Wiring guide
Automotive wire gauge chart: AWG to mm² and metric cable sizes
An automotive wire gauge chart converts AWG sizes to metric cross-sections. By the AWG definition in ASTM B258, 22 AWG is 0.326 mm², 20 AWG 0.518 mm², 18 AWG 0.823 mm², 16 AWG 1.31 mm², 14 AWG 2.08 mm² and 12 AWG 3.31 mm². Metric ISO 6722 cable comes in fixed steps (0.35, 0.5, 0.75, 1.0, 1.5, 2.5, 4 and 6 mm² among them), so the closest metric size is often slightly smaller.13
Key takeaways
- Higher AWG numbers are thinner wire. Each 3-gauge step roughly halves the area (16 AWG 1.31 mm² vs 19 AWG 0.65 mm²).
- 0.5 mm² is 3% smaller than 20 AWG (0.518 mm²); 0.75 mm² is 9% smaller than 18 AWG.
- Stranded SAE wire carries less copper than the solid AWG figure: 16 AWG 19 x 29 strands is 1.22 mm², not 1.31.
- Size the wire for current, length and voltage drop with the calculator, then check the contact accepts that gauge and insulation OD.
AWG to mm² chart
This automotive wire gauge chart uses the AWG definition that ASTM B258 tabulates: diameter = 0.127 mm x 92^((36 - n) / 39).
| AWG | Diameter (solid) | Area (mm²) | Nearest ISO 6722 size (mm²) |
|---|---|---|---|
| 26 | 0.405 mm (0.0159 in) | 0.129 | 0.13 (not a common ISO size) |
| 24 | 0.511 mm (0.0201 in) | 0.205 | 0.22 (not a common ISO size) |
| 22 | 0.644 mm (0.0253 in) | 0.326 | 0.35 |
| 20 | 0.812 mm (0.0320 in) | 0.518 | 0.5 |
| 18 | 1.024 mm (0.0403 in) | 0.823 | 0.75 below, 1.0 above |
| 16 | 1.291 mm (0.0508 in) | 1.309 | 1.25 or 1.5 |
| 14 | 1.628 mm (0.0641 in) | 2.081 | 2.0 |
| 12 | 2.053 mm (0.0808 in) | 3.309 | 3.0 |
| 10 | 2.588 mm (0.1019 in) | 5.261 | 5.0 |
| 8 | 3.264 mm (0.1285 in) | 8.366 | 8.0 |
| 6 | 4.115 mm (0.1620 in) | 13.3 | 12 below, 16 above |
| 4 | 5.189 mm (0.2043 in) | 21.2 | 20 below, 25 above |
Computed from the ASTM B258 AWG formula and rounded; the ISO sizes are those Prysmian lists for FLRY-B. 'Nearest' ignores current rating.
Areas are for a solid round wire of that gauge.1
Stranded cable of the same AWG number can carry a little more or less copper. Pepperl+Fuchs makes the same point in its own conversion table, listing 20 AWG at 0.52 to 0.60 mm² depending on stranding.2
Metric (ISO 6722) cable sizes
Metric cable is sold by nominal cross-section, and the maker sets the strand count to hit a maximum resistance.
| Size (mm²) | Strands | Max resistance, bare (mΩ/m at 20 °C) | Max OD (mm) | Closest AWG |
|---|---|---|---|---|
| 0.35 | 12 | 54.4 | 1.4 | 22 |
| 0.5 | 16 | 37.1 | 1.6 | 20 |
| 0.75 | 24 | 24.7 | 1.9 | 18 (smaller) |
| 1.0 | 32 | 18.5 | 2.1 | 18 (larger) |
| 1.5 | 30 | 12.7 | 2.4 | 16 (larger) |
| 2.5 | 50 | 7.60 | 3.0 | 14 (larger) |
| 4 | 56 | 4.71 | 3.7 | 12 (larger) |
| 6 | 84 | 3.14 | 4.3 | 10 (larger) |
Closest AWG compares the nominal mm² with the ASTM B258 solid area.
Prysmian's FLRY-B sheet gives that limit per size, which is the number to use for a voltage drop estimate.3
SAE J1128 sizes are not the solid AWG area
SAE J1128 wire is sold by AWG number but built from a set strand count.
| AWG | Stranding (Sycor) | Area from strands (mm²) | Solid AWG area (mm²) |
|---|---|---|---|
| 22 | 7 x 30 AWG (TXL) | 0.356 | 0.326 |
| 20 | 7 x 28 AWG (TXL, GXL, SXL) | 0.567 | 0.518 |
| 18 | 16 x 30 AWG (GXL, SXL) | 0.815 | 0.823 |
| 16 | 19 x 29 AWG (TXL, GXL, SXL) | 1.220 | 1.309 |
| 14 | 19 x 27 AWG (TXL, GXL, SXL) | 1.940 | 2.081 |
| 12 | 19 x 25 AWG (TXL, GXL, SXL) | 3.085 | 3.309 |
| 10 | 19 x 23 AWG (TXL, GXL, SXL) | 4.905 | 5.261 |
Our calculation: strand count x ASTM B258 area of the strand gauge. Sycor lists 18 AWG TXL as 19 x 30 (0.969 mm²); Prestolite lists 16 x 30 or 19 x 31 for 18 AWG TXL.
