.Medium1

Weatherpack terminals and tools

Terminals come in three wire ranges, each as a male pin and a female sleeve.

Crimp tool

12014254, sealed Weather Pack pin and sleeve, core and insulation, 0.5-2.0 mm²

Sourced2
Cavity plug12010300greenSourced · medium1
Removal tool1201401224-12 AWGSourced · medium1
Cable sealsNot confirmedThe distributor page lists seal part numbers under a Metri-Pack 280 heading, so they are not quoted here. Match the seal colour to the wire size from an Aptiv source.Researched, unverified
Tin-plated Weatherpack terminals (distributor listing) and tools.Medium1
WireMale pinFemale sleeve
20-18 AWG1208904012089188
16-14 AWG1212458212124580
12 AWG1212458712124581

Distributor part numbers may carry a -L or reel suffix.

Crimp the terminal and its cable seal in one cycle with the sealed Weather Pack tool.Medium12

How to assemble a Weatherpack connector

Slide the cable seal onto the wire first, strip, then crimp terminal and seal together in the 12014254 tool so the seal sits under the insulation wings.Medium21

Push the terminal into the rear of the housing until the tangs click, then close the housing's lock. Fill unused cavities with a cavity plug.Medium1

Common mistakes

Forgetting the cable seal before crimping.

It cannot be added afterwards, and an unsealed wire lets water into the housing.Medium12

Crimping with plain pliers. The insulation wings must close over the seal, which needs the dedicated sealed-terminal die.Medium2

Pulling a terminal without releasing the tangs. Use the removal tool to press both tangs in first.Medium1

CAD and drawings

  • Application specCrimp information sheets per terminal (Delphi, distributor-hosted) · 12089188-CSMedium45678Download from Delphi ↗No login at last check; the maker may change this

We link to the maker's own downloads and do not rehost drawings, 3D models or specifications: the makers' terms grant no redistribution. Our cavity maps are drawn from the cavity numbers, never traced from these drawings.

Crimp and assembly quick card

Strip lengthTBCNot on the crimp information sheetsTBCResearched, unverified
Crimp height
  • Conductor crimp height on SAE thin-wall cable (type 1005): 12089188 / 12089040 at 0.5 mm² 1.10 ±0.05, 0.8 mm² 1.15 ±0.05 mm
  • 12124580 / 12124582 at 1.0 mm² 1.40 ±0.05, 2.0 mm² 1.45 ±0.05 mm. Insulation/seal crimp height about 4.3-4.7 mm. Values change with cable type
  • Read the row for your cable.
Sourced4567
Pull-out force (minimum)
  • Tear-out min on SAE cable: 0.5 mm² 80 N
  • 0.8 mm² 90 N
  • 1.0 mm² 120 N
  • 2.0 mm² 200 N
Sourced4567
Application spec

Delphi crimp information sheets 12089188-CS, 12089040-CS, 12124580-CS, 12124582-CS

Sourced4567

Assembly

  1. Pick the cable seal by insulation OD (see kit extras) and slide it on before stripping.Medium9
  2. Crimp core and seal together in a Weather Pack tool such as 12014254 and check the conductor crimp height against the crimp sheet; Delphi stresses crimp dimensions are critical in the tight cavities.45679
  3. Delphi recommends the Weather-Pack 6060 gauge as a process check on crimped terminals.Medium9
  4. Fit green cavity plug 12010300 in every unused male or female cavity.9

Summarised in our own words from the maker's application specifications and instruction sheets cited above. Disconnect the battery before working on a vehicle harness. A crimp is only as good as its pull test: check samples with your tool and wire before building a loom. Choosing a crimp tool →

Kit parts for this family

ItemPart numberDescriptionWireQtySource
Terminal12020801 / 12089307Female / male terminals for 0.35 (0.22-0.35) mm²0.22-0.35 mm²1 per wire9
Seal15324985 (reel 12089444)Cable seal, purple, 1.60-2.15 mm insulation1.60-2.15 mm OD1 per wire9
Seal15324984 (reel 12041352)Cable seal, tan, 2.03-2.42 mm2.03-2.42 mm OD1 per wire9
Seal15324982 (reel 12015284)Cable seal, green, 2.03-2.85 mm2.03-2.85 mm OD1 per wire9
Seal15324980 (reel 12015359)Cable seal, grey, 2.81-3.49 mm2.81-3.49 mm OD1 per wire9
Seal15324981 (reel 12015360)Cable seal, blue, 3.45-4.30 mm3.45-4.30 mm OD1 per wire9
Seal15324983 (reel 12034365)Cable seal, dark red, 1.29-1.70 mm1.29-1.70 mm OD1 per wire9
Cavity plug12010300Cavity plug, green silicone, 6.7 mm cavityAllper unused cavity9
Removal toolTBCAptiv removal tool for Weather PackExisting data lists 12014012; not re-confirmed in this pass.All1Unverified

Where it's used

Our harness designs

Not used in our current harness designs.

Sensors that mate with it

No sensor in our sensor library lists this connector yet.

Factory (OEM) use

No factory ECU in our pinout library uses this connector family.

Frequently asked

What wire size fits Weatherpack terminals?

Weatherpack terminals come in three sizes: 20-18 AWG, 16-14 AWG and 12 AWG. Distributor listings give male 12089040 and female 12089188 for 20-18 AWG, 12124582 and 12124580 for 16-14 AWG, and 12124587 and 12124581 for 12 AWG. Pick the cable seal for the same wire size.Medium1

What crimp tool do Weatherpack terminals need?

Use a sealed-terminal tool such as 12014254, which the Delphi catalog lists for sealed Weather Pack pin and sleeve terminals on 0.5-2.0 mm² wire. It crimps the core and closes the insulation wings over the cable seal. Plain open-barrel pliers do not form the seal grip correctly.2

How do you remove a Weatherpack terminal?

Use a Weatherpack removal tool, such as 12014012 for 24-12 AWG, to press in the terminal's locking tangs, then pull the wire out from the rear of the housing. Pulling the wire without releasing the tangs can bend them, and a bent tang will not hold the terminal when it is refitted.Medium1

Is Weatherpack the same as Metri-Pack?

No. Both come from Aptiv, but Weatherpack uses round pin and sleeve terminals while Metri-Pack uses flat blades sized by series, such as 150 or 280. Their terminals, seals and housings do not interchange. Metri-Pack offers more ways (up to 16) and series rated up to 60 A.Medium13

Keep going

Related

Sources

9 sources
  1. Aptiv (Delphi) Weather Pack product line · WireCare (distributor) · vendor-doc · retrieved 2026-10-27
  2. Delphi connection systems catalog, Tooling: crimp tools (p. 10.6, distributor-hosted) · Delphi (now Aptiv), hosted by Chip and Dip · vendor-doc · retrieved 2026-10-27
  3. Connectors for Marine Applications (2025) · Aptiv · vendor-doc · retrieved 2026-10-27
  4. Crimp Information Sheet 12089188 (Weather Pack female 0.5-0.8 mm2), distributor-hosted · Delphi (Aptiv), hosted by Corsa-Technic · vendor-doc · retrieved 2026-10-28
  5. Crimp Information Sheet 12124580 (Weather Pack female 1.0-2.0 mm2), distributor-hosted · Delphi (Aptiv), hosted by Corsa-Technic · vendor-doc · retrieved 2026-10-28
  6. Crimp Information Sheet 12089040 (Weather Pack male 0.5-0.8 mm2), distributor-hosted · Delphi (Aptiv), hosted by Corsa-Technic · vendor-doc · retrieved 2026-10-28
  7. Crimp Information Sheet 12124582 (Weather Pack male 1.0-2.0 mm2), distributor-hosted · Delphi (Aptiv), hosted by Corsa-Technic · vendor-doc · retrieved 2026-10-28
  8. Delphi Packard Weather-Pack category page · Corsa-Technic · vendor-doc · retrieved 2026-10-28
  9. Weather-Pack catalog pages 6.16-6.17 (Delphi), distributor-hosted · Delphi (Aptiv), hosted by Corsa-Technic · vendor-doc · retrieved 2026-10-28

Facts come from manufacturer documents and distributor spec pages, read on the retrieval date shown. Part numbers and ratings change: confirm against the maker's current drawing before you order. Manufacturer names identify parts only; no affiliation is implied.