Multiply it out and the copper area lands below the solid AWG figure at most sizes: 16 AWG built from 19 strands of 29 AWG is about 1.22 mm², roughly 7% under 1.31 mm².Medium641
That gap is small but it adds up on long runs. Use the resistance figure on the wire datasheet, not the chart, when you size a high-current circuit.Medium43
Which Deutsch contact fits each gauge
Gauge also decides which crimp contact you can use.
| Contact | Example part | Wire range | Typical current |
|---|---|---|---|
| Size 20, solid | 0460-202-20141 pin | 20 AWG (0.5 mm²) | 7.5 A |
| Size 20, stamped | 1060-20-0122 pin | 22-16 AWG (0.35-1.5 mm²) | 7.5 A |
| Size 16, solid | 0460-202-16141 pin | 16-20 AWG (0.5-1.5 mm²) | 13 A |
| Size 16, solid, 14 AWG | 0460-215-16141 pin | 14 AWG (2 mm²) | 13 A |
| Size 16, stamped | 1060-16-0122 pin | 18-14 AWG (0.75-2 mm²) | 13 A |
| Size 12, solid | 0460-204-12141 pin | 14-12 AWG (2.08-3.31 mm²) | 25 A |
TE publishes the wire range on every Deutsch contact page, and the size 16 solid range stops at 16 AWG, so 14 AWG needs its own contact.710
Typical sizes by circuit
Wire size follows current, run length and the voltage drop you accept.
| Circuit | Common size | Why |
|---|---|---|
| Sensor signals, 5 V reference, sensor ground | 22-20 AWG (0.35-0.5 mm²) | Milliamp currents; size 20 contacts |
| CAN bus pair | 22-20 AWG twisted pair | Signal only |
| Injector and coil feeds | 18-16 AWG (0.75-1.5 mm²) | A few amps per circuit |
| Fuel pump, fans, ECU main power | 14-10 AWG and up | Size with the calculator |
Editorial starting points used in many harnesses, not a rating from any standard. Size every power circuit with the wire-gauge calculator and the fuse.
The resistance per metre in the metric table drives that drop, so a long run needs a larger size than the same current over a short one.3
Common chart mistakes
Treating 0.5 mm² and 20 AWG as identical is usually harmless at signal currents, since the difference is 3%.
Swapping 0.75 mm² for 18 AWG loses 9% of the copper, which matters on a long power feed.13
Gauge does not set insulation size. At 18 AWG, Sycor's TXL measures 0.079 in (2.01 mm) and its SXL 0.107 in (2.72 mm), so check the seal range of the connector as well.65
Frequently asked
What is 18 AWG in mm²?
18 AWG is 0.823 mm² as a solid wire by the ASTM B258 AWG formula. Metric cable has no exact match: 0.75 mm² is about 9% smaller and 1.0 mm² about 22% larger. Stranded SAE 18 AWG built from 16 strands of 30 AWG works out to about 0.815 mm².143
Is 0.5 mm² the same as 20 AWG?
Close, but not the same. 20 AWG is 0.518 mm² as a solid wire, so 0.5 mm² is about 3% smaller. For sensor and signal wiring the difference does not matter. Prysmian's 0.5 mm² FLRY-B has a maximum resistance of 37.1 mΩ/m, which you can use directly in a voltage drop estimate.13
Does a higher AWG number mean thicker wire?
No, a higher AWG number means thinner wire. The ASTM B258 formula shrinks the diameter by a fixed ratio for each step, so 20 AWG is 0.812 mm across and 10 AWG is 2.588 mm. Every three gauges roughly halves or doubles the copper area.1
What metric wire replaces 14 AWG?
2.0 mm² is the closest metric size to 14 AWG, which is 2.08 mm² solid. If your supplier only stocks 1.5 and 2.5 mm², choose 2.5 mm², because 1.5 mm² has about 28% less copper. Prysmian lists 2.5 mm² FLRY-B at 7.60 mΩ/m maximum and 3.0 mm² maximum outside diameter.13
What size Deutsch pin do I need for 14 AWG wire?
Use a size 16 contact made for 14 AWG, such as TE's solid 0460-215-16141 pin, or the stamped 1060-16-0122 pin, which takes 18-14 AWG. The standard solid size 16 pin (0460-202-16141) stops at 16 AWG. For 12 AWG, move to a size 12 DTP contact rated 25 A typical.101179
Keep going
Related
Sources
12 sources
- ASTM B258-18 Standard nominal diameters and cross-sectional areas of AWG sizes of solid round wires (scope) · ASTM International · standard · retrieved 2026-10-27
- AWG to mm² conversion table (catalog page) · Pepperl+Fuchs · vendor-doc · retrieved 2026-10-27
- FLRY-B automotive cable datasheet DF 049-2000 index V (issued 2020-10-06) · Prysmian Kabel und Systeme GmbH · vendor-doc · retrieved 2026-10-27
- Type GXL wire, primary thin wall (SAE J1128) product page · Sycor Technology · vendor-doc · retrieved 2026-10-27
- Type SXL wire, primary standard wall (SAE J1128) product page · Sycor Technology · vendor-doc · retrieved 2026-10-27
- Type TXL wire, primary extra thin wall (SAE J1128) product page · Sycor Technology · vendor-doc · retrieved 2026-10-27
- 0460-202-16141 pin, solid, size 16, nickel: product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
- 0460-202-20141 pin, solid, size 20, nickel: product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
- 0460-204-12141 pin, solid, size 12: product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
- 0460-215-16141 pin, solid, size 16, 14 AWG: product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
- 1060-16-0122 pin, stamped and formed, size 16: product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
- 1060-20-0122 pin, stamped and formed, size 20: product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
Facts come from manufacturer documents and distributor spec pages, read on the retrieval date shown. Part numbers and ratings change: confirm against the maker's current drawing before you order. Manufacturer names identify parts only; no affiliation is implied.

